Rodrigo Martins

Hydrogenated nanocrystalline silicon (nc-Si:H) n-layers have been used to prepare heterojunction solar cells on flat p-type crystalline silicon (c-Si) wafers. The nc-Si:H n-layers were deposited by radio-frequency (RF) plasma enhanced chemical vapor deposition (PECVD), and characterized using Raman spectroscopy, optical transmittance and activation energy of dark-conductivity. The nc-Si:H n-layers obtained comprise fine grained nanocrystallites embedded in amorphous matrix, which have a wider bandgap and a smaller activation energy. Heterojunction solar cells incorporated with the nc-Si n-layer were fabricated using configuration of Ag (100 nm)/lT0 (80 nm)/n-nc-Si:H (15 nm)/buffer a-Si:H/p-c-Si (300 μm)/Al (200 nm), where a very thin intrinsic a-Si:H buffer layer was used to passivate the p-c-Si surface, followed by a hydrogen plasma treatment prior to the deposition of the thin nanocrystalline layer. The results show that heterojunction solar cells subjected to these surface treatments exhibit a remarkable increase in the efficiency, up to 14.1% on an area of 2.43 cm2. © 2006 Elsevier B.V. All rights reserved.

PIN devices based on hydrogenated amorphous silicon (a-Si:H) became fundamental elements of many different types sensors, based on either the transverse or the lateral photovoltaic effect. In the past we have developed a transient technique, called the Flying Spot Technique (FST), based on the lateral photoeffect. FST allows, not only to infer the ambipolar diffusion length but also the effective lifetime of the photogenerated carriers once the light spot velocity and geometry of the structure were known. In this paper we propose to apply this technique backwards in order to detect the path and velocity of an object that is moving in a light source direction. The light reflected back from the object is analyzed through p.i.n. structure being the transient transverse photovoltage dependent on the object movement (position and velocity). Assuming known the transport properties of the material and the geometry of the device and using a triangulation method we show that it is possible to map the object movement. Details concerning material characterization, simulation and device geometry are presented.

In the past we have developed a transient technique, called the Flying Spot Technique (FST). FST allows, not only to infer the ambipolar diffusion length but also the effective lifetime of the photogenerated carriers once the light spot velocity and geometry of the structure were known. In this paper, we propose to apply this technique backwards in order to detect the path and velocity of an object that is moving in the direction of a light source. The light reflected back from the object is analyzed through a p.i.n structure being the transient transverse photovoltage dependent on the movement of the object (position and velocity). Assuming that the transport properties of the material and the geometry of the device are known and using a triangulation method we show that it is possible to map the movement of the object. Details concerning material characterization, simulation and device geometry are presented.

A double-chamber system was used to deposit large-area hydrogenated amorphous silicon films for photovoltaic applications. The electro-optical characterisation of films of area 400 cm2 deposited on glass substrates is described in this paper. The deposition rate of the films is dependent on the r.f. power delivered, the substrate bias and the partial pressure of the reactive gas. The film thickness was observed to have a uniformity of better than 0.5%. The best film quality was obtained for a deposition rate of about 1.5 Å s-1. The optical gap, activation energy, photosensitivity, density of gap states and hydrogen content were determined. © 1985.

In this work the electrical and structural properties of two high k materials as hafnium oxide (HfO2) and tantalum oxide (Ta2O5) produced at room temperature are exploited. Aiming low temperature processing two techniques were employed: r.f. sputtering and electron beam evaporation. The sputtered HfO2 films present a nanocrystalline structure when deposited at room temperature. The same does not happen for the evaporated films, which are essentially amorphous. The density and the electrical performance of both sputtered and evaporated films are improved after annealing them at 200 °C. On the other hand, the Ta2O5 samples deposited at room temperature are always amorphous, independently of the technique used. The density and electrical performance are not so sensitive to the annealing process. The set of data obtained show that these dielectrics processed at temperatures below 200 °C present promising properties aiming to produce devices at low temperature with improved interface properties and reduced leakage currents. © 2007 Elsevier B.V. All rights reserved.

