Carlos Chastre

Com o crescente consumo de energia elétrica são cada vez mais os países que procuram fontes de energia renovável e limpa, entre elas a eólica. A quantidade de energia produzida é influenciada pela altura das torres, dimensões das pás e potência dos aerogeradores. Quanto maior for a elevação da turbina maiores são a velocidade e estabilidade dos ventos alcançados. A solução de torre treliçada em concreto armado pré-moldado idealizada por Lúcio e Chastre [2] permite a construção de torres altas e é competitiva em relação aos outros sistemas estruturais.As ligações têm uma importância fundamental no comportamento global das estruturas pré-moldadas. A viabilidade da ligação (fácil execução, baixo custo, comportamento/capacidade resistente) é preponderante na viabilização da construção destas torres.Até à data foram estudadas quatro ligações (S1, S2, S3 e S4), sendo neste artigo abordadas apenas as ligações do modelo S3 com junta de 3mm (barras salientes/bainhas corrugadas/selagem com grout) e do modelo S4 com junta de 50 mm (ligações aparafusadas produzidas comercialmente).Através dos resultados experimentais pode-se concluir que o mecanismo de rutura foi o mesmo nos dois modelos e que as soluções estudadas preenchem os requisitos para a sua utilização em estruturas pré-moldadas de concreto armado para suporte de aerogeradores.

This paper presents a comparative evaluation of efficiencies of different accelerated ageing tests (freezethaw, thermal shock, salt crystallization, dissolution and wetting-drying) and fuzzy inference system in predicting weathering degrees of some monument stones from three historical sites (Anahita Temple, Anobanini reliefs and Eshkaft-e Salman reliefs, Iran). The combined effects of natural weathering processes (heating and cooling, wetting and drying, and freezing and thawing) and climatic information were used for assessing the natural weathering degrees. Finally, the natural weathering degrees were multiplied by time effect coefficients to obtain more realistic natural weathering degrees of the monuments. The predicted natural weathering degrees for Anahita Temple, Anobanini reliefs and Eshkaft-e Salman reliefs are 56%, 61%, and 47%, respectively. These predicted values reasonably support the weathering degrees defined by progressive decay indices (calculated equal to 2.77, 3.42 and 2.66 for Anahita Temple, Anobanini reliefs and Eshkaft-e Salman reliefs, respectively), which means the fuzzy model potentially could accurately predict the weathering of stones.

Gravity loads can affect a reinforced concrete structure’s response to seismic actions, however, traditional procedures for testing the beam behaviour do not take this effect into consideration. An experimental campaign was carried out in order to assess the influence of the gravity load on RC beam connection to the column subjected to cyclic loading. The experiments included the imposition of a conventional quasi-static test protocol based on the imposition of a reverse cyclic displacement history and of an alternative cyclic test procedure starting from the gravity load effects. The test results are presented, compared and analysed in this paper. The imposition of a cyclic test procedure that included the gravity loads effects on the RC beam ends reproduces the demands on the beams’ critical zones more realistically than the traditional procedure. The consideration of the vertical load effects in the test procedure led to an accumulation of negative (hogging) deformation. This phenomenon is sustained with the behaviour of a portal frame system under cyclic loads subject to a significant level of the vertical load, leading to the formation of unidirectional plastic hinges. In addition, the hysteretic behaviour of the RC beam ends tested was simulated numerically using the nonlinear structural analysis software – OpenSees. The beam–column model simulates the global element behaviour very well, as there is a reasonable approximation to the hysteretic loops obtained experimentally.

The aim of the present paper is to evaluate the gravity loads effect in the behaviour of reinforced concrete beams critical zones subjected to cyclic loads. A numerical study to assess the influence of gravity load on RC beam critical zones subjected to cyclic loading is presented, assuming the level of gravity load as a variable parameter. For this purpose, the non-linear model was previously validated with an experimental campaign carried out on RC beam connection subject to cyclic loading with and without gravity loads. The consideration of the gravity load effects led to an accumulation of negative (hogging) deformation and the formation of an unidirectional plastic hinge. In order to validate this behaviour in an overall structural response, a non-linear numerical analysis of a RC frame system under cyclic loads, subject to different levels of gravity load, is also presented. The numerical results are analysed in terms of global hysterical response, accumulated energy dissipation and equivalent viscous damping ratio. In this numerical study was observed that the hysteretic response depends on the load path. In the presence of higher gravity loads levels, the structure hysteretic behaviour exhibits higher damage levels and the failure mechanism is prone to the formation of four plastic hinges. This phenomenon is analysed and discuss in the present paper. © Federation Internationale du Beton (fib) - International Federation for Structural Concrete, 2019.

Neste artigo é apresentado um resumo das intervenções de conservação realizadas no século passado na Igreja de São Leonardo, bem como um resumo dos estudos realizados na última década. Em seguida mostra-se o padrão de degradação que ocorre nos portais de arenito da igreja e é analisada a evolução da alveolização que ocorreu nos portais de arenito ao longo dos últimos sessenta a setenta anos. No final, a inspeção visual dos portais de arenito é comparada com um levantamento realizado através de varrimento por laser tridimensional.

