Rodrigo Martins

Today there is a strong interest in the scientific and industrial community concerning the use of biopolymers for electronic applications, driven mainly by low-cost and disposable applications. Adding to this interest, we must recognise the importance of the dream of wireless auto-sustained and low-energy-consumption electronics. This dream can be fulfilled by cellulose paper, the lightest and the cheapest known substrate material, as well as the Earth's major biopolymer and of tremendous global economic importance. Most of the paper used up to now is optimised in terms of the required mechanical and physical properties to be used as the support of inks of different origins. In the future, specific electronic heterogeneous paper sheets should be fabricated aiming to get paper fibers with required bulk and surface functionalities, proper water/vapour barrier, size and diameter/thickness of the fibrils and full paper thickness. This will be the function of components/devices to be incorporated/integrated such as thin-film transistors, complementary metal oxide semiconductor devices, passive electronic components (resistances, inductors and capacitors), memory transistors, electrochromics and thin-film paper batteries. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Where a-Si:H pin devices are concerned, one of the main obstacles regarding improved performance is device stability, usually attributed to adverse behaviour at various interfaces within the device. Several attempts have been made to overcome this problem, such as the use of blocking layers at the interfaces. Although these have led to some improvements in device performance, most of the problems associated with device stability remain. This is mainly due to the defects at the interfaces, since the blocking layers (silicon alloys with carbon, nitrogen or oxygen) usually have a high density of bulk states, in comparison to intrinsic a-Si:H films. In this paper, we present a method that seems to be capable of improving device stability. It consists of performing a controlled removal of oxide interlayers at the interfaces, by an appropriate etching process. This enables the production of highly smoothed interfaces, and reduces possible cross-contamination of the i-layer from the adjacent doped layers. This amounts to a new design of typical pin devices, in which thin absorber layers are placed at the p/i and i/n interfaces. Their purpose is to trap most of the impurity atoms diffused from the doped layers, after which they are removed by appropriate etching. The fabrication of the absorbers (sacrificial layers), the nature of the etching and the tailoring of the defect profile at the interfaces will be discussed, including the performance exhibited by the resulting devices. © 2002 Elsevier Science B.V. All rights reserved.

One of the main problems in producing large area amorphous silicon devices concerns films uniformity. In this paper we present data concerning the role of reactor geometry and design and on the film performances as well as the problems related to mechanical mismatches in scaling up the reactor size. © 1991 Elsevier Science Publishers B.V. All rights reserved.

This paper deals with the engineering aspects related to the rf energy coupling in Plasma Enhanced Chemical Vapour Deposition (PECVD) processes, in a diode-type unit in which an extra grid is used. The main emphasis is given in the determination of the real power delivered to the gas and comparing it with the total power losses, besides determining the best way to control the powder formed during the process. © 1994.

Reported herein is a nonvolatile n-type floating gate memory paper field-effect transistor, emphasizing the role of the paper structure and properties on the device performance recorded such as in the high capacitance per unit area at low frequencies (>2.5 μFcm-2) and so on the set of high charge retention times achieved (>16000 hours). The device was built via the hybrid integration of natural cellulose fibers, which act simultaneously as substrate and gate dielectric, using amorphous indium zinc and gallium indium zinc oxides respectively for the gate electrode and channel layer. This was complemented by the use of continuous patterned metal layers as source/drain electrodes. © 2010 Copyright SPIE - The International Society for Optical Engineering.

The special Professor Walter E. Spear commemoration issue of the Philosophical Magazine, published in October 2009, contains papers which cover the numerous relevant issues, driven by commercial applications, primarily solar energy and displays. Kocka reviews the complex microstructure of crystallites embedded in the amorphous silicon tissue, the transport mechanism is determined by the conductive grains and influenced by the passivation through H at the grain boundaries. Hugger and co-researchers report on transient photocapacitance spectroscopy and drive-level capacitance profiling as a way of elucidating the fundamental electronic properties of hydrogenated ncSi. Tawada recounts the history of a-Si:H pin heterojunction solar cells, emphasizing the role of the p-type silicon carbide layer in the improvement of the device. Schubert and colleagues focus their work on the production of flexible PV modules with many applications in the architectural arena or integrated into clothing.

