Carlos Chastre

n/a

A produção de betão com substituição de agregados naturais por agregados reciclados minimiza os impactes da indústria da construção. Contudo, o recurso a este tipo de agregado é limitado devido a dúvidas dos diferentes agentes da indústria da construção e à ausência de regulamentação específica para o projecto de betão com agregados reciclados. A percepção de betões com agregados reciclados como um material heterogéneo com comportamento imprevisível é o principal entrave, quer para a aceitação da indústria, quer para o desenvolvimento de regulamentação. Diferentes aspectos relacionados com o efeitos da variabilidade das propriedades de betão com agregados reciclados na regulamentação de estruturas são abordados conceptualmente: a heterogeneidade dos agregados reciclados, o efeito desta heterogeneidade nas propriedades mecânicas de betão e os efeitos da variabilidade das propriedades de betão na sua fiabilidade estrutural. Os primeiros resultados de uma campanha experimental desenvolvida especificamente para abordar o efeito de agregados grossos reciclados na fiabilidade são apresentados e as suas implicações no projecto de estruturas discutidas. São apresentadas sugestões de desenvolvimentos futuros que visam a calibração de coeficientes parciais de segurança que possibilitem o projecto de estruturas de betão armado dimensionadas segundo o formato do Eurocódigo 2 e mantendo os mesmos níveis de segurança de betão convencional.

Reinforced concrete (RC) beams externally strengthened with glass fiber-reinforced polymer (GFRP) strips bonded to the soffit may see their load-carrying capacity reduced due to environmental conditions—especially due to the deterioration of bond between the adhesively bonded laminates and concrete, causing premature failure.
More research has been published on the detachment of the laminate progressing from the anchorage zone than on failure induced by the formation of flexural or shear-flexural cracks in the midspan followed by fiber-reinforced polymer (FRP) separation and failure designated as intermediate crack (IC) debonding. An experimental program to study degradation of the GFRP laminate beam specimens after accelerated temperature cycles, namely: 1) freezing-and-thawing type; and 2) cycles of the same amplitude (40°C [104°F]) and an upper limit approximately 70% of the glass vitreous transition temperature of the resin, Tg, is described.
Effects on the bond stress and ultimate capacity are reported. Substantial differences between shear and bending-induced failure and a decrease of bond stresses and engagement of the laminates on the structural response are analyzed.

Despite the fact that FRP composites are a reliable structural material with reasonable durability performance, the environment to which the strengthened structure is exposed can make the strengthening system vulnerable. In this study, the effectiveness of Externally Bonded Reinforcement (EBR) systems when external compressive stresses are applied to glass (G) FRP-to-concrete interfaces in several aggressive environments is analysed. The compressive stress imposed on the GFRP-to-concrete interface intends to simulate, for instance, the effect produced by a mechanical anchorage system applied to the EBR system. The design and the region to set those mechanical anchorage systems are not yet well understood and are mostly applied without really knowing how they will behave. This work shows an exhaustive experimental programme based on several double shear tests subjected to salt fog cycles, dry/wet cycles and two distinct temperature cycles: from -10ºC to +30ºC and +7.5ºC to +47.5ºC. The Mohr-Coulomb failure criterion was found to provide a good representation of the performance of the GFRP-to-concrete interface, and changes of cohesion and internal friction angle of those interfaces during the hours of exposure to the aggressive environments are reported.

Measurements in civil engineering load tests usually require considerable time and complex procedures. Therefore, measurements are usually constrained by the number of sensors resulting in a restricted monitored area. Image processing analysis is an alternative way that enables the measurement of the complete area of interest with a simple and effective setup. In this article photo sequences taken during load displacement tests were captured by a digital camera and processed with image correlation algorithms. Three different image processing algorithms were used with real images taken from tests using specimens of PVC and Plexiglas. The data obtained from the image processing algorithms were also compared with the data from physical sensors. A complete displacement and strain map were obtained. Results show that the accuracy of the measurements obtained by photogrammetry is equivalent to that from the physical sensors but with much less equipment and fewer setup requirements.