Rodrigo Martins

In this paper a set of one-dimensional simulations of a-Si:H p-i-n junctions under different illumination conditions and with different intrinsic layer are presented. The simulation program ASCA permits the analysis of the internal electrical behaviour of the cell allowing a comparison among the different internal configurations determined by a change in the input set. Results about the internal electric configuration will be presented and discussed outlining their influence on the current tension characteristic curve. Considerations about the drift-diffusion and the generation-recombination balance distributions, outlined by the simulation, can be used to explain the correlation between the basic device output, the i-layer characteristics (thickness and DOS), the incident radiation intensity and photon energy. © 2002 Elsevier Science B.V. All rights reserved.

In this work we show that it is possible to control the plasma species present near the substrate surface, from what is usually associated with an α regime (a plasma free of particles) to a γ' regime (a plasma where particles are present) and simultaneously control the energy of the ions striking the substrate during a-Si:H deposition from a silane glow discharge in a modified triode (MT) type PECVD reactor, where a DC mesh electrode biased with Vpol is located in front of the r.f electrode. The presence of large particles in the plasma leads to the deposition of the films with the poorest optoelectronic properties. When the particle size in the plasma decrease the film properties improve, but, when particles are no longer present in the plasma region close to the substrate, like in a α like regime, the properties of the films deteriorate again. The results show that the best transport properties are achieved for the films deposited in the α-γ' transition regime corresponding to 0V<Vpol<51V. Under this condition the films present a dark conductivity, σ d ≈ 10-11 (Ωcm)-1, photosensitivity, S ≈ 107, activation energy, ΔE ≈ 0.9 eV, hydrogen content, CH ≈ 10%, factor of microstructure, R ≈ 0.085 and an optical gap, Eop ≈ 1.77 eV.

Tensile tests were performed on PET films coated with Al doped zinc oxide films by RF magnetron sputtering. During the tensile elongation, the electrical resistance of the oxide was evaluated in situ. The results indicate that the increase in the electrical resistance is related to the crack debsity and crack width, which also depends on the film thickness.

Ferroelectric and high dielectric permittivity films are currently being investigated in view of their use as gate dielectrics in MIS structures. Along with the suppression of tunnelling currents at small gate thickness, they provide a memory function to MIS structures, which can be used in non-volatile memory applications. In this work we report fabrication and characterization of novel metal-ferroelectric-amorphous silicon structures. The structures consist of glass/ITO substrates coated with PZT 20/80 films (sol-gel) followed by an active layer (i-a-SiC:H, deposited by plasma enhanced chemical vapor deposition (PECVD)). A strong capacitance hysteresis is observed in C-V curves in electron accumulation region (VG > 0), accompanied with a large increase in the capacitance of ferroelectric-semiconductor structures at low frequencies. Threshold voltage for electron accumulation is about 10 V being dependent on the ferroelectric polarization switching. © 2002 Elsevier Science B.V. All rights reserved.

In this paper we report results of nanocrystalline p-doped silicon films produced by hot wire chemical vapour deposition technique with Ta filaments, using a pre-mixed gas containing silane, diborane, methane, helium and hydrogen. The data obtained show that the films produced exhibit good optoelectronic properties and show a surface morphology dependent on the filament temperature and hydrogen dilution. The increase in the filament temperature, keeping constant the hydrogen dilution (87%), promotes the preferential growth of the crystals in the {220} direction, giving rise to a pyramidal-like surface structure. This behaviour is observed by the SEM micrographs as well as by the micro-Raman and X-ray diffraction analyses. On the other hand, using a constant filament temperature, the increase in the hydrogen dilution contributes to an increase in both {111} and {220} diffraction peaks. Thus, by combining both filament temperature and hydrogen dilution the film surface can be controlled from a smooth to a pyramidal-like structure, without decreasing the crystalline fraction of the films. The structure and morphology is also reflected in the stability of the electrical dark conductivity. We observe that this property depends on the temperature range of the measurements and on the exposition time of films to the atmospheric conditions. © 2002 Elsevier Science Ltd. All rights reserved.

The aim of this paper is to present a set of electric data concerning the performances before and after ageing of Cu-Sn-Cu joins used to solder power diodes and to compare the results achieved with the ones obtained in diodes soldered using the conventional technology. The set of results achieved show that the Cu-Sn-Cu joins present even better performances than the ones exhibited by diodes soldered using the conventional technology, without requiring the use of Mo discs to be inserted between the silicon crystal and the metal contacts (stud or finger) to compensate thermal mismatches.