The model presented is based on the heat transfer and energy balance equations that rule the set of physical and chemical interactions that take place on the gas phase of a growth process, assuming that the deposition process occurs under laminar dynamic flow conditions (Knudsen number below 1). In these conditions, the chemistry and physics of the process involved in the growth mechanism of silicon thin films produced by the hot wire or the hot-wire plasma assisted technique can be proper derived by balance equations that supply information about how the plasma density, the gas dilution and the gas temperature influence the growth mechanism and the equilibrium of the concentration of species presented on the growth surface. The model developed establishes a relation between the abundance species formed and the parameters initiators of the process such as the filament temperature and the rf power density used.

The aim of this paper is to present data on the dependence of the electro-optical characteristics and structure of n-type microcrystalline silicon films on the r.f. power used during the deposition of films produced by the plasma-enhanced chemical vapour deposition technique. The interest of these films arise from the fact that they combine some electro-optical advantages of amorphous (wide optical gap) and crystalline materials (electronic behaviour), highly interesting in the production of a wide variety of optoelectronic devices such as solar cells and thin film transistors. In this paper, microcrystalline n-type films presenting simultaneously optical gaps of about 2.3 eV, dark conductivity of 6.5 S cm-1 and Hall mobility of about 0.86 cm2 V-1 s-1 will be reported, the highest combined values for n-type microcrystalline silicon films, as far as we know. © 1997 Elsevier Science S.A.

This paper describes a novel colorimetric method for detection of nucleic acid targets in a homogeneous format with improved sensitivity by means of a system based on the combination of a tunable monochromatic light source and an amorphous/nanocrystalline silicon photodetector that detects color and light intensity changes undergone by samples/assays containing tailored gold nanoparticles probes. This new low cost, portable, fast and simple optoelectronic platform, with the possibility to be re-used, permits detection of at least 400 fentomole of specific DNA sequences without target or signal amplification and was applied to the rapid detection of human pathogens in large variety of clinical samples such as Mycobacterium tuberculosis. © 2008 Elsevier B.V. All rights reserved.

This paper deals with a new design method for the interfaces of a-Si:H pin solar cells that improves the stability and performances of devices deposited in a single batch chamber process. The method consists in removing a deposited sacrificial layer placed between the p/i and/or i/n interfaces by etching. This layer is an absorber of defects and impurities that are introduced in the interfaces, mainly from the chamber walls cross-contamination and the substrate surface. The results achieved increase the device fill factor and short circuit current density, respectively towards 75% and 16.3 mA cm-2, with a final efficiency of about 10%, before light soaking experiments. © 2000 Elsevier Science B.V. All rights reserved.

This work aims to report results of the spatial and frequency optical detection limits of integrated arrays of 32 one-dimensional amorphous silicon thin film position sensitive detectors with nip or MIS structure, under continuous and pulsed laser operation conditions. The arrays occupy a total active area of 45 mm2 and have a plane image resolution better than 15 μm with a cut-off frequency of about 6.8 kHz. The non-linearity of the array components varies with the frequency, being about 1.6% for 200 Hz and about 4% for the cut-off frequency (6.8 kHz).

This paper deals with the interpretation of transport properties of amorphous silicon hydrogenated films (a-Si:H) through dark conductivity, photoconductivity and pulse controlled capacitance-voltage measurements. a-Si:H films were produced by rf glow discharge coupled either inductively or capacitively to a 3% SiH4/Ar mixture at different crossed electromagnetic static fields. The data concerned with the dark activation energy, photoactivation energy, variation of the density of localized states and photosensitivity, (σph/σd)25°C, of a-Si:H films can account for their optoelectronic properties which are strongly dependent on the deposition parameters. We also observed that crossed electromagnetic static fields applied during film formation influences hydrogen incorporation in a different manner than previously proposed. © 1983.