Neste artigo é apresentado um resumo das intervenções de conservação realizadas no século passado e dos estudos e testes não destrutivos realizados na última década na Igreja de São Leonardo na Atouguia da Baleia. Em seguida mostra-se o padrão de degradação que ocorre nos portais de arenito da igreja e é analisada a evolução da alveolização que ocorreu nos portais de arenito ao longo dos últimos sessenta a setenta anos. No final, a inspeção visual dos portais de arenito é comparada com um levantamento realizado através de varrimento por laser 3D.

The main goal of the present research work is to characterise a unidirectional fibre reinforced grout (UFRG), developed as an alternative material to strengthen RC structures using small thickness jacketing. A high performance cementitious grout reinforced with continuous and unidirectional non-woven steel fibre mat has been developed for this purpose. It was expected that the optimization of the percentage and alignment of the steel fibres would yield a more efficient fibre grout. In fact, the composite should attain higher tensile strength with continuous fibres since the fibre embedment length is enough to prevent fibre pull-out. An experimental programme was carried out to characterise the UFRG’s mechanical properties. Compressive tests were conducted on small thickness tubular specimens to enable the determination of the compressive strength and the static modulus of elasticity. The tensile strength was obtained from splitting tests performed on cubic specimens (DIN 1048-5). Semi-empirical equations, based on the experimental results, are proposed to estimate UFRG’s modulus of elasticity, compressive strength and tensile strength. Two strengthening solutions for RC structures using small thickness CFRP jacketing are presented.

The present work studies the behaviour of bonded steel plates to reinforced concrete elements, which can be used in the strengthening of concrete structural elements. Metallic expansion bolts can be added.The objective of this dissertation is to investigate the behaviour to monotonic actions and particularly to cyclic loading of steel-epoxy-concrete connection with expansion bolts. This cyclic action is of particular interest due to the strong seismicity of the Portuguese territory.The research is mainly based in experimental analysis. The caracterization of the materials was carried out. Six models of the steel-epoxy connection were tested with monotonic loading. Twenty six models of steel-epoxy-concrete bond were submitted either to monotonic or to cyclic actions.Besides the type of action, other parameters were studied in the steel-epoxy-concrete connection models.These were the bond geometry area, the type of concrete, the type of epoxy and connection - with or without metallic expansion bolts.A parametric study with a numerical model of finite elements, as well as a global analysis of the experimental tests of the steel-epoxy-concrete connection was carried out.

n/a

A demanda de energia, faz com que o homem esteja sempre a procura de novas soluções para a sua produção. Uma opção é a energia eólica, por se tratar de uma energia limpa, renovável e inesgotável. Para se evitar a ocupação das terras férteis, é natural a busca de soluções no mar. Portanto, neste trabalho é estudado o comportamento estrutural dinâmico de uma torre treliçada em concreto armado pós-tensionado por tirantes externos idealizada para uso offshore com a finalidade de suporte para turbinas eólicas de eixo horizontal. A torre está sujeita às ações gravitacionais, aerodinâmicas e hidrodinâmicas. Para considerar estas ações desenvolveu-se um código computacional específico usando a linguagem MATLAB. É proposto um modelo simplificado para análise bi-dimensional, utilizando-se elementos de pórtico plano com a finalidade de contornar as dificuldades de uma análise tridimensional. Embora específico para este tipo de torre, o codigo permite variar geometrias, carregamentos e alterações do nível do mar. Nas cargas aerodinâmicas élevado em conta o espectro de Von Karman. As cargas hidrodinâmicas são avaliadas pela equação de Morison. As cargas nodais equivalentes são determinadas por integração ao longo do elemento estrutural de acordo com o proposto por Souza. Os tirantes pós-tensionados são monitorados para não sofrerem esforços de compressão. A análise é realizada no domínio do tempo utilizando-se o algoritmo de integração de Newmark.. Através dos procedimentos adotados foi possível obter resultados para as freqüências, deslocamentose esforços, que se mostraram coerentes com os obtidos por modelos tri dimensionais mais complexos. O código desenvolvido permitiu a análise de forma simples, eficiente e confiável de torres treliçadas de concreto armado.

Cement bonded particle board (CBPB) is a composite material produced in plates consisting mainly of wood and cement, and may contain additives. This material is currently used in cladding, raised floors, dropped ceilings, prefabricated houses, office containers and various supplies to the building industry such as kitchens, bathrooms and furniture. It is composed of a type of wood Pinus pinaster and/or Pinus pinea, Portland cement type II, sodium silicate and aluminium sulphate. CBPB has been the subject of several studies with the purpose of enabling the use of other types of wood or even vegetable biomass, as the chemical compounds from wood (extractives and sugars) tend to inhibit of cement hydration. A study on the behaviour of short CBPB elements under compression was carried out in the Department of Civil Engineering of Universidade NOVA de Lisboa with the aim of enabling its use in structural elements. The study was supported by VIROC, the company which produces CBPB in Portugal. This paper presents and analyses the most significant results of a campaign of axial compression tests performed on 111 specimens of different heights and cross sections. The behaviour of CBPB specimens of varying slenderness was subjected to a more detailed analysis.

