Rodrigo Martins

This paper presents the characterization of fundamental analog and digital circuits with a-IGZO TFTs from measurements performed at normal ambient. The fundamental blocks considered in this work include digital logic gates, a low-power single stage high-gain amplifier with capcacitive bootstrapping and a level shifter/buffer. These circuits are important functional blocks in analog/Mixed signal IC design with oxide TFTs. Being fabricated at low temperature (< 200 °C), they can find potential applications in low-cost large-area flexible systems. © 2016 IEEE.

This paper presents a study concerning the role of channel length scaling on IGZO TFT technology benchmark parameters, which are fabricated at temperatures not exceeding 180\, ^{\circ}C. The parameters under investigation are unity current-gain cutoff frequency, intrinsic voltage-gain, and on-resistance of the bottom-gate IGZO TFTs. As the channel length varies from 160 to 3 μm, the measured cutoff frequency increases from 163 {\rm kHz} to 111.5 {\rm MHz}, which is a superior value compared to the other competing low-temperature thin-film technologies, such as organic TFTs. On the other hand, for the same transistor dimensions, the measured intrinsic voltage-gain is changing from 165 to 5.3 and the on-resistance is decreasing from 1135.6 to 26.1 kØmega. TFTs with smaller channel length (3 μ m) have shown a highly negative turn-on voltage and hump in the subthreshold region, which can be attributed to short channel effects. The results obtained here, together with their interpretation based on device physics, provide crucial information for accurate IC design, enabling an adequate selection of device dimensions to maximize the performance of different circuit building blocks assuring the multifunctionality demanded by system-on-panel concepts. © 2005-2012 IEEE.

This letter presents a novel high-gain four-quadrant analog multiplier using only n-type enhancement indium- gallium-zinc-oxide thin-film-transistors. The proposed circuit improves the gain by using an active load with positive feedback. A Gilbert cell with a diode-connected load is also presented for comparison purposes. Both circuits were fabricated on glass at low temperature (200 °C) and were successfully characterized at room temperature under normal ambient conditions, with a power supply of 15 V and 4-pF capacitive load. The novel circuit has shown a gain improvement of 7.2 dB over the Gilbert cell with the diode-connected load. Static linearity response, total harmonic distortion, frequency response, and power consumption are reported. This circuit is an important signal processing building block in large-area sensing and readout systems, specially if data communication is involved. © 2016 IEEE.

The aim of presented work is to show the improvements obtained in the properties of TiO2 films for dye sensitized solar cells fabricated by inkjet printing using an innovative methodology. We describe the development and properties of TiO2-based inks used in a lab-scale printer, testing various commercial TiO2 pastes. The porosity of the deposited inkjet printed TiO2 films is much higher than using the conventional "doctor blade" deposition technique, as the ink solvent evaporates during the droplet fly from the nozzle to the substrate due to its picoliter volume and the applied heating of a printing stage (70°C). Thanks to higher surface area, the dye sensitized solar cells incorporating inkjet printed TiO2 film gave higher efficiencies (ηmax≈3.06%) than the more compact films obtained by the "doctor blade" method (ηmax≈2.56%). Furthermore, electrochemical analysis indicates that for whole tested thickness range, the inkjet printed layers have higher effective electron diffusion length indicating their better transport properties. © 2015 Elsevier Inc..

A novel linear analog adder is proposed only with n-type enhancement IGZO TFTs that computes summation of four voltage signals. However, this design can be easily extended to perform summation of higher number of signals, just by adding a single TFT for each additional signal in the input block. The circuit needs few number of transistors, only a single power supply irrespective of the number of voltage signals to be added, and offers good accuracy over a reasonable range of input values. The circuit was fabricated on glass substrate with the annealing temperature not exceeding 200° C. The circuit performance is characterized from measurements under normal ambient at room temperature, with a power supply voltage of 12 V and a load of ≈ 4 pF. The designed circuit has shown a linearity error of 2.3% (until input signal peak to peak value is 2 V), a power consumption of 78 μW and a bandwidth of ≈ 115 kHz, under the worst case condition (when it is adding four signals with the same frequency). In this test setup, it has been noticed that the second harmonic is 32 dB below the fundamental frequency component. This circuit could offer an economic alternative to the conventional approaches, being an important contribution to increase the functionality of large area flexible electronics. © 2016 IEEE.

