Rodrigo Martins

The aim of this work is to interpret the role of the lateral leakage current on the a-Si:H solar cell performances (J-V characteristics, responsivity and the apparent device degradation behaviour), under low illumination conditions.

In this work we present results of studies performed on Schottky and metal-insulator-semiconductor (MIS) position sensitive detectors (PSD) structures: substrate (glass)/ Cr (300 nm) / a-Si:H [n] (37 nm) / a-Si:H [i] (600 nm) / SiO2 (1.5 nm - for the MIS) / Au (7 nm). The effect of the interfacial oxide layer between Au and a-Si:H, for the MIS structures, was studied and compared with the Schottky, in order to determine how beneficial it could be for device performances and time degradation. For doing so, the Au thickness of 70Å was deposited by thermal evaporation on an oxide free (Schottky) and oxidized (≈20Å) (MIS) a-Si:H surfaces. These structures were characterized by SIMS, RBS, SEM and AFM in order to correlate the obtained diffusion profile of Au at the interface and the topography with the presence of the oxide at the interface. The results show that the Au inter-diffuses very easily in the oxide free a-Si:H surface, even at room temperature, degrading the devices performance. On the other hand, the MIS structures, with their interfacial oxide present no structural changes after annealing and the PSD produced are stable. We believe that this effect is associated with the barrier effect of the interfacial oxide that prevents the Au diffusion. The optimized 1D MIS sensors are stable and exhibit a linearity error as low as 0.8 % and sensitivities of 33 mV/cm for a 5 mW spot beam intensity at a wavelength of 532 nm, while the Schottky sensors showed a time degradation of their characteristics. © 2006 Materials Research Society.

Silicon oxycarbide microcrystallinc layers, n- and p-doped, highly conductive and highly transparent have been produced using a Two Consecutive Decomposition and Deposition Chamber (TCDDC) system. The films exhibit suitable properties for optoelectronic applications where wide band gap materials with required conductivity and stability are needed. In this paper we present the role of partial oxygen pressure (po2) in controlling the composition, structure and transport properties (conductivity. δd and optical gap, Eop) of silicon oxycarbide microcrystalline layers. © 1994 Materials Research Society.

The aim of this work is to provide the basis for the interpretation, under steady state, of the lateral photoeffect in p-i-n a-Si:H 1D Thin Film Position Sensitive Detectors (1D TFPSD) through an analytical model. The experimental data recorded in 1D TFPSD devices with different performances are compared with the predicted curves and the obtained correlation's discussed.

The combination of high transparency and good thermoelectric properties of SnO2 can open new field of applications for the thin film thermoelectric materials. Here we report on SnO2 thin films with transmittance above 90%, resistivity bellow 10-3Ωm and a Power Factor around 10-4 W/m.K2, for a Seebeck of -255μV/K, at room temperature. The effect of film thickness and post-deposition annealing on the thermoelectric properties were analysed. The performances of a single layer thermoelectric device are also presented. © 2015 .

Thin films of molybdenum doped indium oxide (IMO) were rf sputtered onto glass substrates at room temperature. The films were studied as a function of oxygen volume percentage (OVP) ranging 1.4 - 10.0% in the sputtering chamber. The thickness of the films found varying between 180 and 260 nm. The X-ray diffraction pattern showed the films are polycrystalline with the peaks corresponding to (222) and (400) planes and one among them showing as a preferential orientation. It is observed that the preferred orientation changes from (222) plane to (400) as the OVP increases from 1.4 to 10.0%. The transmittance spectra were found to be in the range of 77 to 89%. The optical band gap calculated from the absorption coefficient of transmittance spectra was around 3.9 eV. The negative sign of Hall coefficient confirmed the films were n-type conducting. The bulk resistivity increased from 2.26×10 -3 to 4.08×-1 Ωcm for the increase in OVP from 1.4 to 4.1%, and thereafter increased dramatically so as the Hall coefficients were not detectable. From the AFM morphologies it is evaluated that the RMS roughness of the films ranges from 0.9 to 3.2 nm. © 2006 Materials Research Society.