Sandstones are very important in the building elements of world’s historical and cultural heritage. The façades of St. Leonard’s church in Atouguia da Baleia village in western region of Portugal are an outstanding example of the effect of alveolization on going for several centuries. In Middle ages there was an harbour and a sodium chloride rich environment near this church was responsible for this significant stone degradation pattern.
A new approach of consolidating products application on stone walls façades based on Karsten pipe using total head to allow full absorption of stone was followed.
Experimental research, based on physical and mechanical tests, was carried out on selected representative samples of a variety of sandstones on monuments treated with ethyl silicates in order to assess the effectiveness and harmfulness of these treatments.
The comparison of results between traditional immersion applications and Karsten pipe’s based procedure on stone monument indicate the potential viability of this new approach when difficult conditions of consolidating products’ absorption occurs on stone monuments.

Abstract Sandstones are widely used in the building elements of the world’s stone monuments. Alveolization due to salt crystallization-dissolution is the most important degradation pattern found on the Middle Ages’ sandstone façades of St. Leonardo’s Church in Portugal. An outstanding case of widespread distribution of deep and large alveolization patterns found mainly on portals and vaults of its sandstone façades appeared as a result of the past and present proximity of the seashore. On stonewall façades, a new approach of consolidating products’ treatments using the total head was followed in order to allow full absorption of stone. Physical and mechanical tests were carried out on selected representative specimens of varieties of sandstones on the monument. Treatments with ethyl silicates were assessed by means of its effectiveness, harmfulness, and durability. The comparison of results between the application of this new procedure on this stone monument and the traditional intervention treatments highlighted the potential viability of the former to overcome difficult conditions of absorption of consolidating products.

Weathering imposes vital effects on stony monuments. Mostly, the degree of weathering is determined by simple test results, ignoring simultaneous effects of various weathering factors. Hence, the main purpose of this study is to develop prediction models with fuzzy inference systems to determine the weathering degree of the Persepolis stone, using various accelerated ageing tests in laboratory condition and to extrapolate the results to the natural condition, considering climatic information. The results suggest reliable conformity between the prediction of the weathering degree of the stone and the weathering degree observed in the Persepolis complex in natural condition.

This paper deals with the coupled effect of temperature and silica fume addition on rheological, mechanical behaviour and porosity of grouts based on CEMI 42.5R, proportioned with a polycarboxylate-based high range water reducer. Preliminary tests were conducted to focus on the grout best able to fill a fibrous network since the goal of this study was to develop an optimized grout able to be injected in a mat of steel fibers for concrete strengthening. The grout composition was developed based on criteria for fresh state and hardened state properties. For a CEMI 42.5R based grout different high range water reducer dosages (0, 0.2%, 0.4%, 0.5%, 0.7%) and silica fume (SF) dosages (0, 2%, 4%) were tested (as replacement of cement by mass). Rheological measurements were used to investigate the effect of polycarboxylates (PCE) and SF dosage on grout properties, particularly its workability loss, as the mix was to be injected in a matrix of steel fibers for concrete jacketing. The workability behaviour was characterized by the rheological parameters yield stress and plastic viscosity (for different grout temperatures and resting times), as well as the procedures of mini slump cone and funnel flow time. Then, further development focused only on the best grout compositions. The cement substitution by 2% of SF exhibited the best overall behaviour and was considered as the most promising compared to the others compositions tested. Concerning the fresh state analysis, a significant workability loss was detected if grout temperature increased above 35°C. Below this temperature the grout presented a self-levelling behaviour and a life time equal to 45 minutes. In the hardened state, silica fumes increased not only the grout’s porosity but also the grout’s compressive strength at later ages, since the pozzolanic contribution to the compressive strength does not occur until 28 days and beyond.

The façades of St. Leonard’s church and the castle in Atouguia da Baleia village in western region of Portugal are monuments built in Middle Ages. Significant stone degradation patterns are visible, being the alveolization an outstanding case study.The more porous type of sandstones similar to the variety found in the vernacular architecture of Atouguia da Baleia was treated with ethyl silicates. In order to allow the study of the durability of these conservation treatments, accelerated artificial ageing salt crystallization tests were carried out and an automatic ageing chamber was developed.Physical and mechanical behaviour was assessed on consolidated specimens before and after accelerated artificial ageing salt crystallization tests. The authors propose a prediction of the durability of these consolidation treatments by means of the salt crystallization ageing results.

n/a

Experimental research was carried out about into ethyl silicate applications on sandstone samples. Consolidation was assessed by drilling strength, impregnation depth and also monotonic and cyclic uniaxial compressive tests in order to evaluate the compressive mechanical behaviour of treated sandstone. The stress–strain compression diagrams showed a significant increase in the values of mechanical parameters after consolidation treatments. The difference in compressive strength values between monotonic and cyclic compression disappears after the consolidation treatments. An equation of consolidation effect was obtained from an analytical model by means of compressive behaviour assessed by stress–strain diagrams. These sandstone samples have values of porosity similar to the more weathered variety of sandstone found in facades of monuments in the village of Atouguia da Baleia, in the western region of Portugal. The most important degradation pattern found on sandstone building stones is alveolization caused by salt crystallization since the Middle Ages.