The degradation of thin-film transistors (TFTs) caused by the self-heating effect constitutes a problem to be solved for the next generation of displays. Aluminum nitride (AlN) is a viable alternative for gate dielectric of TFTs due to its good thermal conductivity, matching coefficient of thermal expansion to indium-gallium-zinc-oxide, and excellent stability at high temperatures. Here, AlN thin films of different thicknesses were fabricated by a low temperature reactive radio-frequency magnetron sputtering process, using a low cost, metallic Al target. Their electrical properties have been thoroughly assessed. Furthermore, the 200 nm and 500 nm thick AlN layers have been integrated as gate-dielectric in transparent TFTs with indium-gallium-zinc-oxide as channel semiconductor. Our study emphasizes the potential of AlN thin films for transparent electronics, whilst the functionality of the fabricated field-effect transistors is explored and discussed. © 2016 Elsevier B.V. All rights reserved.

Development time and accuracy are measures that need to be taken into account when devising device models for a new technology. If complex circuits need to be designed immediately, then it is very important to reduce the time taken to realize the model. Solely based on data measurements, artificial neural networks (ANNs) modeling methodologies are capable of capturing small and large signal behavior of the transistor, with good accuracy, thus becoming excellent alternatives to more strenuous modeling approaches, such as physical and semi-empirical. This paper then addresses a static modeling methodology for amorphous Gallium-Indium-Zinc-Oxide - Thin Film Transistor (a-GIZO TFT), with different ANNs, namely: multilayer perceptron (MLP), radial basis functions (RBF) and least squares-support vector machine (LS-SVM). The modeling performance is validated by comparing the model outcome with measured data extracted from a real device. In case of a single transistor modeling and under the same training conditions, all the ANN approaches revealed a very good level of accuracy for large- and small-signal parameters (gm and gd), both in linear and saturation regions. However, in comparison to RBF and LS-SVM, the MLP achieves a very acceptable degree of accuracy with lesser complexity. The impact on simulation time is strongly related with model complexity, revealing that MLP is the most suitable approach for circuit simulations among the three ANNs. Accordingly, MLP is then extended for multiple TFTs with different aspect ratios and the network implemented in Verilog-A to be used with electric simulators. Further, a simple circuit (inverter) is simulated from the developed model and then the simulation outcome is validated with the fabricated circuit response. © 2014 Elsevier Ltd . All rights reserved.

This paper presents analog building blocks that find potential applications in display panels. A buffer (source-follower), subtractor, adder, and high-gain amplifier, employing only n-type enhancement amorphous gallium-indium-zinc-oxide thin-film transistors (a-GIZO TFTs), were designed, simulated, fabricated, and characterized. Circuit simulations were carried out using a neural model developed in-house from the measured characteristics of the transistors. The adder-subtractor circuit presents a power consumption of 0.26 mW, and the amplifier presents a gain of 34 dB and a power consumption of 0.576 mW, with a load of 10 MΩ16 pF. To the authors' knowledge, this is the highest gain reported so far for a single-stage amplifier with a-GIZO TFT technology. © 2015 IEEE.

The influence of Ag nanoparticles (Ag NPs) on the luminescence of electrospun nonwoven mats made of polyvinylpyrrolidone (PVP) has been studied in this work. The PVP fibers incorporating 2.1-4.3 nm size Ag NPs show a significant photoluminescence (PL) band between 580 and 640 nm under 325 nm laser excitation. The down conversion luminescence emission is present even after several hours of laser excitation, which denotes the durability and stability of fibers to consecutive excitations. As so these one-dimensional photonic fibers made using cheap methods is of great importance for organic optoelectronic applications, fluorescent clothing or counterfeiting labels. © 2014 Elsevier B.V. All rights reserved.