The introduction into a traditional p.i.n. structure of two defective buffer layers near the p/i and i/n interfaces can improve the device stability and efficiency through an enhancement of the electric field profile at the interfaces and a reduction of the available recombination bulk centers. The defectous layer (`i-layer'), grown at a higher power density, present a high density of the defects and acts as `gettering centers' able to tailor light induced defects under degradation conditions. If the i-layer density of states remains below 1016 eV-1 cm-3 and assuming a Gaussian distribution of defect states, the gettering center distribution will not affect significantly the carrier population but only its spatial distribution. We report here about a device numerical simulation that allows us to analyze the influence of the `i- layer' position, thickness and density of states on the a-Si:H solar cells performances. Results of some systematic simulation rom the ASCA program (Amorphous Solar Cell Analysis), and for different configurations will be presented.

This work reports the structure and electro-optical characteristics of different metal oxide films obtained by spray pyrolysis on heated glass substrates, aiming their application in optoelectronic devices. The results show that this technique leads to thin films with properties ranging from dielectric to degenerate semiconductors, offering the following advantages: simplicity, low cost, high productivity and the possibility of covering large areas, highly important for large area device applications.

High-quality SrBi2Nb2O9 (SBN) single crystals were grown from a melt using a high-temperature self-flux solution method and Bi2O3 added with B2O3 as a flux. A suitable thermal profile involving slow cooling rates allowed growing large and translucent SBN crystals exhibiting platelet morphology with typical size ∼5 × 5 mm2 and thickness approximately 400 μm. X-ray diffraction revealed a dominant (001)-orientation of the major face of the platelet crystals and edges oriented parallel to the [110] directions. The dielectric properties were evaluated along the ab-plane and in the c-axis direction. The ferro-paraelectric phase transition was observed at TC = 440°C with Curie-Weiss relationship above TC. The anisotropy of dielectric permittivity, i.e., the ratio between permittivity in the ab-plane and along c-axis was about 10 at TC-The obtained results are used to discuss the observed correlations between anisotropy, crystalline orientation, and electrical properties.

Diffraction and other structural measurements on n-type SiC thin films prepared in a TCDDC (two consecutive decomposition and deposition chamber) system indicate the presence of Si microcrystals (without evidence for SiC crystallites). Weakly absorbing, highly conductive layers (σ ≥ 10-1 (Ω-cm)-1) contain up to 20 at.% C and 25 at.% O. The optoelectronic properties of these films can be explained in terms of a sufficient volume fraction (above the percolation threshold) of Si microcrystals surrounded by an a-Si:C:O:H matrix.

This work presents experimental data concerning the role of the oxygen partial pressure used during the preparation process, on the structure, composition and optoelectronic properties of wide band gap doped microcrystalline silicon oxycarbide films produced by a TCDDC system [1].

This work deals with the study of the role of the buffer layers thickness on the TCO/p-a-SiC:H/buffer1/buffer2/i(nc-Si/a-Si:H)/n-a- Si:H/Al solar cell I-V and impedance performances. The aim was to improve the p/i interface region, which has a large influence on the solar cell characteristics and stability. In order to match the difference between the p and i layers optical gaps, the buffer layers were deposited using, for each layer, different methane to silane mixtures, aiming to obtain a gradual match of the corresponding optical gaps. The intrinsic layer was deposited at high hydrogen dilution rates at 27.12 MHz in conditions that allowed the incorporation of nanoparticles/nanoclusters. Solar cells with fill factor of 0.63; open circuit voltage of 0.93 Volts; short circuit current density of 16.13 mA/cm2 and an efficiency of 9.4% were produced with buffer layers around 1.3 nm thick. When comparing these solar cells with conventional amorphous silicon solar cells we notice that the quantum efficiency from ultraviolet to green regions is improved up to 13%, in average. Concerning solar cell capacitance, the data show that the best solar cells exhibit the highest capacitance, meaning that the films are compact and dense, in-line with the other electrical characteristics obtained. ©2005 IEEE.

Tin doped indium oxide (ITO) films were deposited on glass substrates by rf reactive magnetron sputtering using a metallic alloy target (In-Sn, 90-10). The post-deposition annealing has been done for ITO films in air and the effect of annealing temperature on the electrical, optical and structural properties of ITO films was studied. It has been found that the increase of the annealing temperature will improve the film electrical properties. The resistivity of as-deposited film is about 1.3×10-1 Ω* cm and decreases down to 6.9×10-3 Ω* cm as the annealing temperature is increased up to 500°C. In addition, the annealing will also increase the film surface roughness which can improve the efficiency of amorphous silicon solar cells by increasing the amount of light trapping.

