Rodrigo Martins

The first successful ablation of magnesium oxide through a home-made continuous-wave Cr:Nd:YAG ceramic solar laser is reported. A stationary heliostat-parabolic mirror solar energy collection and concentration system was used. A stable continuous-wave laser output power of 19.2 W was attained with laser beam brightness figure of merit 7.6 times higher than that of the previous scheme, enabling therefore the direct ablation of pure magnesium by our solar-pumped laser with only 1.6 m2 effective collection area. This could be an important step towards renewable magnesium production, offering multiple advantages, such as reducing agent avoidance, in relation to that of the previous Fresnel lens Cr:Nd:YAG continuous-wave solar laser system. © 2016 Elsevier B.V.

Titanium dioxide was synthesized on glass substrates from titanium (IV)isopropoxide and hydrochloride acid aqueous solutions through microwave irradiation using as seed layer either fluorine-doped crystalline tin oxide (SnO2:F) or amorphous tin oxide (a-SnOx). Three routes have been followed with distinct outcome: (i) equimolar hydrochloride acid/water proportions (1HCl:1water) resulted in nanorod arrays for both seed layers; (ii) higher water proportion (1HCl:3water) originated denser films with growth yield dependent on the seed layer employed; while (iii) higher acid proportion (3HCl:1water) hindered the formation of TiO2. X-ray diffraction (XRD) showed that the materials crystallized with the rutile structure, possibly with minute fractions of brookite and/or anatase. XRD peak inversions observed for the materials synthesized on crystalline seeds pointed to preferred crystallographic orientation. Electron diffraction showed that the especially strong XRD peak inversions observed for TiO2 grown from the 1HCl:3water solution on SnO2:F originated from a [001] fiber texture. Transmittance spectrophotometry showed that the materials with finer structure exhibited significantly higher optical band gaps. Photocatalytic activity was assessed from methylene blue degradation, with the 1HCl:3water SnO2:F material showing remarkable degradability performance, attributed to a higher exposure of (001) facets, together with stability and reusability. © 2015 Elsevier B.V.

Photocurrent enhancement in thin a-Si:H solar cells due to the plasmonic light trapping is investigated, and correlated with the morphology and the optical properties of the selfassembled silver nanoparticles incorporated in the cells' back reflector. © 2014 Optical Society of America.

Thin-films of copper oxide Cu O were produced by thermal oxidation of metallic copper (Cu) at different temperatures (150-450 C). The films produced at temperatures of 200, 250 and 300 C showed high Hall motilities of 2.2, 1.9 and 1.6 cm V s , respectively. Single Cu O phases were obtained at 200 C and its conversion to CuO starts at 250 C. For lower thicknesses 40 nm, the films oxidized at 250 C showed a complete conversion to CuO phase. Successful thin-film transistors (TFTs) were produce by thermal oxidation of a 20 nm Cu film, obtaining p-type Cu O (at 200 C) and CuO (at 250 C) with On/Off ratios of 6 10 and 1 10 , respectively. © 2005-2012 IEEE.

In this paper we report results concerning the use of paper as substrate and as an electronic component for the next generation of sustainable low cost electronic systems, where different examples of applications are given. © 2013 Society for Information Display.

In this work, we report results concerning the performances of thin-film transistors (TFTs) where the channel layer is based on microcrystalline zinc tin oxide (ZTO) processed by spray pyrolysis technique. TFTs made with 30 nm thick ZTO channel layer deposited at a substrate temperature of 400 C and 300 Cexhibited, respectively, a saturation mobility of 2.9 cm V s and 1.45 cm V s ; voltage of 0.15 V, and 0.2 V; a sub-threshold swing of 400 mV/dec and 500 mV/dec; ON/OFF ratio at the onset of hard saturation current of 3.5 10 and 6 10 , for a drain to source voltage of 10 V (close to or below the gate to source voltage). This indicates that the substrate temperature is relevant in determining the devices' electronic performances. © 2013 IEEE.

The effect of post-deposition annealing temperature on the pH sensitivity of room temperature RF sputtered +{\hbox{Ta}}-{2}{\hbox{O}}5 was investigated. Structural and morphological features of these films were analyzed before and after annealing at various temperatures. The deposited films are amorphous up to 600 +^{\circ}{\hbox{C}}+ and crystallize at 700 +^{\circ}{\hbox{C}}+ in an orthorhombic phase. Electrolyte-insulator- semiconductor (EIS) field effect based sensors with an amorphous +{\hbox{Ta}}-{2}{\hbox{O}}5 sensing layer showed pH sensitivity above 50 mV/pH. For sensors annealed above 200 +^{\circ}{\hbox{C}}+ pH sensitivity decreased with increasing temperature. Stabilized sensor response and maximum pH sensitivity was achieved after low temperature annealing at 200 +^{\circ}{\hbox{C}}+ , which is compatible with the use of polymeric substrates and application as sensitive layer in oxides TFT-based sensors. © 2005-2012 IEEE.

