Rodrigo Martins

This new production technique is based on the growth of a-Si films on a reactor where gas decomposition promoted by a capacitively coupled r. f. power system takes place in a chamber separated from that where amorphous films are deposited under the action of an electromagnetic static field. Using this method, we shall reduce films contamination caused by the residual gas desorbed from reactor walls. At the same time, there is a reduction plasma ion and electron damages on the deposited films. The main species impinging upon our substrates will be mainly composed of long life radicals with high mobilities and high diffusion rates, which will give origin to a random silicon network free of long poly-silane chains.

Today there is a strong interest in the scientific and industrial community concerning the use of biopolymers for electronic applications, mainly driven by low-cost and disposable applications. Adding to this interest, we must recognize the importance of the wireless auto sustained and low energy consumption electronics dream. This dream can be fulfilled by cellulose paper, the lightest and the cheapest known substrate material, as well as the Earth's major biopolymer and of tremendous global economic importance. The recent developments of oxide thin film transistors and in particular the production of paper transistors at room temperature had contributed, as a first step, for the development of disposable, low cost and flexible electronic devices. To fulfil the wireless demand, it is necessary to prove the concept of self powered devices. In the case of paper electronics, this implies demonstrating the idea of self regenerated thin film paper batteries and its integration with other electronic components. Here we demonstrate this possibility by actuating the gate of paper transistors by paper batteries. We found that when a sheet of cellulose paper is covered in both faces with thin layers of opposite electrochemical potential materials, a voltage appears between both electrodes - paper battery, which is also self-regenerated. The value of the potential depends upon the materials used for anode and cathode. An open circuit voltage of 0.5V and a short-circuit current density of 1μA/cm2 were obtained in the simplest structure produced (Cu/paper/Al). For actuating the gate of the paper transistor, seven paper batteries were integrated in the same substrate in series, supplying a voltage of 3.4V. This allows proper ON/OFF control of the paper transistor. Apart from that transparent conductive oxides can be also used as cathode/anode materials allowing so the production of thin film batteries with transparent electrodes compatible with flexible, invisible, self powered and wireless electronics. © 2011 SPIE.

Wide band gap microcrystalline silicon films have aroused considerable interest since they combine some electro-optical advantages of amorphous and crystalline materials highly important to produce electro-optical devices such as TFTs and solar cells. In this paper we present results concerning the electro-optical characteristics of highly transparent and conductive n-type μc-Si based films. Here, emphasis is given to the production of n-type μc-films with optical gaps of 2.3 eV and dark conductivity's of 6.5 Scm-1.

This work's aim is to report for the first time the cubic to hexagonal phase transition in tin-doped In2O3 films with a Sn/In atomic ratio of 0.03, fabricated at low temperature and normal pressure from alcoholic solution of InCl3 and SnCl4. The performed X-ray diffraction measurements show a difference between crystallographic symmetry of thin (100 nm) and thick (400 nm) films prepared in the same conditions: the structure of thick films can be related to high pressure In2O3 hexagonal system with a preferred orientation of c-axis parallel to the substrate surface, while thin films present a cubic symmetry with columnar (400) grain orientation. Phase transition nature is connected with non-axial tensile deformation of indium oxide grid due to insertion of chlorine ions in the position of two diagonally opposite oxygen vacancies in In2O3 network.

The current transport in metal-amorphous semiconductor barriers is examined by solving the proper Poisson's equation and transport equations within the semiconductor's space charge region taking into account the role of trap shallow states distribution function. The effect of metal is also included through appropriate boundary conditions of the above solutions. Generalized transport equations will be derived either when thermionic drift-diffusion emission process dominates or when the conduction mechanism is mainly due to drift-diffusion emission. Both situations will be analysed with or without neglecting carriers losses during their collision free path, from which a tractable expression for the current-voltage characteristic will be determined.

The aim of this work is to provide the basis for the interpretation of the steady state lateral photoeffect observed in p-i-n a-Si:H 1D Thin Film Position Sensitive Detectors (1D TFPSD). The experimental data recorded in 1D TFPSD devices with different performances are compared with the predicted curves and the obtained correlation's discussed.

This paper presents results of the spatial and frequency detection limits of an integrated array of 32 one-dimensional amorphous silicon thin film position sensitive detectors with a nip structure, under continuous and pulsed laser operation conditions. The data obtained show that 0.45×0.06 cm arrays, occupying a total active area of about 1 cm2 have a spatial resolution better than 10 μm (modulation transfer function of about 0.2), with a cut-off frequency of about 6.8 KHz. Besides that, under pulsed laser conditions the device non-linearity has its minimum (about 1.6%), for a frequency of about 200Hz. Up to the limits of the cut-off frequency, the device non-linearity increases to values above 4%.