This paper describes the development of a novel microfluidic platform for multifactorial analysis integrating four label-free detection methods: electrical impedance, refractometry, optical absorption and fluorescence. We present the rationale for the design and the details of the microfabrication of this multifactorial hybrid microfluidic chip. The structure of the platform consists of a three-dimensionally patterned polydimethylsiloxane top part attached to a bottom SU-8 epoxy-based negative photoresist part, where microelectrodes and optical fibers are incorporated to enable impedance and optical analysis. As a proof of concept, the chip functions have been tested and explored, enabling a diversity of applications: (i) impedance-based identification of the size of micro beads, as well as counting and distinguishing of erythrocytes by their volume or membrane properties; (ii) simultaneous determination of the refractive index and optical absorption properties of solutions; and (iii) fluorescence-based bead counting. © 2016 by the authors.

Molybdenum doped indium oxide (IMO) thin films were deposited on the glass substrates preheated to 450 °C by spray pyrolysis technique. The Mo doping was varied between 0 and 2.0 at.%. The films were characterized by their structural, electrical and optical properties. The films are confirmed to be cubic bixbyite In2O3 with a strongest orientation along (222) plane, which is shifted to (400) plane for the increase in Mo doping to 1.25 and 2 at.%. The film deposited with 0.5 at.% Mo doping shows high mobility of 76.9 cm2V- 1s- 1 , resistivity of 1.8 × 10- 3 Ω-cm and high carrier concentration of 4.6 × 1019 cm- 3 with 81.3% transmittance in the visible range between 500 and 800 nm. Further, the transparency extents well into the near-IR range. © 2008 Elsevier B.V. All rights reserved.

Molybdenum (0-1 at. %) doped indium oxide thin films with high near-infrared (NIR) transparency and high carrier mobility were deposited on Corning-1737 glass substrates at 400 °C by a spray pyrolysis experimental technique. X-ray diffraction (XRD) analysis confirmed the cubic bixbyite structure of indium oxide. The preferred growth orientation along the (222) plane for the low Mo doping level (0.5 at. %) shifts to (400) for higher Mo doping levels (<0.6 at. %). The crystallite size extracted from the XRD data corroborates the changes in full width at half maximum due to the variation in Mo doping. A scanning electron microscopy study illustrated the evolution in the surface microstructure as a function of Mo doping. The negative sign of the Hall coefficient confirmed the n -type conductivity. A high carrier mobility of ∼122.4 cm2 /V s, a carrier concentration of ∼9.5× 1019 cm-3, a resistivity of ∼5.3× 10-4cm, and a high figure of merit of ∼4.2× 10-2 -1 are observed for the films deposited with 0.5 at. % Mo. The obtained high average transparency of ∼83% in the wavelengths ranging from 400 to 2500 nm confirmed the extension of transmittance well into the NIR region. © 2009 American Institute of Physics.

This paper deals with high transparent and high conductive oxides based on polycrystalline titanium (Ti) doped (0.5-3 at.%) indium oxide (IO) thin films produced on glass substrates at 400 °C by spray pyrolysis technique. X-ray diffraction analysis confirmed the cubic bixbyite structure of indium oxide. A high mobility of ∼ 97 cm2 V- 1 s- 1, a carrier concentration of ∼ 1.55 × 1020 cm- 3 and a resistivity of ∼ 4.11 × 10- 4 Ω-cm with ∼ 83% of transmittance in the wavelength ranging between 400 and 2500 nm were obtained for 2 at.% Ti doping films, rivalling so to the best known transparent conducting oxide based on indium tin oxide. Moreover, the transmittance in the broad wavelength ranging between 400 and 2500 nm is over 83%, leading so to an increasing carrier generation towards the near infrared region of the spectrum, as required for applications such as solar cells. We also notice that increasing the doping concentration widened the optical band gap and caused a small Burstein-Moss shift, due to mobility decrease, as expected. © 2012 Published by Elsevier B.V.

