Rodrigo Martins

This paper aims to discuss the effect of order and disorder on the electrical performances of covalent silicon semiconductors and ZnO based ionic oxide semiconductors used as active channel layers in thin film transistors. The effect of disorder on covalent semiconductors directly affects their electrical transport properties due to the asymmetric behaviour of sp states, while in ionic oxide semiconductors it is found that this effect is small due to the fact that angular disorder has no effect on the spherical symmetry of s states. To this we must add that the mobility of carriers in both systems is quite different, being also affected by electron-phonon interactions (weak in silicon and strong in ionic oxides leading to formation of polarons). Besides, the impurity doping effect and the presence of vacancies in disordered silicon and in ionic oxides behave differently, which will influence the thin film properties and so, the performances of the devices produced. © 2007 Springer-Verlag.

This paper describes, for the first time, a method of producing polymorphous silicon (pm-Si:H) films by plasma-enhanced (PE) CVD, using an excitation frequency of 27.12 MHz. The aim is to produce, at high growth rates, nanostructured films that are more stable than the conventional amorphous or polymorphous silicon films grown by PECVD at 13.56 MHz. The processing data show that, at 27.12 MHz, the pm-Si:H films are produced close to the transition region from amorphous to microcrystalline silicon films, at a growth rate of about 0.3 nm s-1, using pressures above 160 Pa. Apart from that, the analysis of the exodiffusion, spectroscopic ellipsometry (SE), and micro Raman data reveal that these films are more dense and compact than the polymorphous films grown at 13.56 MHz.

The aim of this paper was to present results of the role of the d.c. grid bias on the silane plasma impedance and its I-V characteristics to grow undoped amorphous silicon (a-Si:H) films by plasma enhanced chemical vapour deposition (PECVD) in conditions where some nanoparticles can be formed in the growth region of the deposition process, under proper ion bombardment. The results achieved show that the performances of the films produced are dependent on the self bias voltage that can present photosensitivities of approximately 107 (two orders of magnitude larger than the one exhibited by films grown under conventional conditions) with density of states determined by the constant photocurrent method below 4×1015 cm-3. Apart from that, the films grown are less affected by light soaking than the conventional films.

The aim of this work is to present a model to interpret the static and the dynamic detection and resolution limits of 1D thin film position sensitive detectors based on p-i-n a-Si:H devices. The model can determine the device characteristics that influence the spatial limits and the response time of the device.

This paper presents results of the role of the oxygen partial pressure (pO2) used on the properties exhibited by doped μc silicon oxycarbide films produced by a Two Consecutive Decomposition and Deposition Chamber (TCDDC) system [1], where a spatial separation between the plasma and the growth regions is achieved. The films produced are highly conductive and transparent with suitable properties for optoelectronic applications.

We report the architecture and the performances of a memory based on a single field-effect transistor built on paper able to write-erase and read. The device is composed of natural multilayer cellulose fibers that simultaneously act as structural support and gate dielectric; active and passive multicomponent amorphous oxides that work as the channel and gate electrode layers, respectively, complemented by the use of patterned metal layers as source/drain electrodes. The devices exhibit a large counterclockwise hysteresis associated with the memory effect, with a turn-on voltage shift between 1 and -14.5 V, on/off ratio and saturation mobilities of about 104 and 40 cm 2 V-1 s-1, respectively, and estimated charge retention times above 14 000 h. © 2008 American Institute of Physics.

This paper presents data concerning the composition structure and optical characteristics of polymorphous silicon films produced by plasma enhanced chemical vapour deposition at 27.12 MHz and determined respectively by infrared spectrometry, micro Raman, exodiffusion and spectroscopic ellipsometry measurements. When compared to the pm-Si:H films produced at 13.56 MHz, the films produced at 27.12 MHz present hydrogen contents in the range of 21 at%, the sharp peak ascribed to the exodifusion measurements is shifted towards high temperatures and the imaginary part of the dielectric function 〈ε2〉 is larger and shifted to high energies. Apart from that the peaks of the infrared spectra ascribed to the stretching modes shift towards high wave numbers and the half width of the micro Raman peaks shrinks, meaning that the films produced at 27.12 MHz are more compact and dense.