Sandstone building stones are important in the building elements of Portuguese monuments, particularly in the western and southern regions. Alveolization due to salt crystallization was the most important degradation pattern found in the old sandstone façades of buildings in the village of Atouguia da Baleia. Because weathering progressively increases porosity in stones, experimental research was conducted on the most porous variety of sandstone, which is similar to the type of stones found in the façades of ancient buildings in that village. An automatic salt crystallization accelerated ageing chamber was developed. Monotonic and cyclic uniaxial compressive tests were carried out on samples after sodium chloride crystallization ageing tests had been performed, in order to assess the compressive mechanical behavior of sandstone during accelerated ageing. The results of stress–strain compression diagrams showed a clear decreasing trend in the values of mechanical parameters during the salt crystallization ageing progress. The difference in compressive strength values between monotonic and cyclic compression also decreases with as salt crystallization ageing progresses. A predictive equation that correlates the compressive strength of sandstones with salt crystallization ageing cycles is proposed.

Ao longo da sua vida útil os edifícios históricos estão sujeitos a alterações de uso, a agentes ambientais e a diferentes ações como assentamentos do solo, incêndios, inundações ou sismos, para os quais podem não estar preparados. Além disso, a falta de manutenção contínua ajuda a colocar grande parte desse património em risco devido a problemas estruturais que reduzem sua própria segurança e a dos seus utilizadores. A preservação e mitigação de riscos do património cultural construído requer o uso de ferramentas confiáveis, a fim de avaliar o seu estado de conservação e identificar e prevenir potenciais vulnerabilidades. Os testes destrutivos tradicionais não são possíveis de realizar na maioria dos edifícios históricos, por isso é necessário selecionar testes não destrutivos (NDT) que permitam a caracterização física e mecânica dos materiais e do comportamento da estrutura. Neste artigo apresenta-se uma visão geral de diferentes equipamentos e testes NDT que permitem o levantamento geométrico e o mapeamento dos danos do edifício, a análise petrográfica da pedra de alvenaria, a caracterização das propriedades físicas e mecânicas dos materiais e o comportamento estrutural do edifício.

A indústria do betão pré fabricado é, por tradição, inovadora, precursora de novas tecnologias e de novos materiais.O processo produtivo de estruturas com elementos pré-fabricados difere significativamente do das estruturas betonadas em obra pelo facto de uma parte, ou a totalidade, dos elementos da estrutura serem produzidos em fábrica, em condições de produção melhoradas em relação às condições da obra, e serem posteriormente transportados para a obra, onde são, finalmente ligados entre si. A produção em fábrica é efectuada em ambiente protegido do Sol e da chuva, com operários fixos e com formação profissional para desenvolverem tarefas com procedimentos normalizados. Consequentemente, os elementos executados em fábrica possuem melhor qualidade, sob vários aspectos, do que as estruturas executadas em obra.Este livro divide-se em duas grandes áreas, numa primeira abordam-se algumas aplicações de estruturas pré-moldadas no mundo e numa segunda parte descreve-se o seu comportamento estrutural face a diferentes acções. Nos primeiros capítulos relata-se a experiência da pré-fabricação em três países de diferentes continentes: o Brasil, Portugal e a Austrália e revelam-se novas oportunidades que poderão surgir para a indústria da pré-fabricação. Nos capítulos seguintes dá-se um especial enfoque à investigação do comportamento das ligações (rígidas e semi-rígidas). Aborda-se o projecto de estruturas de betão pré-fabricado às acções acidentais. E por fim, dedicam-se os últimos capítulos ao comportamento das estruturas pré-fabricadas face às acções sísmicas. Nesta área, o bom desempenho das estruturas e grande parte do conhecimento e da tecnologia actual advém da resposta dada pelos engenheiros, investigadores e construtores aos fenómenos naturais que afectam as nossas construções, como comprova o desempenho das ligações dúcteis resistentes a momentos em edifícios pré fabricados de betão no verdadeiro teste sísmico que foram os sismos de Christchurch de 2010 e 2011.

The wind energy production is a growing industry and the energy produced is renewable and environmentally cleaner than most of the other systems. The towers to support the wind energy generators may be built with precast concrete elements that are competitive in comparison to other structural systems. The evolution of the technology for wind energy production shows a clear need for larger wind turbines and longer blades and, consequently, taller towers, where precast concrete solutions are competitive. Truss precast concrete towers is a solution that complies with the demands of the present and future wind energy production. The research on the execution and structural behaviour of the connections between the tower elements is an important issue. This communication presents the experimental analysis of column to column connections for precast concrete towers. The tests included connections with commercial threaded bars welded to the rebars and connections with grouted corrugated steel sleeves. Thick joints (50 mm) filled with fibre reinforced grout and thin joints (3 mm) filled with epoxy resin were tested and analysed.