In this work, we present a model to interpret the steady-state and the dynamic detection limits of 1-D Thin Film Position Sensitive Detectors (1-D TFPSD) based on p-i-n a-Si:H devices. From this, an equivalent electric circuit is derived and the predicted values are compared with the experimental results obtained in 1-D TFPSD devices, with different sizes. The model is also able to determine the device characteristics that influence the spatial limits and the response time of the device. © 1996 IEEE.

We have deposited by Plasma Enhanced Chemical Vapour Deposition phosphorus doped amorphous and microcrystalline silicon films, as a function of the RF power (10-300 W), using a PH3/(SiH4 + H2 + He)mixture. It was found that films microcrystallization occurs for powers above 130 W, where a clear phase transition occurs. The microcrystalline films produced present high dark conductivities and optical band gaps, where the crystalline volume fraction is above 25%, as revealed by micro Raman spectroscopy. The Hall mobility have been also determined for amorphous and microcrystalline films, as a function of temperature, in the range 280-340 K. The data show that for the microcrystalline films the conduction is mainly in the extended states of the microcrystals, confirming also the double sign anomaly. That is, for n-type films, the sign is positive for the amorphous case while it is negative for the microcrystalline case. © 1998 Elsevier Science S.A.

The objective of this work is to provide a basis for the interpretation of the a-Si:H photodiode behaviour under low illumination level conditions, where a lateral leakage current plays an important role on the devices' performances when the doped collecting layer can not be considered a true equipotential. To determine this effect, a-Si:H p.i.n devices with small metal dot contacts, matrix distributed, were produced and analysed before and after etching the surrounding doped region of the metal collecting contact. The experimental data fit a model that includes the contribution of a lateral leakage current influencing the J-V characteristics, responsivity and the apparent light degradation behaviour of the device.

The aim of this work is to provide the basis for the interpretation, under steady state conditions, of the lateral photoeffect in p-i-n a-Si:H one-dimensional thin-film position-sensitive detectors (1D TFPSD) and the determination of its linear spatial detection limits, function of the device, and light spot source characteristics. This leads to the development of a model, based on the application of the Poisson, continuity, and current density equations in the p-i-n junction, where two thin resistive layers, as equipotentials, are considered on both sides of the doped layers. The experimental data recorded in 1D TFPSD devices with different performances are compared with the predicted curves and the obtained correlations discussed. © 1995 American Institute of Physics.

We present the modelling of a new two-terminal and low-voltage operating optoelectronic device based on MIS silicon structure with multichannel insulator and having as gate a transparent metallic tin-doped indium oxide (ITO) layer deposited by spray pyrolysis technique over the insulator layer. ITO layer has a multiple non-rectifier electrical contact with silicon substrate, in the SiO2 channel's region. Construction details of the process, together with its operating characteristics are given. The devices developed do not require external active electronic components (transistors, microschemes) to execute their functions and to transform analogue input optical signals to digital output form, highly important for a wide range of optoelectronic applications.

A linear array thin film position sensitive detector (LTFPSD) based on hydrogenated amorphous silicon (a-Si:H) is proposed for the first time. Taking advantage of the optical properties presented by a-Si:H devices, we have developed a LTFPSD with 128 integrated elements able to be used in 3D inspections/measurements. Each element consists of a one-dimensional LTFPSD, based on a p-i-n diode produced in a conventional PECVD system, where the doped layers are coated with thin resistive layers to establish the required device equipotentials. By proper incorporation of the LTFPSD into an optical inspection camera it will be possible to acquire information about an object/surface, through the optical cross-section method. The main advantages of this system, when compared with the conventional CCDs, are the low complexity of hardware and software used and that the information can be continuously processed (analog detection). © 1995 American Institute of Physics.