This paper presents the process conditions that lead to the production of nanostructured silicon films grown by plasma enhanced chemical vapour deposition close to the so-called gamma regime (powder formation), highly dense and with low density of bulk states. Thus, the powder management is one important issue to be addressed in this paper. As a general rule we observed that high quality films (low density of states and high μτ products) are obtained when films are grown under low ion bombardment at high hydrogen dilution and deposition pressure conditions, to allow the proper surface passivation and surface activation.

In this work, we present a model to interpret the steady-state and the dynamic detection limits of 1-D Thin Film Position Sensitive Detectors (1-D TFPSD) based on p-i-n a-Si:H devices. From this, an equivalent electric circuit is derived and the predicted values are compared with the experimental results obtained in 1-D TFPSD devices, with different sizes. The model is also able to determine the device characteristics that influence the spatial limits and the response time of the device. © 1996 IEEE.

A linear array thin film position sensitive detector (LTFPSD) based on hydrogenated amorphous silicon (a-Si:H) is proposed for the first time, taking advantage of the optical properties presented by a-Si:H devices we have developed a LTFPSD with 128 integrated elements able to be used in 3-D inspections/measurements. Each element consists on a one-dimensional LTFPSD, based on a p.i.n. diode produced in a conventional PECVD system, where the doped layers are coated with thin resistive layers to establish the required device equipotentials. By proper incorporation of the LTFPSD into an optical inspection camera it is possible to acquire information about an object/surface, through the optical cross-section method. The main advantages of this system, when compared with the conventional CCDs, are the low complexity of hardware and software used and that the information can be continuously processed (analogue detection).

This paper reports the performance of small area solar cells, 128 linear integrated position sensitive detector arrays and thin film transistors based on nanostructured silicon thin films produced by plasma-enhanced chemical vapour deposition technique, close to the onset of dusty plasma conditions, within the transition region from amorphous to microcrystalline. The small area solar cells, produced in a modified single chamber reactor, exhibited very good electrical characteristics with a conversion efficiency exceeding 9%. The 128 integrated position sensitive detector arrays, based on a similar pin structure, allow real-time 3D object imaging with a resolution higher than 90 l p/mm. The thin film transistors produced exhibited field effect mobility of 2.47 cm 2/V/s, threshold voltage of 2 V, on/off ratio larger than 10 7 and sub-threshold slopes of 0.32 V/decade, which are amongst the best results reported for this type of device. © 2009 Taylor & Francis.

This paper studies the dc and ac impedance behaviour of undoped ZnO thin films produced by spray pyrolysis and rf magnetron sputtering under UV light illumination, at room temperature, emphasising the role that the crystallite size, structure, surface morphology and the state of surface have on the electrical responsivities obtained. The results achieved show that the sputtered films with crystal sizes of about 4 nm exhibit dc electrical UV responsivities of 108. On the other hand, the spray pyrolysis films exhibit the lowest dc responsivities, due the high crystal sizes and state of surface contamination, to which very good capacitance responses were obtained, mainly due to the degree of porosity exhibit by these films when produced at low temperatures. Based on that, a two-phase electrical model is proposed to explain the set of behaviours observed. © 2005 Elsevier B.V. All rights reserved.

This paper deals with the growth process of nanostructured silicon films produced by chemical vapour deposition technique, at or close to the γ-regime where powders are formed. There, besides the set of chemical reactions undertaken by the species decomposed on the growth surface, the importance of the physics of the plasma in managing the powders and on the final film performances will be shown. To identify the plasma region where Si nanoaggregates are formed, we propose the use of a new parameter that translates the energy coupling of the rf power to the species of the gas flow, per pressure range of the process. By doing so we could establish an excellent correlation between this ratio and the plasma parameters such as peak to peak rf voltage and plasma impedance, or with the films defect density and their transport properties. Apart from that, we also show that high compact Si nanoclusters could be grown under moderate ion bombardment. Finally, to allow the growth at high rates of controlled silicon nanostructures, a three cycling process based on hot wire chemical vapour deposition and plasma assisting the hot wire technique will be discussed. © 2002 Elsevier Science Ltd. All rights reserved.