Solution based deposition has been recently considered as a viable option for low-cost flexible electronics. In this context research efforts have been increasingly centred on the development of suitable solution-processed materials for oxide based transistors. Nevertheless, the majority of synthetic routes reported require the use of toxic organic solvents. In this work we report on a new environmental friendly solution combustion synthesis route, using ethanol as solvent, for the preparation of indium/gallium free amorphous zinc-tin oxide (ZTO) thin film transistors (TFTs) including AlOx gate dielectric. The decomposition of ZTO and AlOx precursor solutions, electrical characterization and stability of solution processed ZTO/AlOx TFTs under gate-bias stress, in both air and vacuum atmosphere, were investigated. The devices demonstrated low hysteresis (ΔV=0.23 V), close to zero turn on voltage, low threshold voltage (VT=0.36 V) and a saturation mobility of 0.8 cm2 V-1 s-1 at low operation voltages. Ethanol based ZTO/AlOx TFTs are a promising alternative for applications in disposable, low cost and environmental friendly electronics. © 2015 IOP Publishing Ltd.

This paper analyzes transparent two-TFT current mirrors using a-GIZO TFTs with different mirroring ratios. In order to achieve a high mirroring ratio, the output TFT in the circuit employed a fingered structure layout to minimize area and overlap capacitance. The analysis of the current mirrors is performed in three phases. In the first, a radial basis function based (RBF) model is developed using measured data from fabricated TFTs on the same chip. Then, in the second phase, the RBF model is implemented in Verilog-A that is used to simulate two-TFT current mirrors with different mirroring ratios. The simulations are carried out using Cadence spectre simulator. In the third phase, simulation results are validated with the measured response from the fabricated circuits. © 2014 IEEE.

We have projected and fabricated a microfluidic platform for DNA sensing that makes use of an optical colorimetric detection method based on gold nanoparticles. The platform was fabricated using replica moulding technology in PDMS patterned by high-aspect-ratio SU-8 moulds. Biochips of various geometries were tested and evaluated in order to find out the most efficient architecture, and the rational for design, microfabrication and detection performance is presented. The best biochip configuration has been successfully applied to the DNA detection of Mycobacterium tuberculosis using only 3. l on DNA solution (i.e. 90. ng of target DNA), therefore a 20-fold reduction of reagents volume is obtained when compared with the actual state of the art. © 2013 Elsevier B.V.

A high-gain amplifier topology, with all single n-type enhancement transistors, is proposed in this paper. This type of circuits are essential in transparent TFT technologies, such as GIZO and ZnO that lack complementary type transistor. All circuits were simulated using BSIM3V3 model of a 0.35 μm CMOS technology, due to the absence of a complete electrical model for the TFTs. Results reveal that the proposed circuit promise more gain, lower power consumption and higher bandwidth than the existing solutions under identical bias conditions. © 2013 IEEE.

Transparent TFT technologies, with amorphous semiconductor oxides are lacking a complementary type transistor. This represents a real challenge, when the design of high-gain amplifiers are considered, without resorting to passive resistive elements. However, some solutions do exist to overcome the lack of a p-type transistor. This paper then presents a comparison analysis of two high-gain single-stage amplifier topologies using only n-type enhancement transistors. In these circuits, high gain is achieved using positive feedback for the load impedance. The comparison is carried out in terms of bandwidth, power consumption and complexity under identical bias conditions. Further, the same load impedance is used to develop a novel high-gain multiplier. All the circuits are simulated using a 0.35 μm CMOS technology, as it is easy to test the reliability of the methods, since CMOS transistors have trustworthy models. © 2013 IEEE.

The effect of post-deposition annealing temperature on the pH sensitivity of room temperature RF sputtered +{\hbox{Ta}}-{2}{\hbox{O}}5 was investigated. Structural and morphological features of these films were analyzed before and after annealing at various temperatures. The deposited films are amorphous up to 600 +^{\circ}{\hbox{C}}+ and crystallize at 700 +^{\circ}{\hbox{C}}+ in an orthorhombic phase. Electrolyte-insulator- semiconductor (EIS) field effect based sensors with an amorphous +{\hbox{Ta}}-{2}{\hbox{O}}5 sensing layer showed pH sensitivity above 50 mV/pH. For sensors annealed above 200 +^{\circ}{\hbox{C}}+ pH sensitivity decreased with increasing temperature. Stabilized sensor response and maximum pH sensitivity was achieved after low temperature annealing at 200 +^{\circ}{\hbox{C}}+ , which is compatible with the use of polymeric substrates and application as sensitive layer in oxides TFT-based sensors. © 2005-2012 IEEE.