In this paper we present an improved version of large area (5 mm × 80 mm) flexible position sensitive detectors deposited on polyimide (Kapton® VN) substrates with 75 μm thickness, produced by plasma enhanced chemical vapor deposition (PECVD). The structures presented by the sensors are Kapton/ZnO:Al/(pin)a-Si:H/Al and the heterostructure Kapton/Cr/(in)a-Si:H/ZnO:Al. These sensors were characterized by spectral response, photocurrent dependence as a function of light intensity and position detectability measurements. The set of data obtained on one-dimensional position sensitive detectors based on the heterostructure show excellent performances with a maximum spectral response of 0.12 A/W at 500 nm and a non-linearity of ±10%. © 2002 Elsevier Science B.V. All rights reserved.

PbZrxTi1-xO3 (PZT) films are currently being investigated in view of their large switching polarization and piezoelectric coefficients useful for various applications. Besides, PZT films possess large photosensitivity, which, in combination with the above listed properties, can be a base for future microelectronic applications including photostrictive actuators and optical storage devices. In this work, PZT thin films of several compositions (x=0.2 and 0.45) were deposited on Pt-coated Si and ITO/glass substrates via modified sol-gel technique. Microstructures of the films were evaluated using XRD, SEM and AFM. The optical transmission measurements on PZT films deposited on ITO/glass revealed a high transparency over 80% and a band gap of about 3.4 eV. The observed photocurrent exhibited a maximum and was attributed to band-to-band optical transitions.

Aqueous suspensions of cordierite-based glass ceramics were prepared by using four types of dispersants and binders and different solids loading. The experiments were designed according to the Taguchi method, which shows great advantages in optimising more than two factors that need to be considered in an experimental design. Different parameters such as the type and concentration of the dispersants and the binders, and the solids loading were optimised to obtain homogeneous and crack-free green tapes. Dolapix CE 64 (1.0 wt.%) and Duramax B-1080 or Duramax B-1070 (10 wt.%) with 65 wt.% solids loading represent an optimal selection of the parameters to obtain low viscosity suspension, and crack-free green tapes with the highest green and sintered density. Microstructural differences between crack-free and cracked samples were observed by scanning electron microscopy (SEM). The crack-free green tapes show homogenous microstructures from top to bottom with organic additives uniformly surrounding the powders, whereas cracked samples exhibit heterogeneous microstructures and non-uniform distribution of the organics. © 2002 Elsevier Science B.V. All rights reserved.

Position sensitive detectors (PSD) using hydrogenated amorphous silicon as the active layer have been widely proposed either with the p-i-n or the Schottky structure. In this case, the devices are tailored to respond to light in the range 620-650 nm. Little is known about the use of silicon carbide active layers in such devices, which is important when the detected light is in the blue region of the light spectrum. In this paper we present for the first time the electro-optical properties of the a-Six:C1-x:H/Pd and p-ic-n PSD, using a-Six:C1-x:H layers deposited by plasma enhanced chemical vapour deposition (PECVD). These sensors are able to distinguish the wavelength of the impinging visible radiation (from red to blue light). In addition, the sensors respond to light intensities as lower as 1 × 10-6 W cm-2 with a resolution better than 0.04 mm and a linearity between ±0.12% and ±0.8%. © 2002 Elsevier Science B.V. All rights reserved.

In this work, we report the electro-optical properties exhibited by ZnO:A1 thin films deposited by r.f. magnetron sputtering. The effect of the deposition parameters on the properties of the films were studied with the aim to determine the most suitable deposition conditions to obtain ZnO:Al thin films with a low resistivity and high transmittance, characteristics required for applications on optoelectronic devices. After annealing, the ZnO:Al thin films present a low resistivity (6.25 × 10-3 Ωcm) and a high transmittance (90%) when produced with a deposition pressure of 1.6 × 10-2 mbar and r.f. power of 150W. © 2002 Elsevier Science Ltd. All rights reserved.

The room temperature ozone sensing properties of polycrystalline undoped zinc oxide (ZnO) thin films have been investigated. ZnO thin films have been produced by the d.c. and r.f. magnetron sputtering technique as well as with spray pyrolysis with a variety of parameters. The as-grown films were brought to a high conducting state through a reversible photoreduction process by UV light exposure and were subsequently exposed to ozone resulting in a strong resistivity increase caused by re-oxidation. The magnitude of the effect was largest for the sputtered films, which exhibited resistivity changes of more than 8 orders of magnitude, whereas films deposited by spray pyrolysis showed changes of less than 3 orders of magnitude. XRD and AFM analysis of the films revealed that all films were microcrystalline. The film texture, however, was strongly related to the growth technique and the parameters used. Best results were achieved with r.f.-sputtered films, which have been deposited at high total pressures. These films exhibited a sensor response of 1.2 × 108. © 2002 Elsevier Science B.V. All rights reserved.