The aim of this paper is to present data on the dependence of the electro-optical characteristics and structure of n-type microcrystalline silicon films on the r.f. power used during the deposition of films produced by the plasma-enhanced chemical vapour deposition technique. The interest of these films arise from the fact that they combine some electro-optical advantages of amorphous (wide optical gap) and crystalline materials (electronic behaviour), highly interesting in the production of a wide variety of optoelectronic devices such as solar cells and thin film transistors. In this paper, microcrystalline n-type films presenting simultaneously optical gaps of about 2.3 eV, dark conductivity of 6.5 S cm-1 and Hall mobility of about 0.86 cm2 V-1 s-1 will be reported, the highest combined values for n-type microcrystalline silicon films, as far as we know. © 1997 Elsevier Science S.A.

This work presents experimental data concerning the role of the oxygen partial pressure used during the preparation process, on the structure, composition and optoelectronic properties of wide band gap doped microcrystalline silicon oxycarbide films produced by a TCDDC system [1].

Reported herein is a nonvolatile n-type floating gate memory paper field-effect transistor, emphasizing the role of the paper structure and properties on the device performance recorded such as in the high capacitance per unit area at low frequencies (>2.5 μFcm-2) and so on the set of high charge retention times achieved (>16000 hours). The device was built via the hybrid integration of natural cellulose fibers, which act simultaneously as substrate and gate dielectric, using amorphous indium zinc and gallium indium zinc oxides respectively for the gate electrode and channel layer. This was complemented by the use of continuous patterned metal layers as source/drain electrodes. © 2010 Copyright SPIE - The International Society for Optical Engineering.

This work reports on the performances of undoped and doped amorphous/nanocrystalline silicon films grown by hot wire plasma assisted technique. The structure (including the presence of several nanoparticles with sizes ranging from 5 nm to 50 nm), composition (oxygen and hydrogen content) and transport properties of the films are highly dependent on the temperature of the filament and on the hydrogen dilution. The undoped films grown under low r.f. power (≈4mWcm-2) and filament temperatures around 1850 K present dark conductivities below 10-10 Scm-1, optical gaps of about 1.6 eV and photosensitivities above 105, (under AM 1.5 light intensities), with almost no traces of oxygen content. For the n- and the p-doped silicon films also fabricated under the same conditions the conductivities obtained are of about 10-2Scm-1 and 10-5Scm-1, respectively. © 1998 Elsevier Science Ltd. All rights reserved.

The aim of this work is to present an analytical model able to interpret the experimental data of the dependence of film's uniformity on the discharge pressure, gas flow and temperature used during the production of thin films by the plasma enhancement chemical vapour deposition technique, under optimised electrode's geometry and electric field distribution. To do so, the gas flow is considered to be quasi-incompressible and inviscous leading to the establishment of the electro-fluid-mechanics equations able to interpret the film's uniformity over the substrate area, when the discharge process takes place in the low power regime.

A linear array thin film position sensitive detector (LTFPSD) based on hydrogenated amorphous silicon (a-Si:H) is proposed for the first time. Taking advantage of the optical properties presented by a-Si:H devices, we have developed a LTFPSD with 128 integrated elements able to be used in 3D inspections/measurements. Each element consists of a one-dimensional LTFPSD, based on a p-i-n diode produced in a conventional PECVD system, where the doped layers are coated with thin resistive layers to establish the required device equipotentials. By proper incorporation of the LTFPSD into an optical inspection camera it will be possible to acquire information about an object/surface, through the optical cross-section method. The main advantages of this system, when compared with the conventional CCDs, are the low complexity of hardware and software used and that the information can be continuously processed (analog detection). © 1995 American Institute of Physics.