Reported herein is a nonvolatile n-type floating gate memory paper field-effect transistor, emphasizing the role of the paper structure and properties on the device performance recorded such as in the high capacitance per unit area at low frequencies (>2.5 μFcm-2) and so on the set of high charge retention times achieved (>16000 hours). The device was built via the hybrid integration of natural cellulose fibers, which act simultaneously as substrate and gate dielectric, using amorphous indium zinc and gallium indium zinc oxides respectively for the gate electrode and channel layer. This was complemented by the use of continuous patterned metal layers as source/drain electrodes. © 2010 Copyright SPIE - The International Society for Optical Engineering.

We present the modelling of a new two-terminal and low-voltage operating optoelectronic device based on MIS silicon structure with multichannel insulator and having as gate a transparent metallic tin-doped indium oxide (ITO) layer deposited by spray pyrolysis technique over the insulator layer. ITO layer has a multiple non-rectifier electrical contact with silicon substrate, in the SiO2 channel's region. Construction details of the process, together with its operating characteristics are given. The devices developed do not require external active electronic components (transistors, microschemes) to execute their functions and to transform analogue input optical signals to digital output form, highly important for a wide range of optoelectronic applications.

A linear array thin film position sensitive detector (LTFPSD) based on hydrogenated amorphous silicon (a-Si:H) is proposed for the first time, taking advantage of the optical properties presented by a-Si:H devices we have developed a LTFPSD with 128 integrated elements able to be used in 3-D inspections/measurements. Each element consists on a one-dimensional LTFPSD, based on a p.i.n. diode produced in a conventional PECVD system, where the doped layers are coated with thin resistive layers to establish the required device equipotentials. By proper incorporation of the LTFPSD into an optical inspection camera it is possible to acquire information about an object/surface, through the optical cross-section method. The main advantages of this system, when compared with the conventional CCDs, are the low complexity of hardware and software used and that the information can be continuously processed (analogue detection).

In this paper we report the success in fabricating FTO/Si surface-barrier photodiodes produced by spray pyrolysis deposition technique, under ambient conditions. Three types of photodetectors for low-voltage-bias operation were developed based on high-resistivity silicon: 1. X-Ray detectors with energy resolution of 16.5% at 661.5 keV (137Cs source), consisting of surface-barrier PIN photodiode with an active area of 50 mm2 operating at 5 V reverse bias, scintillator based on monocrystalline Bi4Ge3O12 and preamplifier (noise of 250 e- RMS.); 2. Fast-response surface-barrier FTO/n–n+ silicon epitaxial photodiodes, operating at 10 V bias with rise times of 2 ns at λ = 0.85 μm; 3. Radiation-resistant drift epitaxial surface-barrier PIN photodiodes for unbiased operating conditions, with an exponential impurity distribution in a 8 μm thick epitaxial layer. A built-in electrical field due to the carrier concentration distribution in the epitaxial layer provides a considerable improvement in the `critical fluence' value (3×1014 cm-2) for neutron irradiation.

This paper presents the process conditions that lead to the production of nanostructured silicon films grown by plasma enhanced chemical vapour deposition close to the so-called gamma regime (powder formation), highly dense and with low density of bulk states. Thus, the powder management is one important issue to be addressed in this paper. As a general rule we observed that high quality films (low density of states and high μτ products) are obtained when films are grown under low ion bombardment at high hydrogen dilution and deposition pressure conditions, to allow the proper surface passivation and surface activation.

P-type thin-film transistors (TFTs) using room temperature sputtered tin and copper oxide as a transparent oxide semiconductor have been produced on rigid and paper substrates. The SnO x films shows p-type conduction presenting a polycrystalline structure composed with a mixture of tetragonal β-Sn and α-SnO x phases, after annealing at 200°C. These films exhibit a hole carrier concentration in the range of ≈ 10 16-10 18 cm -3, electrical resistivity between 101-102 Ωcm, Hall mobility of 4.8 cm 2/Vs, optical band gap of 2.8 eV and average transmittance ≈ 85 % (400 to 2000 nm). Concerning copper oxide Cu xO thin films they exhibit a polycrystalline structure with a strongest orientation along (111) plane. The Cu xO films produced between an oxygen partial pressure of 9 to 75% showed p-type behavior, as it was measured by Hall effect and Seebeck measurements. The bottom gate p-type SnO x TFTs present field-effect mobility above 1.24 cm 2/Vs (including the paper p-type oxide TFT) and an on/off modulation ratio of 10 3 while the Cu xO TFTs exhibit a field-effect mobility of 1.3×10 -3 cm 2/Vs and an on/off ratio of 2×10 2. © 2012 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

In this paper we report results concerning the use of paper as substrate and as an electronic component for the next generation of sustainable low cost electronic systems, where different examples of applications are given. © 2013 Society for Information Display.

Photocurrent enhancement in thin a-Si:H solar cells due to the plasmonic light trapping is investigated, and correlated with the morphology and the optical properties of the selfassembled silver nanoparticles incorporated in the cells' back reflector. © 2014 Optical Society of America.