In this work Laponite was combined with a modified abundant natural polymer, (caboxymethyl cellulose), acrylic sodium salt polymer and lithium perchlorate aiming to produce inexpensive and sustainable nanocomposite electrolytes for functional electrochemical devices. Optical, electrochemical, structural, morphological and rheological characterization was performed in order to evaluate their properties and potential advantages as electrolyte. It was verified that the addition of Laponite led to an ionic conductivity at room temperature (25 C) in the range of 6 to 9 × 10- 5 Scm - 1 this value being then determined by the composition of the nanocomposite. These electrolytes were applied to electrochromic devices using evaporated nickel oxide thin film as the electrochromic layer. The devices exhibited a significant transmittance modulation that exceeds 45 % at 600 nm. © 2013 Elsevier B.V.

Thin-films of copper oxide Cu x were sputtered from a metallic copper (Cu) target and studied as a function of oxygen partial pressure. A metallic Cu film with cubic structure obtained from 0% O PP has been transformed to cubic Cu x phase for the increase in O PP to 9% but then changed to monoclinic CuO phase (for. The variation in crystallite size (calculated from x-ray diffraction data) was further substantiated by the variation in grain size (surface microstructures). The Cu x films produced with O PP ranging between 9% and 75% showed p-type behavior, which were successfully applied to produce thin-film transistors. © 2006 IEEE.

P-type thin-film transistors (TFTs) using room temperature sputtered tin and copper oxide as a transparent oxide semiconductor have been produced on rigid and paper substrates. The SnO x films shows p-type conduction presenting a polycrystalline structure composed with a mixture of tetragonal β-Sn and α-SnO x phases, after annealing at 200°C. These films exhibit a hole carrier concentration in the range of ≈ 10 16-10 18 cm -3, electrical resistivity between 101-102 Ωcm, Hall mobility of 4.8 cm 2/Vs, optical band gap of 2.8 eV and average transmittance ≈ 85 % (400 to 2000 nm). Concerning copper oxide Cu xO thin films they exhibit a polycrystalline structure with a strongest orientation along (111) plane. The Cu xO films produced between an oxygen partial pressure of 9 to 75% showed p-type behavior, as it was measured by Hall effect and Seebeck measurements. The bottom gate p-type SnO x TFTs present field-effect mobility above 1.24 cm 2/Vs (including the paper p-type oxide TFT) and an on/off modulation ratio of 10 3 while the Cu xO TFTs exhibit a field-effect mobility of 1.3×10 -3 cm 2/Vs and an on/off ratio of 2×10 2. © 2012 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

In this paper we report on the fabrication and performance of a portable and low cost optoelectronic platform integrating a double color tuned light emitting diode as light source, an amorphous/nanocrystalline silicon photodetector with a flat spectral response in the wavelength range from 520. nm to 630. nm and integrated electronic for signal acquisition and conditioning constituted by current to voltage converter, a filter and an amplification stage, followed by an analog to digital converter, with appropriate software for full automation to minimize human error. Incorporation of the double color tuned light emitting diode provides for a simple yet innovative solution to signal acquisition independently from the light intensity and/or solution concentration, while considerably decreasing production costs. Detection based on Au-nanoprobes constitutes the biorecognition step and allowed identification of specific sequences of Mycobacterium tuberculosis complex, namely Mycobacterium bovis and M. tuberculosis in biological samples. © 2010 Elsevier B.V.

In order to study the properties of P-doped ZnO films deposited at low temperature substrates, P-doped ZnO films were RF-sputtered on sapphire substrates in the range from RT to 350°C. XRD spectra indicated the growth of the crystallites along the strongest <001> orientation. Further ZnO (002) peak became the weakest when the film was sputtered at 250°C. AFM pictures showed that the surface morphology varied with the deposition temperature. The sample RMS increased with the increase of substrate temperature. XPS spectra showed a clear broad P 2p peak at about 134 eV. Further the film composition varied with the substrate temperature. The average visible transmittance calculated in the wavelength ranging 400-600 nm was more than 60%. The optical band gap calculated from the absorption coefficient was about 3.2 eV. The Hall measurements confirm the n-type conductivity of the films. The carrier concentration in the films decreases with the increase of substrate temperature. The study is helpful for understanding the properties of P-doped ZnO films sputtered at lower substrate temperature and achieving p type ZnO films at lower temperature.

