Rodrigo Martins

The aim of this work is to study the electrical characteristics of polycrystalline silicon (poly-Si) thin film transistors (TFTs) using spectroscopic impedance technique, where the poly-Si active layer was obtained by metal induced crystallization of amorphous silicon. From the study performed a theoretical model that fitted the impedance data is proposed, in order to obtain the separate contributions of each region that constitutes the TFT namely the channel, non accumulated region and contacts. © 2006 Elsevier B.V. All rights reserved.

Two self-buffer layers were grown on c-plane sapphire substrates by atmospheric MOCVD method using DEZn, tert-butanol as precursors and H 2 as carrier gas. Then, they were respectively annealed in growth process and oxygen environment. After that, ZnO films were respectively grown on them. XRD spectra show that all the films were grown in [002] orientation. Furthermore, the film with a buffer layer annealed in oxygen exhibits much higher crystal quality. Its FWHM of the rocking curve is only 567arcsec. Furthermore, its Raman scattering spectrum appears a much stronger E2 mode peak at 436cm-1 and its PL spectrum appears a shoulder at 3.367eV on the higher energy side. © 2006 WILEY-VCH Verlag GmbH & Co. KGaA,.

ZnO films with and without a self-buffer layer were grown on c-plane sapphire substrates by atmospheric metal organic chemical vapor deposition. The influence of the buffer layer thickness, annealing temperature and annealing time on ZnO films has been investigated. The full width at half maximum of the ω-rocking curve of the optimized self-buffer layer sample is only 395 arc sec. Its surface is composed of regular columnar hexagons. After the buffer layer was introduced, the A1 longitudinal mode peak at 576 cm- 1, related to the defects, disappears in Raman spectra. For the photoluminescence, besides the strong donor binding exciton peak at 3.3564 eV, an ionized donor binding exciton and a free exciton peak is respectively observed at 3.3673 and 3.3756 eV at the high-energy side in the spectrum of the sample with the buffer layer. © 2006 Elsevier B.V. All rights reserved.

Multicomponent amorphous oxides are starting to emerge as a class of appealing semiconductor materials for application in transparent electronics. In this work, a high performance bottom-gate n-type transparent thin-film transistors are reported, being the discussion primarily focused on the influence of the indium zinc oxide active layer thickness on the properties of the devices. For this purpose, transparent transistors with active layer thicknesses ranging from 15 nm to 60 nm were produced at room temperature using rf magnetron sputtering. Optical transmittance data in the visible range reveals average transmittance higher than 80%, including the glass substrate. The devices work in the enhancement mode and exhibit excellent saturation drain currents. On-off ratios above 107 are achieved, but this value tends to be lower for devices with thicker semiconductor films, as a result of the decrease in the resistance of the channel region with increasing thickness. Channel mobilities are also quite respectable, with some devices presenting values around 40 cm2/V s, even without any annealing or other post-deposition improvement processes. Concerning the evolution of threshold voltage with the thickness, this work shows that it increases from about 3 V in thicker films up to about 10 V in the thinnest ones. The interesting electrical properties obtained and the versatility arising from the fact that it is possible to modify them changing only the thickness of the semiconductor makes this new transparent transistors quite promising for future transparent ICs. © 2006 Elsevier B.V. All rights reserved.

In this work we present a study concerning the influence of some of the most important external factors on the electrical properties of transparent thin-film transistors (TFTs), using zinc oxide produced at room temperature as the semiconductor material. Electrical characterization performed sixteen months after the production of the devices showed a decrease in the on/off ratio from 8×105 to 1×105, mainly due to the increase of the off-current. We also observed a small increase in the saturation mobility, a decrease in the threshold voltage and an increase in the gate voltage swing (by factors of about 1.2, 0.9 and 1.6, respectively). Exposure to ambient light does not have a noticeable effect on the electrical properties, which is an important point as regards the application of these devices in active matrix displays. Some variation of the electrical properties was only detectable under intense white light radiation. In order to evaluate the temperature effect on the TFTs, they were also characterized at 90 °C. At this temperature we noticed that the off-current increased more than two times, and the other electrical properties had a small variation, returning to their initial values after cooling, meaning that the process is totally reversible. © 2005 Elsevier Ltd. All rights reserved.