A linear array thin film position sensitive detector (LTFPSD) based on hydrogenated amorphous silicon (a-Si:H) is proposed for the first time, taking advantage of the optical properties presented by a-Si:H devices we have developed a LTFPSD with 128 integrated elements able to be used in 3-D inspections/measurements. Each element consists on a one-dimensional LTFPSD, based on a p.i.n. diode produced in a conventional PECVD system, where the doped layers are coated with thin resistive layers to establish the required device equipotentials. By proper incorporation of the LTFPSD into an optical inspection camera it is possible to acquire information about an object/surface, through the optical cross-section method. The main advantages of this system, when compared with the conventional CCDs, are the low complexity of hardware and software used and that the information can be continuously processed (analogue detection).

In this paper we report the success in fabricating FTO/Si surface-barrier photodiodes produced by spray pyrolysis deposition technique, under ambient conditions. Three types of photodetectors for low-voltage-bias operation were developed based on high-resistivity silicon: 1. X-Ray detectors with energy resolution of 16.5% at 661.5 keV (137Cs source), consisting of surface-barrier PIN photodiode with an active area of 50 mm2 operating at 5 V reverse bias, scintillator based on monocrystalline Bi4Ge3O12 and preamplifier (noise of 250 e- RMS.); 2. Fast-response surface-barrier FTO/n–n+ silicon epitaxial photodiodes, operating at 10 V bias with rise times of 2 ns at λ = 0.85 μm; 3. Radiation-resistant drift epitaxial surface-barrier PIN photodiodes for unbiased operating conditions, with an exponential impurity distribution in a 8 μm thick epitaxial layer. A built-in electrical field due to the carrier concentration distribution in the epitaxial layer provides a considerable improvement in the `critical fluence' value (3×1014 cm-2) for neutron irradiation.

We report the properties and optoelectronic applications of transparent and conductive indium and tin oxide films prepared by the spray pyrolysis method and doped with Sn or F, respectively. The film properties have been measured using X-ray diffraction, optical and electrical absorption. As examples of applications we produced a set of selective optical detectors for different spectral regions, covering the wavelength range from 0.25 to 1.1 μm, based on metal oxide-semiconductor heterostructures and using different substrates such as: GaP, GaSe, AlxGa1-xAs, GaAs and Si. The fabricated devices exhibit several features such as: production simplicity, high quantum efficiency, uniform sensitivity over the entire active area and a high response speed. Finally, we present a high quantum efficiency and solar blind monocrystalline zinc sulphide optical sensor fabricated by spray deposition as an alternative to the ultraviolet-enhanced SiC and GaN photodetectors and the performances of a solar cell. © 1998 Elsevier Science B.V. All rights reserved.

This paper reports the performance of small area solar cells, 128 linear integrated position sensitive detector arrays and thin film transistors based on nanostructured silicon thin films produced by plasma-enhanced chemical vapour deposition technique, close to the onset of dusty plasma conditions, within the transition region from amorphous to microcrystalline. The small area solar cells, produced in a modified single chamber reactor, exhibited very good electrical characteristics with a conversion efficiency exceeding 9%. The 128 integrated position sensitive detector arrays, based on a similar pin structure, allow real-time 3D object imaging with a resolution higher than 90 l p/mm. The thin film transistors produced exhibited field effect mobility of 2.47 cm 2/V/s, threshold voltage of 2 V, on/off ratio larger than 10 7 and sub-threshold slopes of 0.32 V/decade, which are amongst the best results reported for this type of device. © 2009 Taylor & Francis.

This paper presents the process conditions that lead to the production of nanostructured silicon films grown by plasma enhanced chemical vapour deposition close to the so-called gamma regime (powder formation), highly dense and with low density of bulk states. Thus, the powder management is one important issue to be addressed in this paper. As a general rule we observed that high quality films (low density of states and high μτ products) are obtained when films are grown under low ion bombardment at high hydrogen dilution and deposition pressure conditions, to allow the proper surface passivation and surface activation.