Rodrigo Martins

Long-term electrical stability measurements, including current/bias stress and aging over 18 months of idle shelf life are presented for GIZO-based TFTs. The effects of oxygen partial pressure, annealing temperature and passivation are discussed. Optimized devices show highly stable properties, such as a recoverable ΔVT<0.5 V after 24h of 1D=10 μA stress, quite promising for integration in electronic circuits.

Long-term electrical stability measurements, including current/bias stress and aging over 18 months of idle shelf life are presented for GIZO-based TFTs. The effects of oxygen partial pressure, annealing temperature and passivation are discussed. Optimized devices show highly stable properties, such as a recoverable ΔV T<0.5 V after 24h of I D=10 μA stress, quite promising for integration in electronic circuits. © 2010 SID.

High performance transparent thin-film transistors deposited on glass substrates and entirely processed at a low temperature not exceeding 150°C are presented and analyzed in this paper. Besides being based on an amorphous oxide semiconductor, the main innovation of this work relies on the use of sputtered multicomponent oxides as dielectric materials based on mixtures of Ta2O5 with SiO2 or Al2O3. These multicomponent dielectrics allow to obtain amorphous structures and low leakage currents while preserving a high dielectric constant. This results in transistors with remarkable electrical properties, such as field-effect mobility exceeding 35 cm2 V-1 s-1, close to 0 V turn-on voltage, on/off ratio higher than 106, and a subthreshold slope of 0.24 V decade-1, obtained with a Ta2O5: SiO2 dielectric. When subjected to severe current stress tests, optimized devices show little and reversible variation in their electrical characteristics. The devices presented here have properties comparable to the ones using plasma-enhanced chemical vapor deposited SiO2 at 400°C, reinforcing the success of this amorphous multicomponent dielectric approach for low temperature, high performance, and transparent electronic circuits. © 2009 The Electrochemical Society.

The authors report on the performance of polymer-based light-emitting diodes, LEDs, using amorphous zinc oxide-doped indium oxide, IZO, as anode. In particular, LEDs with poly[(2-methoxy-5-(2′-ethyl-hexyloxy)-1,4-phenylene vinylene] as electroluminescent layer and aluminium cathodes, show higher efficiency with this IZO anode (0.015 cd/A) than with indium-tin oxide (ITO) (0.010 cd/A). Inspite of the higher resistance of this IZO electrode, compared with ITO, the fact that it can be processed at lower temperatures and allows similar or even higher efficiency values for polymer LEDs make this material a good candidate for display and other optoelectronic applications. © 2009 Elsevier B.V. All rights reserved.

This work analyzes the role of processing parameters on the electrical performance of GIZO (Ga2 O3: In2 O3:ZnO) films and thin-film transistors (TFTs). Parameters such as oxygen partial pressure, deposition pressure, target composition, thickness, and annealing temperature are studied. Generally, better devices are obtained when low oxygen partial pressure is used. This is related to the damage induced by oxygen ion bombardment and very high film's resistivity when higher oxygen partial pressures are used. Low deposition pressures and targets with richer indium compositions led to films with high carrier concentration, resulting in transistors with field-effect mobility as high as ∼80 cm2 Vs but poor channel conductivity modulation, becoming ineffective as switching devices. Nevertheless, it is demonstrated that reducing the GIZO thickness from 40 to 10 nm greatly enhances the switching behavior of those devices, due to the lower absolute number of free carriers and hence to their easier depletion. Annealing also proves to be crucial to control device performance, significantly modifying GIZO electrical resistivity and promoting local atomic rearrangement, being the optimal temperature determined by the as-produced films' properties. For the best-performing transistors, even with a low annealing temperature (150°C), remarkable properties such as μFE =73.9 cm2 Vs, onoff ratio≈7× 107, VT ≈0.2 V, and S=0.29 Vdec are achieved. © 2008 The Electrochemical Society.