The current transport in metal-amorphous semiconductor barriers is examined by solving the proper Poisson's equation and transport equations within the semiconductor's space charge region taking into account the role of trap shallow states distribution function. The effect of metal is also included through appropriate boundary conditions of the above solutions. Generalized transport equations will be derived either when thermionic drift-diffusion emission process dominates or when the conduction mechanism is mainly due to drift-diffusion emission. Both situations will be analysed with or without neglecting carriers losses during their collision free path, from which a tractable expression for the current-voltage characteristic will be determined.

A complementary metal oxide semiconductor (CMOS) device is described. The device is based on n-(In-Ga-Zn-O) and p-type (SnO x) active oxide semiconductors and uses a transparent conductive oxide (In-Zn-O) as gate electrode that sits on a flexible, recyclable paper substrate that is simultaneously the substrate and the dielectric. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The electrosynthesis of polypyrrole (PPy) has been achieved on aluminium in aqueous medium of malic acid by means of cyclic voltammetry, potentiostatic and galvanostatic techniques. Scanning electron microscopy (SEM) and X-ray microanalysis by dispersion energy spectroscopy (EDS) applying on surfaces show that the PPy coating is developed from the metal surface through the cracks of the initial Al2O3 layer. Moreover, the results reveal that the homogeneity of the film achieved increases with the time of electropolymerization. A mechanism involving the participation of the supporting electrolyte and the pyrrole (Py) in distinct active sites was proposed based on the linear sweep voltammetry. It is observed for all the applied electrochemical techniques that the pyrrole concentration has to be higher than 0.1 M to allow the polypyrrole electrodeposition in acid medium. Scanning electron microscopy, secondary electrons (SE) and backscattering electrons (BE), shows that the PPy coating obtained in galvanostatic and potentiostatic modes starts with small islands at weak applied potentials or current densities. The corrosion results in 3% NaCl medium show that the PPy coating decreases the corrosion behaviour of the aluminium. The bilayer Al2O3/PPy shows a capacitor with future applications. © 2006 Elsevier B.V. All rights reserved.

Where a-Si:H pin devices are concerned, one of the main obstacles regarding improved performance is device stability, usually attributed to adverse behaviour at various interfaces within the device. Several attempts have been made to overcome this problem, such as the use of blocking layers at the interfaces. Although these have led to some improvements in device performance, most of the problems associated with device stability remain. This is mainly due to the defects at the interfaces, since the blocking layers (silicon alloys with carbon, nitrogen or oxygen) usually have a high density of bulk states, in comparison to intrinsic a-Si:H films. In this paper, we present a method that seems to be capable of improving device stability. It consists of performing a controlled removal of oxide interlayers at the interfaces, by an appropriate etching process. This enables the production of highly smoothed interfaces, and reduces possible cross-contamination of the i-layer from the adjacent doped layers. This amounts to a new design of typical pin devices, in which thin absorber layers are placed at the p/i and i/n interfaces. Their purpose is to trap most of the impurity atoms diffused from the doped layers, after which they are removed by appropriate etching. The fabrication of the absorbers (sacrificial layers), the nature of the etching and the tailoring of the defect profile at the interfaces will be discussed, including the performance exhibited by the resulting devices. © 2002 Elsevier Science B.V. All rights reserved.

This paper deals with the study of the role of gas temperature and of the ratio of r.f. power to gas flow on the particle's formation in amorphous silicon films grown by the plasma enhanced chemical vapour deposition technique, by monitoring the plasma impedance behaviour under different process conditions. The results achieved show the existence of two main boundary regions separating the so-called α-regime (no powder formed) from the γ-regime (powder formed). Those regions are reached either by heating the gas, changing the gas pressure or using high power to gas flow ratios, corresponding to the establishment of a balance between the plasma resistance and the plasma reactance. In the β-region the probability to incorporate nanoparticles in the films is low and the films exhibit photosensitivity's of about 105 with density of states determined by the constant photocurrent method below 6×1015 cm-3 with Urbach energies below 50 meV. In the θ-region small nanoparticles can be incorporated leading to films with density of states below 3×1015 cm-3, with Urbach energies above 50 meV and photosensitivity's above 106, about two orders of magnitude larger than that of conventional amorphous silicon grown in the α-regime.