This paper characterizes transparent current mirrors with n-type amorphous gallium-indium-zinc-oxide (a-GIZO) thin-film transistors (TFTs). Two-TFT current mirrors with different mirroring ratios and a cascode topology are considered. A neural model is developed based on the measured data of the TFTs and is implemented in Verilog-A; then it is used to simulate the circuits with Cadence Virtuoso Spectre simulator. The simulation outcomes are validated with the fabricated circuit response. These results show that the neural network can model TFT accurately, as well as the current mirroring ability of the TFTs. © 2005-2012 IEEE.

This paper addresses a modeling and simulation methodology for analog circuit design with amorphous-GIZO thin-film transistors (TFTs). To reach an effective circuit design flow, with commercially available tools, a TFT model has been first developed with an artificial neural network (ANN). Multilayer perceptron with backpropagation algorithm has been adopted to model the static behavior of the TFT devices, for different aspect ratios. The model was then implemented in Verilog-A, to allow a quick instantiation in circuit. Simulations using Cadence Spectre are performed to validate the model. On a second phase, simulation results of basic analog circuits, with this ANN model, are verified against the actual functional results, namely an adder, subtractor, and current mirror circuit. Results demonstrate not only the ANN model accuracy and compatibility with dc and transient analysis, but also show the a-GIZO TFT capability to perform analog operations. © 2012 IEEE.

This paper presents the results of a preliminary study to examine the ability of post-silicon devices for analog processing. It is focused on the latest thin-film transistors (TFTs) with amorphous gallium-indium-zinc oxide (a-GIZO) as active layer. Three circuit configurations are presented: a differential pair and two multiplier topologies. Both triode and saturation regions of operation are included in the analysis, with the devices set to remain in strong accumulation. A neural model, which is developed based on the measured data of the TFTs, is used for the circuit simulations in the Cadence Virtuoso environment. The analog multipliers simulation results are compared against the expected functional results. © 2012 IEEE.

This chapter gives an overview about GIZO TFTs, comprising an introductory section about generic TFT structure and operation, different semiconductor technologies for TFTs - with special emphasis on AOSs and particularly on GIZO - and then some experimental results obtained for GIZO TFTs fabricated in CENIMAT. Thin-film transistors (TFTs) are important electronic devices which are predominantly used as On/Off switches in active matrix backplanes of flat panel displays (FPDs), namely liquid crystal displays (LCDs) and organic light emitting device (OLED) displays. Even if a-Si:H is still dominating the TFT market in terms of semiconductor technology, oxide semiconductors are emerging as one of the most promising alternatives for the next generation of TFTs, bringing the possibility of having fully transparent devices, low processing temperature, low cost, high performance and electrically stable properties [1, 2]. Amorphous oxide semiconductors (AOS) such as Gallium-Indium-Zinc oxide (GIZO) [3, 4], even if fabricated at temperatures below 150°, are currently capable of providing transistors with field-effect mobility (μFE) exceeding 20 cm2V-1 s-1, threshold voltage (VT) close to 0V, On/Off ratios above 108, subthreshold swing (S) around 0:20V dec-1 and fully recoverable VT shift (ΔVT) lower than 0.5V after 24 h stress with constant drain current of 10 μA. © Springer-Verlag Berlin Heidelberg 2012.

Transparent electronics is emerging as one of the most promising technologies for the next generation of electronic products, away from the traditional silicon technology. It is essential for touch display panels, solar cells, LEDs and antistatic coatings. The book describes the concept of transparent electronics, passive and active oxide semiconductors, multicomponent dielectrics and their importance for a new era of novel electronic materials and products. This is followed by a short history of transistors, and how oxides have revolutionized this field. It concludes with a glance at low-cost, disposable and lightweight devices for the next generation of ergonomic and functional discrete devices. Chapters cover: Properties and applications of n-type oxide semiconductors P-type conductors and semiconductors, including copper oxide and tin monoxide Low-temperature processed dielectrics n and p-type thin film transistors (TFTs) - structure, physics and brief history Paper electronics - Paper transistors, paper memories and paper batteries Applications of oxide TFTs - transparent circuits, active matrices for displays and biosensors Written by a team of renowned world experts, Transparent Oxide Electronics: From Materials to Devices gives an overview of the world of transparent electronics, and showcases groundbreaking work on paper transistors. © 2012 John Wiley & Sons, Ltd.