This work aims to report results of the spatial and frequency optical detection limits of integrated arrays of 32 one-dimensional amorphous silicon thin film position sensitive detectors with nip or MIS structure, under continuous and pulsed laser operation conditions. The arrays occupy a total active area of 45 mm2 and have a plane image resolution better than 15 μm with a cut-off frequency of about 6.8 kHz. The non-linearity of the array components varies with the frequency, being about 1.6% for 200 Hz and about 4% for the cut-off frequency (6.8 kHz).

This paper presents the results achieved in optimized 1D position sensitive detectors (PSD) using a metal-insulator-semiconductor (MIS) structure and different length to width ratios, in order to determine the optimal geometrical factor for the desired 3D integration. The results show that the optimized MIS PSD produced, exhibited linearity errors as low as 0.8% and sensitivities of 32 mV/cm, for a 5 mW spot beam intensity at a wavelength of 532 nm. The sensors can achieve a longitudinal spatial resolution of 1.25 μm (estimated by modulation transfer function calculation), while the transverse resolution depends on the minimum width used for each sensor. The calculated Jones parameter of the sensors is higher than 1011 J, with a fall-off parameter of 0.012 cm-1, indicating a high signal to noise detection ratio. © 2006 Elsevier B.V. All rights reserved.

In this work we study the optical and electrical behavior of ZnO:Ga, ITO and IZO films deposited on glass after sustaining different hydrogen plasma conditions and exposure times. This work was complemented by analyzing the surface morphology of the set of films, which allow us to determine the role of hydrogen plasma on the film's properties such as Hall mobility, free carrier concentration, sheet resistance, optical transmittance, figure of merit and state of the surface. Apart from that, the performances of solar cells using an intrinsic layer constituted by nanocrystalline silicon will be also presented. The data show that the electrical properties of solar cells were improved by using ZnO:Ga as front contact, allowing a high current density collection and single pin solar cells with efficiencies exceeding 11%. © 2005 Materials Research Society.

In this work, metal induced crystallization using nickel was employed to obtain polycrystalline silicon by crystallization of amorphous films for thin film transistor applications. The devices were produced through only one lithographic process with a bottom gate configuration using a new gate dielectric consisting of a multi-layer of aluminum oxide/titanium oxide produced by atomic layer deposition. The best results were obtained for TFTs with the active layer of poly-Si crystallized for 20 h at 500 °C using a nickel layer of 0.5 nm where the effective mobility is 45.5 cm2 V-1 s-1. The threshold voltage, the on/off current ratio and the sub-threshold voltage are, respectively, 11.9 V, 5.55×104 and 2.49 V/dec. © 2005 Elsevier B.V. All rights reserved.

The aim of this work is to present data concerning the optimization of performances of a large area amorphous silicon p-i-n solar cell (30×40 cm2) deposited by plasma enhanced chemical vapour deposition (PECVD) at 27.12 MHz. In this work the solar cell was split into small areas of 0.126 cm2, aiming to study the device performance uniformity, where emphasis was put on the role of the n-layer thickness. The solar cells were studied through the spectral response behaviour in the 400-750 nm range as well as by the behaviour of the AC impedance. Solar cells with fill factor of 0.58, open circuit voltage of 0.83 V, short circuit current density of 17.14 mA/cm2 and an efficiency of 8% were obtained at growth rates higher than 0.3 nm/s. © 2004 Elsevier B.V. All rights reserved.

In this work we have focused our attention on the role of the gas mixture (O2/Ar) used during HfO2 thin film processing by r.f. magnetron sputtering, to produce dielectrics with suitable characteristics to be used as gate dielectric. Increasing the O2/Ar ratio from 0 to 0.2, the films properties (optical gap, permittivity, resistivity and compactness) are improved. At these conditions, films with a band gap around 5 eV were produced, indicating a good stoichiometry. Also the flat band voltage has a reduction of almost three times indicating also a reduction of the same order on the fixed charge density at the semiconductor-insulator interface. The dielectric constant is around 16 which is very good, since the surface of the silicon where the HfO2 films were deposited contains a SiO 2 layer of about 3 nm that gives an effective dielectric constant above 20, close to the HfO2 stoichiometric value (∼25). Further increase on the O2/Ar ratio does not produce significant improvements. © 2004 Elsevier B.V. All rights reserved.

This work refers to the electro-optical and structural characteristics of titanium oxide (TiOx) thin films produced by radio frequency (r.f.) magnetron sputtering that present promising performances for gate dielectric applications, alone or in mixed tandem structures, such as with Al yOz films, taking advantage of its high dielectric constant. Films produced with a O2/Ar ratio between 0.1 and 0.15 present an improved stochiometry and density where the resistivity overcomes 1011 Ω cm and the fixed charge density decreases below 10 12 cm-2. The deposition pressure influences greatly the growth rate that seems to be a determinant factor dictating the films properties. © 2004 Elsevier Ltd. All rights reserved.