During the last years several projects and studies have improved the knowledge about Textile Reinforced Mortar (TRM) technology. TRM has already been used in strengthening masonry and reinforced concrete structural elements such as walls, arches, columns and beams. This material is presented as a real alternative to the use of fibre-reinforced polymers (FRP) in situations where these composites have presented some drawbacks or their use is banned. Textile Reinforced Mortar show a complex mechanical behaviour derived from the heterogeneity of the constituent materials. This paper aims to deepen the knowledge of this composite material in terms of tensile behaviour. Following this scope, this paper presents an experimental campaign focused on thirty one TRM specimens reinforced with four different reinforcing ratios. The results are analysed and contrasted with two distinct models. i) the Aveston-Cooper-Kelly theory (ACK) which is based on a tri-linear analytical approach; and ii) a nonlinear numerical simulation with a 3D Finite Element code. The Finite Element Analysis (FEA) of the TRM tensile tests also showed no significant dependence on the basalt-to-mortar interface, i.e., the choice of a bond-slip curve in order to reproduce the bond stresses and slippages along the interface is irrelevant and it can be simply considered as rigid interface.

Os compósitos de FRP podem descolar prematuramente da superfíce de betão, isto é, antes de esgotada a sua resistência elástica. Esta situação é mais provável se não forem tidos em conta factores como o tipo de preparação da superfície, a exposição a acção ambiental severa, e a resistência do próprio betão. Com o objectivo de analisar a influência de parte destes factores no desempenho da ligação compósito de fibra de vidro (GFRP) e betão, empreendeu-se uma campanha experimental baseada em ensaios de corte duplo. Os resultados permitiram determinar e comparar as forças máximas transmitidas ao GFRP e tensões de aderência máxima para diferentes tratamentos de superfície e condições de envelhecimento. Foram também determinadas aproximações para curvas de tensão de aderência vs. deslizamento (bond-slip). Os resultados obtidos são contrastados com resultados obtidos por modelação numérica.

Since the 1980’s, several buildings throughout the world have been subject to gas explosions, impact by cars or airplanes, or car bomb attacks. In many cases the effect of the impact or explosion has been the failure of a critical structural member at the perimeter of the building. After the failure, the load supported by that member could not be redistributed and part or all of the structure has collapsed in a progressive manner. The phenomenon that occurs when local failure is not confined to the area of initial distress, and spreads horizontally and/or vertically through the structure, is termed progressive collapse.

Progressive collapse is a relatively rare event, as it requires both an accidental action to cause local damage and a structure that lacks adequate continuity, ductility, and redundancy to prevent the spread of damage. It is technically very difficult and economically prohibitive to design buildings for absolute safety. However it is possible to construct precast concrete buildings that afford an acceptable degree of safety with regard to accidental actions.

A structure is normally designed to respond properly, without damage, under normal load conditions, but local and/or global damages cannot be avoided under the effect of an unexpected, but moderate degree of accidental overload. Properly designed and constructed structures usually possess reasonable probability not to collapse catastrophically under such loads, depending on different factors, for example: the type of loading; the degree and the location of accidental loading in regard to the structure and its structural members; the type of structural system, the construction technology, and the spans between structural vertical members, etc.

No structure can be expected to be totally resistant to actions arising from an unexpected and extreme cause, but it should not be damaged to an extent that is disproportionate to the original cause.

The aim of fib Bulletin 63 is to summarize the present knowledge on the subject and to provide guidance for the design of precast structures against progressive collapse. This is addressed in terms of (a) the classification of the actions, (b) their effect on the structural types, (c) the strategies to cope with such actions, (d) the design methods and (e) some typical detailing, all supplemented with illustrations from around the world, and some model calculations.

In 1994 fib Commission 6: Prefabrication edited a successful Planning and Design Handbook that ran to approximately 45,000 copies and was published in Spanish and German.Nearly 20 years later Bulletin 74 brings that first publication up to date. It offers a synthesis of the latest structural design knowledge about precast building structures against the background of 21st century technological innovations in materials, production and construction. With it, we hope to help architects and engineers achieve a full understanding of precast concrete building structures, the possibilities they offer and their specific design philosophy. It was principally written for non-seismic structures.

The handbook contains eleven chapters, each dealing with a specific aspect of precast building structures.
The first chapter of the handbook highlights best practice opportunities that will enable architects, design engineers and contractors to work together towards finding efficient solutions, which is something unique to precast concrete buildings.
The second chapter offers basic design recommendations that take into account the possibilities, restrictions and advantages of precast concrete, along with its detailing, manufacture, transport, erection and serviceability stages.
Chapter three describes the precast solutions for the most common types of buildings such as offices, sports stadiums, residential buildings, hotels, industrial warehouses and car parks. Different application possibilities are explored to teach us which types of precast units are commonly used in all those situations.
Chapter four covers the basic design principles and systems related to stability. Precast concrete structures should be designed according to a specific stability concept, unlike cast in-situ structures.
Chapter five discusses structural connections.
Chapters six to nine address the four most commonly used systems or subsystems of precast concrete in buildings, namely, portal and skeletal structures, wall-frame structures, floor and roof structures and architectural concrete facades.
In chapter ten the design and detailing of a number of specific construction details in precast elements are discussed, for example, supports, corbels, openings and cutouts in the units, special features related to the detailing of the reinforcement, and so forth.
Chapter eleven gives guidelines for the fire design of precast concrete structures. The handbook concludes with a list of references to good literature on precast concrete construction.