We present a new approach for real-time monitoring of PCR amplification of a specific sequence from the human c-MYC proto-oncogene using a Ta 2O 5 electrolyte-insulator-semiconductor (EIS) sensor. The response of the fabricated EIS sensor to cycle DNA amplification was evaluated and compared to standard SYBR-green fluorescence incorporation, showing it was possible to detect DNA concentration variations with 30mV/μM sensitivity. The sensor's response was then optimized to follow in real-time the PCR amplification of c-MYC sequence from a genomic DNA sample attaining an amplification profile comparable to that of a standard real-time PCR. Owing to the small size, ease of fabrication and low-cost, the developed Ta 2O 5 sensor may be incorporated onto a microfluidic device and then used for real-time PCR. Our approach may circumvent the practical and economical obstacles posed by current platforms that require an external fluorescence detector difficult to miniaturize and incorporate into a lab-on-chip system. © 2011 Elsevier B.V.

The present work proposes the development of a bio-battery composed by an ultrathin monolithic structure of an electrospun cellulose acetate membrane, over which was deposited metallic thin film electrodes by thermal evaporation on both surfaces. The electrochemical characterization of the bio-batteries was performed under simulated body fluids like sweat and blood plasma [salt solution - 0.9% (w/w) NaCl]. Reversible electrochemical reactions were detected through the cellulose acetate structure. Thus, a stable electrochemical behavior was achieved for a bio-battery with silver and aluminum thin films as electrodes. This device exhibits the ability to supply a power density higher than 3μWcm-2.Finally, a bio-battery prototype was tested on a sweated skin, demonstrating the potential of applicability of this bio-device as a micropower source. © 2010 Elsevier B.V.

A dye sensitized TiO2 photodetector has been integrated with a DNA detection method based on non-cross-linking hybridization of DNA-functionalized gold nanoparticles, resulting in a disposable colorimetric biosensor. We present a new approach for the fabrication of dye sensitized TiO2 photodetectors by an inkjet printing technique-a non-contact digital, additive, no mask and no vacuum patterning method, ideal for cost efficient mass production. The developed biosensor was compared against a dye sensitized photodetector fabricated by the traditional "doctor blade" method. Detection of gold nanoparticle aggregation was possible for concentrations as low as 1.0 nM for the "doctor blade" system, and 1.5 nM for the inkjet printed photodetector. The demonstrated sensitivity limits of developed biosensors are comparable to those of spectrophotometric techniques (1.0 nM). Our results show that a difference higher than 17% by traditional photodetector and 6% by inkjet printed in the photoresponses for the complementary and non-complementary gold nanoprobe assays could be attained for a specific DNA sequence from Mycobacterium tuberculosis, the etiologic agent of human tuberculosis. The decrease of costs associated with molecular diagnostic provided by a platform such as the one presented here may prove of paramount importance in developing countries. © 2009 Elsevier B.V. All rights reserved.

This paper discusses the properties of sputtered multicomponent amorphous dielectrics based on mixtures of high-κ and high-bandgap materials and their integration in oxide TFTs, with processing temperatures not exceeding 1 50° C. Even if Ta2O5 films are already amorphous, multicomponent materials such as Ta2O5-SiO2 and Ta2O5-Al2O3 allow an increase in the bandgap and the smoothness of the films, reducing their leakage current and improving (in the case of Ta2O5-SiO2)the dielectric/semiconductor interface properties when these dielectrics are integrated in TFTs. For HfO2- based dielectrics, the advantages of multicomponent materials are even clearer: while HfO2 films present a polycrystalline structure and a rough surface, HfO2-SiO2 films exhibit an amorphous structure and a very smooth surface. The integration of the multicomponent dielectrics in GIZO TFTs allows remarkable performance, comparable with that of GIZO TFTs using SiO2 deposited at 400°C by PECVD. For instance, with Ta2O5-SiO2 as the dielectric layer, field-effect mobility of 35 cm2/(V-sec), close to 0 V turn-on voltage, an on/off ratio higher than 106, a subthreshold slope of 0.24 V/dec, and a small/recoverable threshold voltage shifts under constant current (ID = 10 μ,A) stress during 24 hours are achieved. Initial results with multilayers of SiO2/HfO 2-SiO2/SiO2 are also shown, allowing a lower leakage current with lower thickness and excellent device performance. © Copyright 2010 Society for Information Display.