In this work we studied the influence of hydrogen dilution, rf power, and the filament and substrate temperatures on the electro-optical properties and composition of a-Si:H films produced by hot wire plasma assisted technique. The a-Si:H films were produced on Mylar substrates with growth rate of up to 37 Å/s, ημτ product of 1.6 × 10-7 cm2/V, photoconductivity to dark conductivity ratio of 1 × 104 (at AM1.5 radiation), and a dark conductivity of about 10-10 (Ω cm)-1 for substrate temperature of 130 °C, hydrogen dilution of 99%, filament temperature of 1700 °C, and rf power of 100 W. © 2002 Elsevier Science B.V. All rights reserved.

The most common techniques used to produce ZnO thin films are the spray pyrolysis and the magnetron sputtering techniques, low and high cost processes respectively. The aim of this work is to compare the properties of the films produced by these two techniques. The predominant difference observed was on the morphological properties. The films produced by spray pyrolysis have a rougher surface than the ones obtained by sputtering. Also the effect of the thermal annealing treatment is much more prononnced for the ZnO thin films produced by spray pyrolysis. After heat treatment films exhibit similar electrical properties and their application to optoelectronic devices is demonstrated.

This work deals with the study of the role of intra-gap density of states on the colour selection of the collection spectrum of glass/ITO/a-Six:C1-x:H/Al Schottky photodiodes. In order to optimise the voltage colour selection and to study the influence of intragap density of states in the final device performances, different undoped a-Six:C1-x:H films (1 μm thick) have been produced in a conventional Plasma Enhanced Chemical Vapour Deposition (PECVD) system using silane and a controlled mixtures of silane and methane as gas sources. The properties of the films were analysed by dark conductivity measurements, infrared spectroscopy, visible spectroscopy and constant photocurrent method (CPM), to determine the valence controllability and to correlate the silicon carbide layer composition with the performances of the devices. The performances obtained concerning the spectral response of the devices were correlated with the carbon content and the density of states of the a-Six:C1-x:H films.

In this work, we study the influence of the hydrogenated amorphous silicon (a-Si:H) surface treatment on the J-V characteristics of a-Si:H/Pd Schottky barrier photodiodes. The a-Si:H surface were etched, thermally oxidised and wet oxidised by H2O2. The a-Si:H films were characterised by spectroscopic ellipsometry, were we found that all the oxidation techniques promote an increase of the surface oxide thickness that was confirmed by the increase of the barrier height. The highest barrier was achieved by the H2O2 oxidation where a value of 1.17 eV was found. As a result of the barrier height increase, the dark reverse current density decreases up to 10-10 A/cm2 and the signal to noise ratio increases up to 106. The open circuit voltage under AM1.5 illumination conditions also increases from 0.4 to 0.5 V. These results reveal the importance of the a-Si:H surface preparation prior to metallization to improve the Schottky photodiodes properties. © 2002 Elsevier Science B.V. All rights reserved.

In this work we present the current/voltage characteristics of Si:H/Pd Schottky structures using high quality, low defect density amorphous silicon (a-Si:H) deposited by a non-conventional, modified triode PECVD method. This new configuration allows the deposition of compact and high quality a-Si:H with a photosensitivity of 107, yielding films with low bulk defects. AFM measurements also revealed that these films have a very smooth surface allowing a low defect interface between the metal and the a-Si:H. As a result, we show that by using these a-Si:H films and by proper control of the i-layer thickness the reverse dark current of the diode can be highly reduced achieving signal to noise ratio of 106, surpassing the results usually achieved by p-i-n structures.

This paper deals with the growth process of nanostructured silicon films produced by chemical vapour deposition technique, at or close to the γ-regime where powders are formed. There, besides the set of chemical reactions undertaken by the species decomposed on the growth surface, the importance of the physics of the plasma in managing the powders and on the final film performances will be shown. To identify the plasma region where Si nanoaggregates are formed, we propose the use of a new parameter that translates the energy coupling of the rf power to the species of the gas flow, per pressure range of the process. By doing so we could establish an excellent correlation between this ratio and the plasma parameters such as peak to peak rf voltage and plasma impedance, or with the films defect density and their transport properties. Apart from that, we also show that high compact Si nanoclusters could be grown under moderate ion bombardment. Finally, to allow the growth at high rates of controlled silicon nanostructures, a three cycling process based on hot wire chemical vapour deposition and plasma assisting the hot wire technique will be discussed. © 2002 Elsevier Science Ltd. All rights reserved.