Molybdenum-doped indium oxide (IMO) thin films were deposited at 450 °C for varying molybdenum concentrations in the range of 0.5-2 at% by the spray pyrolysis technique. These films confirmed the cubic bixbyite structure of polycrystalline In2O3. The preferred growth orientation along the (2 2 2) plane shifts to (4 0 0) on higher Mo doping levels. The films doped with 0.5 at% Mo showed high mobility of 76.9 cm2/(V s). The high visible transmittance extends well into the near-infrared region. A possibility of using the produced IMO films in nanocrystalline (nc) silicon solar cell applications is discussed in this article. The morphological studies showed a change in the microstructure, which is consistent with the change in crystallographic orientation. © 2008 Elsevier B.V. All rights reserved.

The aim of this paper is to present data on the dependence of the electro-optical characteristics and structure of n-type microcrystalline silicon films on the r.f. power used during the deposition of films produced by the plasma-enhanced chemical vapour deposition technique. The interest of these films arise from the fact that they combine some electro-optical advantages of amorphous (wide optical gap) and crystalline materials (electronic behaviour), highly interesting in the production of a wide variety of optoelectronic devices such as solar cells and thin film transistors. In this paper, microcrystalline n-type films presenting simultaneously optical gaps of about 2.3 eV, dark conductivity of 6.5 S cm-1 and Hall mobility of about 0.86 cm2 V-1 s-1 will be reported, the highest combined values for n-type microcrystalline silicon films, as far as we know. © 1997 Elsevier Science S.A.

Solution-processed p-type oxide semiconductors have recently attracted increasing interests for the applications in low-cost optoelectronic devices and low-power consumption complementary metal-oxide-semiconductor circuits. In this work, p-type nickel oxide (NiOx) thin films were prepared using low-temperature solution process and integrated as the channel layer in thin-film transistors (TFTs). The electrical properties of NiOx TFTs, together with the characteristics of NiOx thin films, were systematically investigated as a function of annealing temperature. By introducing aqueous high-k aluminum oxide (Al2O3) gate dielectric, the electrical performance of NiOx TFT was improved significantly compared with those based on SiO2 dielectric. Particularly, the hole mobility was found to be 60 times enhancement, quantitatively from 0.07 to 4.4 cm2/V s, which is mainly beneficial from the high areal capacitance of the Al2O3 dielectric and high-quality NiOx/Al2O3 interface. This simple solution-based method for producing p-type oxide TFTs is promising for next-generation oxide-based electronic applications. © 2016 Author(s).

A wide bandgap and highly conductive p-type hydrogenated nanocrystalline silicon (nc-Si:H) window layer was prepared with a conventional RF-PECVD system under large H dilution condition, moderate power density, high pressure and low substrate temperature. The optoelectrical and structural properties of this novel material have been investigated by Raman and UV-VIS transmission spectroscopy measurements indicating that these films are composed of nanocrystallites embedded in amorphous SiHx matrix and with a widened bandgap. The observed downshift of the optical phonon Raman spectra (514.4 cm-1) from crystalline Si peak (521 cm-1) and the widening of the bandgap indicate a quantum confinement effect from the Si nanocrystallites. By using this kind of p-layer, a-Si:H solar cells on bare stainless steel foil in nip sequence have been successfully prepared with a Voc of 0.90 V, a fill factor of 0.70 and an efficiency of 9.0%, respectively. © 2006 Elsevier B.V. All rights reserved.