Long-term electrical stability measurements, including current/bias stress and aging over 18 months of idle shelf life are presented for GIZO-based TFTs. The effects of oxygen partial pressure, annealing temperature and passivation are discussed. Optimized devices show highly stable properties, such as a recoverable ΔVT<0.5 V after 24h of 1D=10 μA stress, quite promising for integration in electronic circuits.

Long-term electrical stability measurements, including current/bias stress and aging over 18 months of idle shelf life are presented for GIZO-based TFTs. The effects of oxygen partial pressure, annealing temperature and passivation are discussed. Optimized devices show highly stable properties, such as a recoverable ΔV T<0.5 V after 24h of I D=10 μA stress, quite promising for integration in electronic circuits. © 2010 SID.

The aim of this research is to study the role of concentration variations on precursor solution of nitrogen doped ZnO (ZnO:N) thin films which has been prepared by spray pyrolysis technique. SEM micrographs show that ZnO:N films in 0.1 ML concentration have a mono-disperse surface with nano-spheres of 50 nm in diameter. In higher molarities the nano-spheres agglomerate leading to particle formation. For 0.4 ML concentrations this change is observed, where plume like particles are seen over the surface of ZnO:N thin film. This change corresponds also to changes observed in the XRD spectra, where crystal orientation of ZnO:N thin films changes from (002) to (100). All of the ZnO:N thin films have kept their sharp ultra violet absorption edge, but the transparency in visible spectra region decreases as the molarities in precursor solution increase. Photoluminescence spectra at room temperature revealed emissions at 2.33 eV, 2.54 eV and 3.16 eV that can be attributed to the presence of nitrogen in ZnO structure. We also observe that all samples analyzed show a p-type Hall effect behavior, and that as the molarities in the precursor solution increase, the electrical resistivity of the films decreases, due to an enhancement of free carriers, while the mobility decreases. These data prove the capability of spray pyrolysis as a viable technique in preparing p-type TCO materials and so, fully transparent CMOS-like devices. © 2009 Elsevier B.V. All rights reserved.

In this paper we report the use of a sheet of cellulose fiber-based paper as the dielectric layer used in oxide based semiconductor thin film field-effect transistors (FETs). In this new approach we are using the cellulose fiber-based paper in an "interstate" structure since the device is build on both sides of the cellulose sheet. Such hybrid FETs present excellent operating characteristics such as high channel saturation mobility (>30 cm 2/Vs), drain-source current on/off modulation ratio of approximately 104, near-zero threshold voltage, enhancement n-type operation and sub-threshold gate voltage swing of 0.8 V/decade. The cellulose fiber-based paper FETs characteristics have been measured in air ambient conditions and present good stability. The obtained results outpace those of amorphous Si TFTs and rival with the same oxide based TFTs produced on either glass or crystalline silicon substrates. The compatibility of these devices with large-scale/large-area deposition techniques and low cost substrates as well as their very low operating bias delineates this as a promising approach to attain high-performance disposable electronics like paper displays, smart labels, smart packaging, RFID and point-of-care systems for self analysis in bio-applications, among others. © 2009 SPIE.

High performance transparent thin-film transistors deposited on glass substrates and entirely processed at a low temperature not exceeding 150°C are presented and analyzed in this paper. Besides being based on an amorphous oxide semiconductor, the main innovation of this work relies on the use of sputtered multicomponent oxides as dielectric materials based on mixtures of Ta2O5 with SiO2 or Al2O3. These multicomponent dielectrics allow to obtain amorphous structures and low leakage currents while preserving a high dielectric constant. This results in transistors with remarkable electrical properties, such as field-effect mobility exceeding 35 cm2 V-1 s-1, close to 0 V turn-on voltage, on/off ratio higher than 106, and a subthreshold slope of 0.24 V decade-1, obtained with a Ta2O5: SiO2 dielectric. When subjected to severe current stress tests, optimized devices show little and reversible variation in their electrical characteristics. The devices presented here have properties comparable to the ones using plasma-enhanced chemical vapor deposited SiO2 at 400°C, reinforcing the success of this amorphous multicomponent dielectric approach for low temperature, high performance, and transparent electronic circuits. © 2009 The Electrochemical Society.