The variation of the structure, morphology and the electrical properties of thin amorphous silicon films caused by Rapid Thermal Annealing is studied. The films annealed at 1200°C for 2 minutes change their structure to polycrystalline and as a result their resistivity decreases by 4 orders of magnitude. Due to the small thickness of the as deposited amorphous silicon the obtained poly-Si is strongly irregular and has many discontinuities in its texture.

Highly conducting and transparent gallium doped zinc oxide thin films have been deposited at high growth rates by r.f. magnetron sputtering at room temperature on inexpensive soda lime glass substrates. The argon sputtering pressure was varied between 0.15 and 2.1 Pa. The lowest resistivity was 2.6 × 10-4 Ω cm (sheet resistance ≈6 Ω/sq. for a thickness ≈600 nm) and was obtained at an argon sputtering pressure of 0.15 Pa and a r.f. power of 175 W. The films present an overall transmittance in the visible spectra of approximately 90%. The increase on the resistivity for higher sputtering pressures is due to a decrease of both, mobility and carrier concentration, and is associated to a change on the surface morphology. The low resistivity, accomplished with a high growth rate (290 Å/min) and with a room temperature deposition enables these films deposition onto polymeric substrates for flexible optoelectronic devices. © 2002 Elsevier Science B.V. All rights reserved.

In this work we show that it is possible to control the plasma regime in the region close to the substrate in r.f. silane discharges. The PECVD reactor works in a modified triode configuration, where the control over the plasma regime is performed by polarising a grid electrode, placed close to the r.f. electrode, with a DC power source. Besides that, the DC grid allows also to control the energy of the ion bombardment, because the plasma potential will be a function of the voltage (Vpol) applied to the DC grid. The silane plasma was characterised with a Langmuir probe and an impedance probe. We were able to identify three plasma regimes in the region close to the substrate: γ′ regime for Vpol<0 V; γ′-α regime for 0 V<Vpol<40 V; and α regime for Vpol40 V. The γ′ regime is associated with a high concentration of dust particles in plasma and high electron energy (≈8eV), while the α regime is associated with a free dust plasma and low electron energy (≈2eV). The intermediate regime, γ′-α, is characterised by the presence of smaller particles (≈2-5nm) that can be beneficial for the film's properties. © 2002 Elsevier Science Ltd. All rights reserved.

P- and n-type silicon thin films have been produced using a new hot wire plasma assisted deposition process that combines the conventional plasma enhanced chemical vapor deposition and the hot wire techniques. The films were produced in the presence of different hydrogen gas flow and their optoelectronic, structural and compositional properties have been studied. The optimized optoelectronic results achieved for n-type Si:H films are conductivity at room temperature of 9.4(Ωcm)-1 and optical band gap of 2eV while for p-type SiC:H films these values are 1 × 10-2(Ωcm)-1 and 1.6eV, respectively. The films exhibit the required optoelectronic characteristics and compactness for device applications such as solar cells.

In this paper a set of one-dimensional simulations of a-Si:H p-i-n junctions under different illumination conditions and with different intrinsic layer are presented. The simulation program ASCA permits the analysis of the internal electrical behaviour of the cell allowing a comparison among the different internal configurations determined by a change in the input set. Results about the internal electric configuration will be presented and discussed outlining their influence on the current tension characteristic curve. Considerations about the drift-diffusion and the generation-recombination balance distributions, outlined by the simulation, can be used to explain the correlation between the basic device output, the i-layer characteristics (thickness and DOS), the incident radiation intensity and photon energy. © 2002 Elsevier Science B.V. All rights reserved.

In this work we show that it is possible to control the plasma species present near the substrate surface, from what is usually associated with an α regime (a plasma free of particles) to a γ' regime (a plasma where particles are present) and simultaneously control the energy of the ions striking the substrate during a-Si:H deposition from a silane glow discharge in a modified triode (MT) type PECVD reactor, where a DC mesh electrode biased with Vpol is located in front of the r.f electrode. The presence of large particles in the plasma leads to the deposition of the films with the poorest optoelectronic properties. When the particle size in the plasma decrease the film properties improve, but, when particles are no longer present in the plasma region close to the substrate, like in a α like regime, the properties of the films deteriorate again. The results show that the best transport properties are achieved for the films deposited in the α-γ' transition regime corresponding to 0V<Vpol<51V. Under this condition the films present a dark conductivity, σ d ≈ 10-11 (Ωcm)-1, photosensitivity, S ≈ 107, activation energy, ΔE ≈ 0.9 eV, hydrogen content, CH ≈ 10%, factor of microstructure, R ≈ 0.085 and an optical gap, Eop ≈ 1.77 eV.