This document has a broad scope and is not focussed on design issues. Precast construction under seismic conditions is treated as a whole. The main principles of seismic design of different structural systems, their behavior and their construction techniques are presented through rules, construction steps and sequences, procedures, and details that should lead to precast structures built in seismic areas complying with the fundamental performance requirements of collapse prevention and life safety in major earthquakes and limited damage in more frequent earthquakes.The content of this document is largely limited to conventional precast construction and, although some information is provided on the well-known “PRESSS technology” (jointed ductile dry connections), this latter solution is not treated in detail in this document.The general overview, contained in this document, of alternative structural systems and connection solutions available to achieve desired performance levels, intends to provide engineers, architects, clients, and end-users (in general) with a better appreciation of the wide range of applications that modern precast concrete technology can have in various types of construction from industrial to commercial as well as residential. Lastly, the emphasis on practical aspects, from conceptual design to connection detailing, aims to help engineers to move away from the habit of blindly following prescriptive codes in their design, but instead go back to basic principles, in order to achieve a more robust understanding, and thus control, of the seismic behaviour of the structural system as a whole, as well as of its components and individual connections.

Precast concrete sandwich panels started being used as cladding for buildings, together with the rise of industrial prefabrication, during the mid-20th century. Since then, society and industry have become increasingly aware of energy efficiency in all fields, for both affordability and sustainability consciousness. As such, buildings have been subject to increasingly stringent requirements with the technology of sandwich panels kept continually at the forefront.
Nowadays, sandwich panels have reached the highest standards of functional performance as structural efficiency, flexibility in use, the speed as well as of aesthetic appeal. These combine in building construction with the well-known advantages of prefabrication; such as construction, quality consciousness, durability and sustainability. Sandwich panels have gained more and more important in their field, thus representing quite a significant application within the industry of prefabrication and an important share of the market.
The Commission ‘Prefabrication’ is keen to promote the development of all precast structural concrete products and to transfer the knowledge to practical design and construction. Now filling a strategic gap, by issuing this Guide to Good Practice, which includes design considerations, structural analysis, building physics, use of materials, manufacturing methods, equipment, field performance, and provides a comprehensive overview of the information currently available worldwide. The Commission is particularly proud that this document is a result of close cooperation with PCI and that it will be published by both fib and PCI. This cooperation started six years ago, first with comparing the different approaches to several issues, then progressively integrating up to producing common documents, like this one, that wasn’t yet treated in a specific Guide by either body.

The aim of the present study was to proceed to a numerical analysis of the gravity load effects on the behaviour of reinforced concrete beam critical zones when subjected to cyclic loads. A parametric study to assess the influence of different levels of gravity load on RC beam critical zones subjected to cyclic loading was carried out. For this purpose, assuming the level of gravity load as a variable parameter, a nonlinear numerical model of a beam-column connection, previously calibrated with experimental data, was used. In order to evaluate the gravity load effects in the global response, a numerical study of a RC frame system is also presented. The numerical results are analysed in terms of global hysteretic response, accumulated energy dissipation and equivalent viscous damping ratio. In this numerical study, it was observed that the hysteretic response depends on the load path. In the presence of higher gravity load levels, the structure hysteretic behaviour exhibits higher damage levels, associated to a failure mechanism corresponding to the formation of four span plastic hinges. Thus, the proper test procedure should involve the imposition of a reverse cyclic displacement history starting each cycle from the gravity load effects.

A ligação pilar-fundação tem um papel fundamental no comportamento das estruturas pré-fabricadas, em particular, na presença de acções horizontais, como a acção dos sismos e do vento, que introduzem esforços elevados na base dos pilares. Um dos sistemas de ligação pilar-fundação usados em estruturas pré-fabricadas consiste em deixar na extremidade inferior dos pilares armaduras salientes que são introduzidas em negativos executados nas fundações. Estes negativos são posteriormente injectados com grout para garantir a ligação. No presente trabalho foram estudadas diferentes soluções de negativos para ligação das armaduras do pilar à fundação, tendo sido realizados ensaios monotónicos para analisar o seu comportamento. Nesta comunicação apresentam-se e discutem-se os resultados obtidos da análise experimental efectuada.

A ligação pilar-fundação tem um papel fundamental no comportamento das estruturas pré-fabricadas,
em particular, na presença de acções horizontais, como a acção dos sismos e do vento. Um dos sistemas de ligação pilar-fundação usados em estruturas pré-fabricadas consiste em deixar na extremidade inferior dos pilares armaduras salientes que são introduzidas em negativos executados nas fundações, sejam elas sapatas ou maciços de encabeçamento de estacas. Estes negativos são posteriormente injectados com “grout” para garantir a ligação. Foram estudados diferentes soluções de negativos para ligação das armaduras do pilar na fundação. Foram realizados ensaios monotónicos e cíclicos, para analisar não só o comportamento às acções estáticas mas também para a acção sísmica. No presente trabalho apresentam-se os resultados obtidos com a análise experimental efectuada. O estudo realizado permite apresentar recomendações para projecto e quais os tipos de ligações com melhor desempenho.