Undoped and doped hydrogenated amorphous silicon semiconductors (a-Si:H) have been produced by a two consecutive decomposition deposition chamber (TCDDC) system assisted by electromagnetic static fields. Through this technique, a spatial separation is achieved between the plasma chemistry and that of the deposition to avoid ion and electron (with high energies) bombardment on the growing surface. Besides this, the use of a static magnetic field perpendicular to the substrate will promote plasma confinement, so avoiding its contamination by residual gases adsorbed on the reactor walls. On the other hand, the use of two grids dc biased in the deposition chamber, will allow control of the main film precursors, responsible for the electro-optical and structural properties of deposited films. In this paper we shall discuss the deposition method used as well as the transport, structural and morphological properties presented by deposited films and its dependence on deposition parameters used. © 1989.

The effect of oxygen partial pressure on the properties of In2 O3 - Ga2 O3 thin films produced by sputtering at room temperature aimed at thin film transistor (TFT) application is reported in this work. When produced in the absence of oxygen, the films are polycrystalline, while in the presence of oxygen, the films are amorphous. The films' resistivity is tuned between 10-3 and 104 γ cm. Moreover, the films present a high transmittance (> 80%) and a smooth surface (rrms =1.2 nm). The high performance as-produced transistors present high saturation mobility (μsat ≈43 cm2 /V s) and a subthreshold gate-voltage swing of 0.51 V/dec, which is reduced to 0.27 V/dec after 150°C annealing. © 2009 The Electrochemical Society.

Hydrogenated amorphous silicon photochemical sensors based on Pd-MIS structures were produced by Plasma Enhanced Chemical Vapor Deposition with two different oxidized surfaces (thermal and chemical oxidation). The behaviour of dark and illuminated current-voltage characteristics in air and in the presence of a hydrogen atmosphere is explained by the changes induced by the gases in the work function of the metal, modifying the electrical properties of the interface. The photochemical sensors produced present more than 2 orders of magnitude variation on the reverse dark current when in presence of 400 ppm hydrogen to which it corresponds a decrease of 45% on the open circuit voltage.

High mobility bottom gate thin film transistors (TFTs) with an amorphous gallium tin zinc oxide (a-GSZO) channel layer have been produced by rf magnetron cosputtering using a gallium zinc oxide (GZO) and tin (Sn) targets. The effect of the post annealing temperatures (200 °C, 250 °C and 300 °C) was evaluated and compared with two series of TFTs produced at room temperature and 150 °C during the channel deposition. From the results it was observed that the effect ofpos annealing is crucial for both series of TFTs either for stability as well as for improving the electrical characteristics. The a-GSZO TFTs operate in the enhancement mode (n-type), present a high saturation mobility of 24.6 cm2/Vs, a subthreshold gate swing voltage of 0.38 V/decade, a turn-on voltage of -0.5 V, a threshold voltage of 4.6 V and an ION/IOFF ratio of 8x107, satisfying all the requirements to be used in active-matrix backplane.

Transparent and highly conducting gallium-doped zinc oxide films were successfully deposited by rf sputtering at room temperature. The lowest resistivity achieved was 2.6×10-4 Ω cm for a thickness of 1100 nm (sheet resistance ≈1.6 Ω/sq), with a Hall mobility of 18 cm2/Vs and a carrier concentration of 1.3×1021 cm-3. The films are polycrystalline with a hexagonal structure and a strongly preferred orientation along the c-axis. A linear dependence between the mobility and the crystallite size was obtained. The films present a transmittance in the visible spectra between 80 and 90% and a refractive index of approximately 2, which is very close to the value reported for bulk material. © 2003 Elsevier B.V. All rights reserved.

In this paper we present results of indium zinc oxide deposited at room temperature by rf magnetron sputtering, with an electron mobility as high as 60 cm2/Vs. The films present a resistivity as low as 5 × 10 - 4 Ω cm with an optical transmittance of 85%. The structure of these films seems to be polymorphous (mix of different amorphous and nanocrystalline phases from different origins) as detected from XRD patterns with a smooth surface and from SEM micrographs, is highly important to ensure a long lifetime when used in display devices. © 2005 Elsevier B.V. All rights reserved.