Amorphous Silicon solar cells have been produced by a two consecutive decomposition and deposition chamber system, using polished S. S. substrates. Through a systematic investigation of the electrical and optical properties of doped and undoped amorphous silicon layers (1) we observe that the deposition conditions (gas partial pressure, density of r. f. power, substrate temperature, electromagnetic static fields applied to the substrate, and gas flow rate) influence films properties. In the course of this investigation we have been studying the role of the sheet resistance, R//s, of the I. T. O. layer on the short circuit current, I//s//c, and on the open circuit voltage, V//o//c, of p. i. n. structures of 16cm**2 in area. The obtained results indicate that V//o//c is almost independent on R//s, while I//s//c variation approaches a square root dependence on R//s.

The aim of this work is to present an analytical model able to interpret the experimental data of the dependence of film's uniformity on the discharge pressure, gas flow and temperature used during the production of thin films by the plasma enhancement chemical vapour deposition technique, under optimised electrode's geometry and electric field distribution. To do so, the gas flow is considered to be quasi-incompressible and inviscous leading to the establishment of the electro-fluid-mechanics equations able to interpret the film's uniformity over the substrate area, when the discharge process takes place in the low power regime.

The aim of this work is to interpret the role of the lateral leakage current on the a-Si:H solar cell performances (J-V characteristics, responsivity and the apparent device degradation behaviour), under low illumination conditions.

Silicon oxycarbide microcrystallinc layers, n- and p-doped, highly conductive and highly transparent have been produced using a Two Consecutive Decomposition and Deposition Chamber (TCDDC) system. The films exhibit suitable properties for optoelectronic applications where wide band gap materials with required conductivity and stability are needed. In this paper we present the role of partial oxygen pressure (po2) in controlling the composition, structure and transport properties (conductivity. δd and optical gap, Eop) of silicon oxycarbide microcrystalline layers. © 1994 Materials Research Society.

The aim of this work is to provide the basis for the interpretation, under steady state, of the lateral photoeffect in p-i-n a-Si:H 1D Thin Film Position Sensitive Detectors (1D TFPSD) through an analytical model. The experimental data recorded in 1D TFPSD devices with different performances are compared with the predicted curves and the obtained correlation's discussed.

This work reports the structure and electro-optical characteristics of different metal oxide films obtained by spray pyrolysis on heated glass substrates, aiming their application in optoelectronic devices. The results show that this technique leads to thin films with properties ranging from dielectric to degenerate semiconductors, offering the following advantages: simplicity, low cost, high productivity and the possibility of covering large areas, highly important for large area device applications.

This work presents experimental data concerning the role of the oxygen partial pressure used during the preparation process, on the structure, composition and optoelectronic properties of wide band gap doped microcrystalline silicon oxycarbide films produced by a TCDDC system [1].

Tin doped indium oxide (ITO) films were deposited on glass substrates by rf reactive magnetron sputtering using a metallic alloy target (In-Sn, 90-10). The post-deposition annealing has been done for ITO films in air and the effect of annealing temperature on the electrical, optical and structural properties of ITO films was studied. It has been found that the increase of the annealing temperature will improve the film electrical properties. The resistivity of as-deposited film is about 1.3×10-1 Ω* cm and decreases down to 6.9×10-3 Ω* cm as the annealing temperature is increased up to 500°C. In addition, the annealing will also increase the film surface roughness which can improve the efficiency of amorphous silicon solar cells by increasing the amount of light trapping.

This paper presents results of the role of the oxygen partial pressure (pO2) used on the properties exhibited by doped μc silicon oxycarbide films produced by a Two Consecutive Decomposition and Deposition Chamber (TCDDC) system [1], where a spatial separation between the plasma and the growth regions is achieved. The films produced are highly conductive and transparent with suitable properties for optoelectronic applications.

This paper discusses the effect of order and disorder on the electrical and optical performance of ionic oxide semiconductors based on zinc oxide. These materials are used as active thin films in electronic devices such as pn heterojunction solar cells and thin-film transistors. Considering the expected conduction mechanism in ordered and disordered semiconductors the role of the spherical symmetry of the s electron conduction bands will be analyzed and compared to covalent semiconductors. The obtained results show p-type c-Si/a-IZO/poly-ZGO solar cells exhibiting efficiencies above 14% in device areas of about 2.34 cm2. Amorphous oxide TFTs based on the Ga-Zn-Sn-0 system demonstrate superior performance than the polycrystalline TFTs based on ZnO, translated by ION/IOFF ratio exceeding 107, turn-on voltage below 1-2 V and saturation mobility above 25 cm2/Vs. Apart from that, preliminary data on p-type oxide TFT based on the Zn-Cu-O system will also be presented. © 2009 SPIE.