Tensile tests were performed on PET films coated with Al doped zinc oxide films by RF magnetron sputtering. During the tensile elongation, the electrical resistance of the oxide was evaluated in situ. The results indicate that the increase in the electrical resistance is related to the crack debsity and crack width, which also depends on the film thickness.

The effect of annealing treatment (in the presence of different types of atmospheres) on the performances of zinc oxide thin films (intrinsic and doped with In and Al) prepared by spray pyrolysis have been studied, with the aim to determine more adequate conditions to improve the properties of the films. The results show that the annealing treatment leads to substantial changes in the structural, electrical and optical characteristics of ZnO thin films. The most significant improvements were obtained after annealing in forming gas (reduction atmosphere) at 200°C during 2 h. The ZnO:In film after heat treatment was the one that exhibited the lowest resistivity (p=5.2x10-2 ωcm) and a high transmittance (T=86%). © 2001 Elsevier Science Ltd. All rights reserved.

In this work we present preliminary results on the sensitivity to methane gas of zinc oxide thin films deposited by spray pyrolysis. It was found that using highly resistive (above 104 Ω cm) thin films and by performing the measurements at 200°C a sensitivity better than one order of magnitude was found to detect 2000 ppm of methane. A linear dependence on the sensitivity between 100 and 2000 ppm of methane was also obtained. © 2001 Elsevier Science Ltd. All rights reserved.

{In this work we report how it is possible to control the plasma regime near the substrate surface, from predominantly α to predominantly γ', passing trough and intermediate α-γ' regime, and simultaneously control the energy of the ions striking the substrate during a-Si:H deposition from a silane glow discharge in a modified triode type PECVD reactor. To do so, we apply a DC voltage (Vpol to a set of grids placed in front of the r.f. electrode and by doing this, we control the energy of the ions striking the substrate during the film's growth and the plasma regime near the substrate. Under a plasma of the γ' regime, the surface roughness is high and the films are poorly compact. In the α-γ' regime, the ion bombardment is moderate and the films are highly smooth and compact. In the α regime the ion bombardment is higher and so the films can become more compact but the surface roughness increases and the electrical properties deteriorate. The results achieved show that the best transport properties are achieved for the films deposited in the α-γ' regime corresponding to a Vpol of 38 V. Under this condition the films presented a dark conductivity, σd = 6.2×10-12 (Ωcm)-1, activation energy, ΔE ≈ 0.9 eV, hydrogen content

In this work a study of the influence of the annealing treatment (atmosphere and temperature) on the properties of zinc oxide thin films (intrinsic and doped with indium and aluminum) prepared by spray pyrolysis is presented. The result shows that the type of atmosphere (reduction or oxidant) has an important role in the changes observed in the structural, electrical and optical properties of the ZnO thin films. The ZnO thin film doped with indium, presents the lowest resistivity (ρ = 5.8×10-3 Ωcm) associated to a high transmittance (T = 86%), characteristics required for application on optoelectronic devices.

This paper presents results of the role of the oxygen concentration (CO) and the deposition pressure (pd) on structural and electrical properties of indium tin oxide films produced by r.f. magnetron sputtering. The films were annealed in air, followed by a reannealed stage in hydrogen, aiming to improve the film's transparency and conductivity. The results achieved show that the films texture grain size, structure and compactness is more influenced by CO than by pd, the same does not happen with the electrical properties.

This paper deals with a new design method for the interfaces of a-Si:H pin solar cells that improves the stability and performances of devices deposited in a single batch chamber process. The method consists in removing a deposited sacrificial layer placed between the p/i and/or i/n interfaces by etching. This layer is an absorber of defects and impurities that are introduced in the interfaces, mainly from the chamber walls cross-contamination and the substrate surface. The results achieved increase the device fill factor and short circuit current density, respectively towards 75% and 16.3 mA cm-2, with a final efficiency of about 10%, before light soaking experiments. © 2000 Elsevier Science B.V. All rights reserved.