Transparent electronics has gained special attention during the last few years and is today established as one of the most promising technologies for leading the next generation of flat panel display due to its excellent electronic performance. The key components are wide band gap semiconductors, where oxides of different origin play an important role, not only as passive component but also as active component, similar to what we observe in conventional semiconductors like silicon. In this paper we present the recent progress in n- and p-type oxide based thin film transistors (TFT) produced by rf magnetron sputtering and we will summarize the major milestones already achieved with this emerging and very promising technology. © 2015 IEEE.

The aim of this work is to present the main optoelectronic characteristics of large area 1D position sensitive detectors based on amorphous silicon p-i-n diodes. From that, the device resolution, response time and detectivity are derived and discussed concerning the field of applications of the 1D thin film position sensitive detectors.

High mobility bottom gate thin film transistors (TFTs) with an amorphous gallium tin zinc oxide (a-GSZO) channel layer have been produced by rf magnetron cosputtering using a gallium zinc oxide (GZO) and tin (Sn) targets. The effect of postannealing temperatures (200, 250, and 300 °C) was evaluated and compared with two series of TFTs produced at room temperature (S1) and 150 °C (S2) during the channel deposition. From the results, it was observed that the effect of postannealing is crucial for both series of TFTs either for stability as well as for improving the electrical characteristics. The a-GSZO TFTs (WL=5050 μm) operate in the enhancement mode (n -type), present a high saturation mobility of 24.6 cm2 V s, a subthreshold gate swing voltage of 0.38 V /decade, a turn-on voltage of -0.5 V, a threshold voltage of 4.6 V, and an Ion Ioff ratio of 8× 107, satisfying all the requirements to be used as active-matrix backplane. © 2008 American Institute of Physics.

Transparent and highly conducting gallium zinc oxide (GZO) films were successfully deposited by RF sputtering at room temperature. A lowest resistivity of∼2.8 × 10-4 ωcm was achieved for a film thickness of 1100nm (sheet resistance ∼2.5ω/□), with a Hall mobility of 18cm2/Vs and a carrier concentration of 1.3 × 1021 cm-3. The films are polycrystalline with a hexagonal structure having a strong crystallographic c-axis orientation. A linear dependence between the mobility and the crystallite size was obtained. The films are highly transparent (between 80% and 90% including the glass substrate) in the visible spectra with a refractive index of about 2, very similar to the value reported for the bulk material. These films were applied to single glass/TCO/pin hydrogenated amorphous silicon solar cells as front layer contact, leading to solar cells with efficiencies of about 9.52%. With the optimized deposition conditions, GZO films were also deposited on polymer (PEN) substrates and the obtained results are discussed. © 2008 Elsevier B.V. All rights reserved.

In this paper we present results of indium doped zinc oxide deposited at room temperature by rf magnetron sputtering, with electron mobility as high as 60 cm2/Vs. The films present a resistivity as low as 5×10 -4 Ωcm with an optical transmittance of 85%. The structure of these films look-like polymorphous (mixed of different amorphous and nanocrystalline phases from different origins) as detected from XRD patterns (no clear peak exists) with a high smooth surface, as detected from SEM micrographs, highly important to ensure long life time when used in display devices.

Staggered bottom gate transparent thin film transistors (TTFTs) have been produced by rf magnetron sputtering at room temperature, using amorphous indium zinc oxide (IZO) semiconductor, for the channel as well as for the drain and source regions. The obtained TTFTs operate in the enhancement mode with threshold voltages of 2.4 V, saturation mobility of 22.7 cm2/V s, gate voltage swing of 0.44 V/dec and an ON/OFF current ratio of 7 × 107. The high performances presented by these TTFTs produced at room temperature, make these TFTs a promising candidate for flexible, wearable, disposable portable electronics as well as battery-powered applications. © 2007 Elsevier Ltd. All rights reserved.