The authors report on the performance of polymer-based light-emitting diodes, LEDs, using amorphous zinc oxide-doped indium oxide, IZO, as anode. In particular, LEDs with poly[(2-methoxy-5-(2′-ethyl-hexyloxy)-1,4-phenylene vinylene] as electroluminescent layer and aluminium cathodes, show higher efficiency with this IZO anode (0.015 cd/A) than with indium-tin oxide (ITO) (0.010 cd/A). Inspite of the higher resistance of this IZO electrode, compared with ITO, the fact that it can be processed at lower temperatures and allows similar or even higher efficiency values for polymer LEDs make this material a good candidate for display and other optoelectronic applications. © 2009 Elsevier B.V. All rights reserved.

The driving force behind the work herein presented is the importance of budgeting in a competitive market. The problem at hands is the creation of a budgeting methodology for reverse engineering applications, involving laser scanning, that has the ability to generate budgets for different customer accuracy requirements and for parts of different morphologic characteristics, such as: shape, dimension and/or detail complexity. A breakup approach was used to implement the methodology: the reverse engineering process was broken in nine basic identified steps and elementary sources of cost were defined at the different reverse engineering stages as well. Particular budgeting methodologies for each step of the process were created. The obtained results so far point to the possibility of creating a complete budgeting system based on the proposed methodology. © 2008 Taylor & Francis Group.

Thin films of molybdenum-doped indium oxide (IMO) were prepared by a 3-source, cylindrical radio-frequency magnetron sputtering at room temperature. The films were post-annealed and were characterized by their structural (X-ray diffraction) and optical (UV-VIS-NIR spectrophotometer) properties. The films were studied as a function of oxygen volume percentage (O2 vol.%) ranging from 3.5 to 17.5. The structural studies revealed that the as-deposited amorphous films become crystalline on annealing. In most cases, the (222) reflection emerged as high intensive peak. The poor visible transmittance of the films as-deposited without oxygen was increased from ∼ 12% to over 80% on introducing oxygen (3.5 O2 vol.%). For the films annealed in open air, the average visible transmittance in the wavelength ranging 400-800 nm was varied between 77 and 84%. The films annealed at high temperatures (> 300 °C) decreased the transmittance to as low as < 1%. The optical band gap of the as-deposited films increased from the range 3.83-3.90 to 3.85-3.98 eV on annealing at different conditions. © 2007 Elsevier B.V. All rights reserved.

This paper presents the performances of an in-line plasma enhanced chemical vapor deposition system constituted by 5 chambers and one external unloaded chamber used in the simultaneous manufacturing of 4 large (30 cm × 40 cm) solar cells deposited on glass substrates. The system is fully automatically controlled by a Programmable Logic Controller using a specific developed software that allows devices mass production without losing the flexibility to perform process innovations according to the industrial requests, i.e. fast and secure changes and optimizations. Overall, the process shift is of about 15 min per each set of 4 solar cells. Without a buffer layer, solar cells with efficiencies of about 9% were produced by the proper tuning of the i-layer production conditions. © 2005 Elsevier B.V. All rights reserved.

In this work metal induced crystallization (MIC) using nickel (Ni) was employed to obtain poly-Si by crystallization of amorphous films for application as active layer in TFTs. Ni layers with thicknesses of 0.5 nm, 1 nm and 2 nm were used to crystallize the silicon. The TFTs were produced with a bottom gate configuration using a multi-layer Al2O3/TiO2 insulator produced by atomic layer deposition (ALD) as gate dielectric. The best performances of the TFT produced were obtained when using very thin Ni layers for the crystallization. This is attributed to a lower metal contamination and to the enhancement of grain size, as a result of the lower nucleation density achieved, when using the thinnest Ni layer. Devices that exhibit effective mobility of 45.5 cm2V-1s-1 and an on/off ratio of 5.55×104 were produced using a 0.5 nm Ni layer to crystallize the active channel area.

In this paper we present results of intrinsic/non-doped zinc oxide deposited at room temperature by radio frequency magnetron sputtering able to be used as a semiconductor material on electronic devices, like for example ozone gas sensors, ultra-violet detectors and thin film transistors. These films present a resistivity as high as 2.5×108 Ω cm with an optical transmittance of 90%. Concerning the structural properties, these films are polycrystalline presenting a uniform and very smooth surface. © 2005 Elsevier B.V. All rights reserved.