Currently, microactuators are being developed using shape memory alloys (SMAs), which allow simple design geometries and provide large work outputs in restricted space. Several techniques have been used to produce NiTi shape memory alloy thin films, but from the practical point of view, only the sputter deposition method has succeeded so far. Vacuum evaporation of NiTi binary alloy entails the potential problem of the evaporation rates of each component not being the same due to differences in vapour pressure. Aiming to study the possible applications of SMAs to microfabrication, NiTi thin films were produced at CENIMAT by sputter and vacuum evaporation using raw materials from different sources. The films were analysed by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) at room temperature, as well as in situ high temperature, in order to characterise the temperature ranges at which the different structural transformations occur. © 2002 Elsevier Science B.V. All rights reserved.

In this work, we present a study of the effect of temperature, type and concentration of the dopant on the structural characteristics of ZnO thin films produced by spray pyrolysis; the crystallite size has been determined from profile peak shape analysis. These results are compared to the electrical characterisation performed on these materials. The effect of the dopant on the properties of ZnO thin films depends on its characteristics, mainly its ionic radius. Al, Ga and In have been studied as dopants, the best one being In, since it leads to the lowest resistivity.

Hall effect measurements are one of the most powerful techniques for obtaining information about the conduction mechanism in polycrystalline semiconductor materials, which is the basis for understanding semiconductor gas sensors. In order to investigate the correlation between the microscopic characteristics and the macroscopic performances exhibited by undoped tin oxide gas sensors deposited by spray pyrolysis, Hall effect measurements were performed at different temperatures, from room temperature up to 500 K, and in the presence of two different atmospheres, air and methane. From these measurements, it was possible to infer the potential barrier and its dependence with the used atmosphere. The obtained results were analysed in terms of the oxygen mechanism at grain boundaries on the basis of the grain boundary-trapping model. In the presence of methane gas, the electrical resistivity decreases due to the lowering of the inter-grain boundary barrier height.

The surfaces of cordierite and glass particles were modified by coating them with an alumina precursor using a precipitation process in the presence of urea. Scanning electron microscopy (SEM), high-resolution transmission electron microscopy, X-ray diffraction, electrophoresis, and rheological measurements were used to characterize the coated powders. SEM and transmission electron microscopy morphologies of the coated powders revealed that amorphous and homogeneous coatings have been formed around the particles. The morphology of the coated powders showed a coiled wormlike surface. The coating Al2O3 layer dominated the surface properties of the coated glass and cordierite powders. The influence of the coating layer on the processing ability of cordierite-based glass-ceramics substrates by tape casting was studied in aqueous media. It could be concluded that the coating of the powders facilitates the processing and yields green and sintered tapes with denser, more homogeneous microstructures compared with the uncoated powders.

In this paper, we present the optical, electrical, structural and mechanical properties exhibited by aluminum-doped zinc oxide (ZnO:Al) thin films produced by RF magnetron sputtering on polymeric substrates (polyethylene terephthalate, PET; Mylar type D from Dupont®) with a standard thickness of 100 μm. The influence of the uniaxial tensile strain on the electrical resistance of these films was evaluated in situ for the first time during tensile elongation. In addition, the role of the thickness on the mechanical behavior of the films was also evaluated. The preliminary results reveal that the increase in electrical resistance is related to the number of cracks, as well as the crack width, which also depends on the film thickness. © 2002 Elsevier Science B.V. All rights reserved.

Aluminium doped zinc oxide thin films (ZnO:Al) have been deposited on polyester (Mylar type D, 100 μm thickness) substrates at room temperature by r.f. magnetron sputtering. The structural, morphological, optical and electrical properties of the deposited films have been studied. The samples are polycrystalline with a hexagonal wurtzite structure and a strong crystallographic c-axis orientation (002) perpendicular to the substrate surface. The ZnO:Al thin films with 85% transmittance in the visible and infra-red region and a resistivity as low as 3.6×10-2 Ωcm have been obtained, as deposited. The obtained results are comparable to those ones obtained on glass substrates, opening a new field of low cost, light weight, small volume, flexible and unbreakable large area optoelectronic devices.

In order to correlate the MIS devices performance with different surface oxidation methods, AFM, spectroscopic ellipsometry and infrared spectroscopy measurements were performed in a-Si:H films, before and after surface oxidation, using different oxidation techniques and oxides: thermal dry (in air), wet (in H2O2) and by oxygen plasma, while MIS (metal-insulator-semiconductor) devices were characterized by I-V curves, under dark and AM1.5 illumination conditions. The a-Si:H films were grown by the PECVD technique, in a modified triode configuration reactor to allow a precise control of the ion bombardment during the film deposition. We found that the growth of a thin layer of oxide by chemical processes on the top of the a-Si:H surface can cause changes on the surface morphology that are reflected in the electrical behaviour of the devices. The oxygen plasma treatment, cause the rearrangement of the surface atoms leading to a change of their morphology and to the improvement of the electrical properties of the surface for a MIS applications.