Sensitivity tests to reductive gases such as methane, hydrogen and ethane were performed on zinc oxide (ZnO) thin films. The highest value of sensitivity was obtained for the film with a high electrical resistivity and a low thickness. The variation of the operating temperature of the film leads to a significant change in the sensitivity of the sensor with an ideal operating temperature dependence of the gas used. The sensitivity of the ZnO thin films changes linear with the increase of the gas concentration. However these films seem to be more appropriated for the detection of hydrogen following by methane and than for ethane since the value of sensitivity obtained are higher and its variation with the gas concentration more pronounced.

Highly textured transparent conducting ZnO:Al thin films have been prepared by r.f. magnetron sputtering. The films were deposited on polyester (Mylar type D, 100 μm thickness) and glass substrates at room temperature. Surface stylus profiling, X-ray diffraction, scanning electron microscopy, transmission electron microscope and Hall effect measurements as a function of temperature, using the van der Pauw technique have characterized the films. The samples are polycrystalline with a hexagonal wurtzite structure and a strong crystallographic c-axis orientation (002) perpendicular to the substrate surface (columnar structure). The ZnO:Al thin films with a resistivity as low as 3.6×10-2 Ωcm have been obtained, as deposited. © 2001 Materials Research Society.

Highly textured transparent conducting ZnO:Al thin films have been prepared by r.f. magnetron sputtering. The films were deposited on polyester (Mylar type D, 100 μm thickness) and glass substrates at room temperature. Surface stylus profiling, X-ray diffraction, scanning electron microscopy, transmission electron microscope and Hall effect measurements as a function of temperature have been used to characterize the produced films. The samples are polycrystalline with a hexagonal wurtzke structure and a strong crystallographic c-axis orientation (002) perpendicular to the substrate surface (columnar structure). The ZnO:Al thin films with a resistivity as low 3.6×10-2 Ωcm have been obtained, as deposited.

This paper analyzes transparent two-TFT current mirrors using a-GIZO TFTs with different mirroring ratios. In order to achieve a high mirroring ratio, the output TFT in the circuit employed a fingered structure layout to minimize area and overlap capacitance. The analysis of the current mirrors is performed in three phases. In the first, a radial basis function based (RBF) model is developed using measured data from fabricated TFTs on the same chip. Then, in the second phase, the RBF model is implemented in Verilog-A that is used to simulate two-TFT current mirrors with different mirroring ratios. The simulations are carried out using Cadence spectre simulator. In the third phase, simulation results are validated with the measured response from the fabricated circuits. © 2014 IEEE.

This paper presents results of the role of the oxygen partial pressure (pO2) used on the properties exhibited by doped μc silicon oxycarbide films produced by a Two Consecutive Decomposition and Deposition Chamber (TCDDC) system [1], where a spatial separation between the plasma and the growth regions is achieved. The films produced are highly conductive and transparent with suitable properties for optoelectronic applications.

In today's main crystalline silicon (c-Si) applications in MOS (metal-oxide-silicon), MIS (metal-insulator-semiconductor) or SIS (Semiconductor-Insulator-Semiconductor), the growing of the oxide layer plays the main role, dictating the device performances, in particular if it has to be grown by a low temperature process. Of fundamental importance is the SiO2 interface with the c-Si. A very low defect density interface is desirable so that the number of trapping states can be reduced and the devices performance optimised. A two step low temperature oxidation process is proposed. The process consists of growing first a layer of oxide by a wet process and then treating the grown oxide with an oxygen plasma. The oxygen ions from the plasma bombard the oxide causing compaction of the oxide and a decrease in the interface roughness and defect density. Infrared spectroscopy and spectroscopic ellipsometry measurements were performed on the samples to determine the oxide thickness, optical and structural properties. SIS structures were built and capacitance measurements were performed under dark and illuminated conditions from which were inferred the interface defect density and correlated with the oxide growth process.

This paper discusses the effect of order and disorder on the electrical and optical performance of ionic oxide semiconductors based on zinc oxide. These materials are used as active thin films in electronic devices such as pn heterojunction solar cells and thin-film transistors. Considering the expected conduction mechanism in ordered and disordered semiconductors the role of the spherical symmetry of the s electron conduction bands will be analyzed and compared to covalent semiconductors. The obtained results show p-type c-Si/a-IZO/poly-ZGO solar cells exhibiting efficiencies above 14% in device areas of about 2.34 cm2. Amorphous oxide TFTs based on the Ga-Zn-Sn-0 system demonstrate superior performance than the polycrystalline TFTs based on ZnO, translated by ION/IOFF ratio exceeding 107, turn-on voltage below 1-2 V and saturation mobility above 25 cm2/Vs. Apart from that, preliminary data on p-type oxide TFT based on the Zn-Cu-O system will also be presented. © 2009 SPIE.