Os edifícios históricos como os palácios, castelos, igrejas e templos, são exemplos do património construído e constituem uma parte importante do nosso património cultural. Estas construções históricas incluem normalmente paredes de alvenaria maciça e pedra natural. A salvaguarda do património construído em pedra é de importância inquestionável, pelo que devem ser desenvolvidas e estudadas técnicas de intervenção adequadas em materiais e estruturas. Neste artigo, é apresentada uma metodologia de ensaios não destrutivos para avaliar a conservação de edifícios históricos de pedra e, com base nesta metodologia, é mostrado um caso de estudo na Igreja de São Leonardo, monumento português construído na Atouguia da Baleia no século XIII.

No património edificado português as rochas granulares assumem importância relevante nos elementos construtivos presentes no património histórico e cultural, nomeadamente as pedras graníticas e areníticas. Tendo por objectivo a avaliação do comportamento mecânico de rochas granulares presentes no património edificado histórico foi realizado um estudo de investigação experimental sobre amostras dos litótipos seleccionados e que são representativos de rochas presentes no próprio edificado, em termos de propriedades petrográficas, físicas e mecânicas. Neste artigo apresenta-se um modelo analítico definido com base em ensaios experimentais que permite efectuar a simulação do comportamento das rochas em compressão uniaxial (diagramas de tensão-deformação), função de propriedades físicas e mecânicas obtidas através de ensaios não destrutivos e quasi não destrutivos. Este modelo permite desta forma a avaliação do comportamento mecânico de rochas granulares sem afectar a integridade do património histórico.

Building stones, particularly sandstone and granite, are very important in the building elements of Portugal’s historical and cultural heritage. Experimental research, based on uniaxial compressive tests, was carried out on selected representative samples of lithotypes of rocks used in historic built heritage, with a view to evaluating the compressive mechanical behaviour of different building stones. The results showed that porosity plays a central role in the compressive behaviour of granites and sandstones. As porosity can be evaluated in field conditions with non-destructive tests it was decided to derive an analytical model to predict compressive behaviour based on the knowledge of porosity of the building stones. A cubic polynomial function was adopted to describe the pre-peak regime under compression to implement the model. Furthermore, a statistical correlation between mechanical and porosity data had to be defined. Good agreement between experimental and analytical compressive stress–strain diagrams, from which the mechanical properties like compressive strength and modulus of elasticity can be derived, was achieved.

Este trabalho apresenta o desenvolvimento de um software para análise de torres treliçadas em concreto armado, pós-tensionada por tirantes externos, com a finalidade de suporte para turbinas eólicas de eixo horizontal, em ambiente offshore. A torre está sujeita às ações gravitacionais, aerodinâmicas, hidrodinâmicas. Desenvolveu-se um código computacional, em linguagem MATLAB, específico para este tipo de torre. As dificuldades de uma análise tridimensional mais complexa foram reduzidas propondo-se um modelo simplificado bi-dimensional utilizando-se elementos de pórtico plano. As cargas de vento são variadas segundo o espectro de von Karman. Para as ondas marítimas e correntes são implementados o espectro de Pierson-Moskowitz e o de JONSWAP. As cargas hidrodinâmicas são avaliadas pela equação de Morison. Estas cargas são integradas ao longo dos elementos estruturais e transformadas em cargas nodais equivalentes, de acordo com o proposto por Souza. A análise é realizada no domínio do tempo com algoritmo de Newmark. Este software, por ser específico para este tipo de torre, possui facilidades na introdução de dados e na modelagem da estrutura. Com estas estratégias o modelo apresentou bons resultados para a avaliação de cargas, cálculo de freqüências naturais, resposta de deslocamentos, esforços e reações.

The aim of the present communication is to present an analysis of the gravity load influence on the hysteretic behaviour of a beam-column connection. For this purpose, in the experimental campaign a new procedure for RC cyclic tests is presented in order to reproduce closer demands on the beam critical zone than the traditional procedures. The Experimental campaign included cyclic tests of the specimens according with the ECCS recommendation and an innovate procedure. The test results are presented, compared and analysed. A numerical simulation of the tests is presented where the model for the hysteretic response of the beam was calibrated with the experimental results. Finally, the behaviour of a portal frame system under cyclic displacements up to a drift of 3.5% was analysed, assuming that the non-linearity is concentrated on the plastic hinges, considering different levels of gravity load. Thus it is intended to assess the influence of the gravity load on the behaviour of a structure subjected to cyclic loads.

The recent development of inorganic based composites as low-cost materials in reinforced concrete structural strengthening and precast thin-walled components, requires the creation of models that predict the mechanical behaviour of these materials. Textile Reinforced Mortar (TRM) shows complex stress–strain behaviour in tension derived from the heterogeneity of its constituent materials. This complexity is mainly caused by the formation of several cracks in the inorganic matrix. The multiple cracking leads to a decrease in structural stiffness. Due to the severe conditions of the serviceability limit state in structural elements, the prediction of the stress–strain curve is essential for design and calculation purposes. After checking other models, an empirical nonlinear approach, which is based on the crack control expression included in the Eurocode 2, is proposed in this paper. Following this scope, this paper presents an experimental campaign focused on 31 TRM specimens reinforced with four different reinforcing ratios. The results are analysed and satisfactorily contrasted with the presented non-linear approach.

Earthquakes, soil settlements, traffic vibrations, and air pollution are some of the actions that can affect historic old buildings. Besides these, the lack of continuous maintenance puts a large part of this heritage in risk due to structural problems that reduce their own safety and that of their users. The preservation and risk mitigation of built cultural heritage require the use of reliable tools in order to assess its state of conservation and to identify and prevent potential vulnerabilities. Having this in mind, it is not possible to carry out destructive tests in most historic old buildings, so it is preferable to opt for nondestructive tests (NDT) or alternative methodologies that allow the physical and mechanical characterization of materials and structure. In this chapter, a general view of NDT methods used in historic buildings to obtain the geometrical information, the damage mapping, the mechanical and physical characterization, and the petrographic analysis of stones is presented. An alternative methodology to physically and mechanically characterize the stone of historic buildings using NDT tests is also proposed. The chapter ends with a case study carried out in the St. Leonard’s Church, a Portuguese monument built in Atouguia da Baleia village in the 13th century, where the alternative methodology here presented was applied. The final results of this study show that the methodology proposed allows the obtention of stress-strain curves in a completely nondestructive way, based on the water absorption coefficient at low pressure.

The wind energy production is a growing industry and the energy produced is renewable and environmentally cleaner than most of the energy production systems. The supports of the wind energy generators may be built with precast concrete elements. The precast solutions for these structures are competitive in comparison to other structural systems. The evolution of the technology for wind energy production shows a clear need for larger wind turbines and longer blades and, consequently, taller towers. The experience also shows that precast concrete solutions increase their competitiveness as the tower height increases. Offshore wind farms have some advantages in relation to onshore ones, which explains recent investments in this area. Also in this case, the durability of concrete in the sea when compared to steel, gives advantages to precast concrete in relation to other structural solutions. This paper shows the evolution of the supports of the wind energy generators and the advantages of the use of precast concrete towers.

n/a

Sandstone building stones are important in the building elements of Portuguese monuments, particularly in the western and southern regions. Alveolization due to salt crystallization was the most important degradation pattern found in the old sandstone façades of St. Leonardo’s Church, a Portuguese monument built in Atouguia da Baleia village in the Middle Age. Its sandstone façades have a widespread distribution of deep and large alveolization patterns mainly on portals and vaults that appeared as a result of the past and present vicinity of seashore. In this paper a summary of conservation interventions carried out in the past century in St. Leonardo’s Church is presented, as well as a summary of the studies carried out in the last decade. Then the degradation patterns on the sandstone walls of St. Leonard’s Church are shown and finally the evolution of the alveolization occurred on the sandstone walls over the last sixty to seventy years is analysed. Visual inspection of sandstone walls is compared with a survey performed by laser scanning, which seems to be a powerful technology to carry out 3D geometric modelling of the building elements of stone monuments and also the 3D mapping of stone degradation patterns.

The present study is part of an extensive research project, where the main objective is to evaluate a strengthening solution for reinforced concrete structures using a small thickness jacketing in the compression side of the RC element with unidirectional fiber reinforced grout - UFRG.
For this purpose a high performance cementitious grout reinforced with continuous and unidirectional non woven fibermat has been developed. It was expected that the use of these type of fibers allowed an optimization of its percentage and orientation. It was expected that the use of these type of fibers allowed an optimization of its percentage and orientation. Besides, for continuous fibers (with an aspect ratio, defined as the length-to-diameter ratio, l/d=∞), the composite should attain higher tensile strength since the fiber embedment length is enough to prevent fiber pullout.
The experimental campaign included a set of preliminary tests that allowed the design of the fiber reinforced grout, sustained with rheological parameters [7] and mechanical characterization tests of the materials.
Finally, an experimental campaign was carried out in order to proceed to the mechanical characterization of the unidirectional fiber reinforced grout. Compressive tests were conducted in small thickness tubular specimens that enable the determination of the compressive strength and the static modulus of elasticity of the material. The tensile strength of the material was obtained using splitting tests of cubic specimens (according the standard DIN 1048-5). The experimental results are presented and analyzed.

A reabilitação de um edifício tem muitas vezes de ser analisada e efetuada tendo em conta os edifícios vizinhos e a envolvente. No caso particular da reabilitação de um edifício, à partida devem considerar-se, de forma integrada, todos os requisitos que não são cumpridos face aos padrões atuais. Com base nessa análise, e tendo em conta muitas vezes condicionantes vários, que vão desde estéticos, técnicos, culturais a económicos, e que dependem em larga medida das tipologias construtivas, a intervenção tem de ser cuidadosamente concebida, preparada e executada. Apresentam-se sinteticamente as tipologias construtivas mais correntes, o contexto legislativo português da construção e específico da reabilitação. Efetua-se uma análise à legislação vigente, detalhando com maior detalhe o Regime Especial da Reabilitação Urbana, que possibilita dispensas de cumprimentos regulamentares mas apenas relativos a aspetos construtivos. Por esse motivo apresenta-se também uma síntese de aspetos relativos à segurança estrutural na reabilitação de edifícios com tipologias correntes. Pretende-se, através desta síntese, contribuir para uma visão mais integrada da reabilitação.