Aluminium doped zinc oxide thin films (ZnO:Al) have been deposited on polyester (Mylar type D, 100 μm thickness) substrates at room temperature by r.f. magnetron sputtering. The structural, morphological, optical and electrical properties of the deposited films have been studied. The samples are polycrystalline with a hexagonal wurtzite structure and a strong crystallographic c-axis orientation (002) perpendicular to the substrate surface. The ZnO:Al thin films with 85% transmittance in the visible and infra-red region and a resistivity as low as 3.6×102 Ωcm have been obtained, as deposited. The obtained results are comparable to those ones obtained on glass substrates, opening a new field of low cost, light weight, small volume, flexible and unbreakable large area optoelectronic devices. © 2001 Materials Research Society.

In this paper we present results of intrinsic/non doped zinc oxide films deposited at room temperature by rf magnetron sputtering able to be used as a truly semiconductor on electronic devices like ozone gas sensors and ultra-violet detectors. The produced films are polycrystalline with a c-axis preferential orientation parallel to the substrate. The films' resistivity varies from 4.0×10-2 Ωcm to 1.0×10-9 Ωcm, depending on the deposition conditions used (rf power density and oxygen partial pressure), which turns not affecting the optical properties (in average a transmittance of around 85 % and an optical band gap of about 3.44 eV, independent of the deposition conditions used). When exposed to UV light the sensor response based on these films may exceed more than 5 orders of magnitude, recovering to the initial state in the presence of ozone. The sensitivity of the films is improved when the oxygen partial pressure increases and the rf power density used decreases, due to changes on the structural properties of the films. © 2006 Materials Research Society.

Engineering procedures governing the selection or development of printable nanostructured metal oxide nanoparticles for chromic, photovoltaic, photocatalytic, sensing, electrolyte-gated TFTs, and power storage applications are established in this chapter. The main focus is given on how to perform the material selection and formulation of printable dispersion in order to develop functional films for electrochemical applications. This chapter is divided into four main parts. Firstly, a brief introduction on electrochemically active nanocrystalline metal oxide films developed via printing techniques is given. This is followed by the description of the film morphology, structure, and required functionality. A theoretical approach to understand the impact of size and shape of nanoparticles on an ink formulation and electrochemical performance being the subject of the third section provides a greater control over the material selection. We attempt to describe these properties and show that for a given material, geometry and size of the nanoparticles have a major influence on the electrochemical reactivity and response time. This gives the ability to tune the performance of the film simply by varying the morphology of incorporated nanostructures. This section is completed by the recommendations on each major step of an ink formulation, together with imposed critical constraints concerning the fluid control. Finally, the performance of the ink-jetprinted dual-phase electrochromic films is discussed as a case study. By providing such a rather systematic survey, we aim to stress the importance of proper design strategy that would result in both improved physicochemical properties of nanoparticle-loaded inks and enhanced electrochemical performance of printed functional films. © Springer International Publishing Switzerland 2016.

Transparent electronics is emerging as one of the most promising technologies for the next generation of electronic products, away from the traditional silicon technology. It is essential for touch display panels, solar cells, LEDs and antistatic coatings. The book describes the concept of transparent electronics, passive and active oxide semiconductors, multicomponent dielectrics and their importance for a new era of novel electronic materials and products. This is followed by a short history of transistors, and how oxides have revolutionized this field. It concludes with a glance at low-cost, disposable and lightweight devices for the next generation of ergonomic and functional discrete devices. Chapters cover: Properties and applications of n-type oxide semiconductors P-type conductors and semiconductors, including copper oxide and tin monoxide Low-temperature processed dielectrics n and p-type thin film transistors (TFTs) - structure, physics and brief history Paper electronics - Paper transistors, paper memories and paper batteries Applications of oxide TFTs - transparent circuits, active matrices for displays and biosensors Written by a team of renowned world experts, Transparent Oxide Electronics: From Materials to Devices gives an overview of the world of transparent electronics, and showcases groundbreaking work on paper transistors. © 2012 John Wiley & Sons, Ltd.