The influence of oxygen content, radio-frequency (rf) sputtering power, and postdeposition annealing on the electrical properties of gallium-indium-zinc oxide (GIZO) thin-film transistors (TFTs) is analyzed. Little to no oxygen content in the sputtering chamber is crucial to obtain high-performance devices, even before annealing. In contrast, a high oxygen content and rf power lead, respectively, to unstable/poor performing and depletion mode TFTs before annealing, and mainly for these "nonideal" conditions, annealing proves to be effective to improve device performance/stability and to decrease the performance discrepancy among TFTs processed under different oxygen and rf power conditions. Best TFTs present a field-effect mobility of 46 cm2 / V s, subthreshold swing of 0.26 V/dec, threshold voltage of 0.70 V, and an on/off ratio 108 - 109. These results are a consequence of the optimized processing and of the usage of proper GIZO target composition, 1:2:1 mol. © 2008 The Electrochemical Society.

During the last years, oxide semiconductors have shown that they will have a key role in the future of electronics. In fact, several research groups have already presented working devices with remarkable electrical and optical properties based on these materials, mainly thin-film transistors (TFTs). Most of these TFTs use indium-tin oxide (ITO) as the material for source/drain electrodes. This paper focuses on the investigation of different materials to replace ITO in inverted-staggered TFTs based on gallium-indium-zinc oxide (GIZO) semiconductor. The analyzed electrode materials were indium-zinc oxide, Ti, Al, Mo, and Ti/Au, with each of these materials used in two different kinds of devices: one was annealed after GIZO channel deposition but prior to source/drain deposition, and the other was annealed at the end of device production. The results show an improvement on the electrical properties when the annealing is performed at the end (for instance, with Ti/Au electrodes, mobility rises from 19 to 25 cm2/V · s, and turn-on voltage drops from 4 to 2 V). Using time-of-flight secondary ion mass spectrometry (TOF-SIMS), we could confirm that some diffusion exists in the source/drain electrodes/ semiconductor interface, which is in close agreement with the obtained electrical properties. In addition to TOF-SIMS results for relevant elements, electrical characterization is presented for each kind of device, including the extraction of source/drain series resistances and TFT intrinsic parameters, such as VTi (intrinsic threshold voltage). © 2008 IEEE.

Indium tin oxide (ITO) has been used as the prefered electrode material for the emerging area of transparent electronics, namely for thin-film transistors (TFTs) based on oxide semiconductors. This work pretends to investigate different materials to replace ITO in inverted-staggered TFTs based on gallium-indium-zinc oxide (GIZO), one of the most promissing oxide semiconductors for TFTs. The analyzed electrode materials are indium-zinc oxide (IZO), Ti, Mo and Ti/Au. Devices are analyzed with special focus on the contact resistance fundamentals, including the extraction of source/ drain series resistances and TFTs intrinsic parameters, such as intrinsic mobility (p\) and intrinsic threshold voltage (V Ti). The obtained contact resistance values are between 10 kΩ and 20 kΩ, and the best devices have field effect mobility ((μ FE) close to 25 cm 2/V s and on/off ratio close to 10 8. © 2008 WILEY-VCH Verlag GmbH & Co. KGaA.

This work shows the effect of the annealing temperature and atmosphere on the properties of r.f. magnetron sputtered indium-zinc oxide (IZO) thin-films of two types: one a conductive film (as-deposited, room temperature) that exhibits a resistivity of 3.5 × 10- 4 Ω cm; the other, a semiconductor film with a resistivity ∼ 102 Ω cm. The annealing temperatures were changed between 125 and 500 °C. Crystallization of the more conductive films was already noticeable at temperatures around 400 °C. Three different annealing atmospheres were used - vacuum, air and oxygen. For the conductive films, only the oxygen atmosphere was critical, leading to an increase of the electrical resistivity of more than one order of magnitude, for temperatures of 250 °C and above. Concerning the semiconductor films, both temperature and atmosphere had a strong effect on the film's properties, and the resistivity of the annealed films was always considerably smaller than the as-deposited films. Finally, some results of the application of these films to transparent TFTs are shown. © 2007 Elsevier B.V. All rights reserved.

Insensitivity to light irradiation is desirable for conventional applications of thin-film transistors, i.e., the active matrices of displays. However, if one produces a device presenting controlled sensitivity to light, many other applications can benefit or can even be created. In this work it is shown the influence of the photon energy on the optoelectronic properties presented by n-type bottom-gate thin-film transistors based on indium zinc oxide. In the dark, the devices present very good electrical properties, working in the enhancement mode, exhibiting on-off ratios higher than 107 and channel mobility above 30 cm2/V s. Remarkable results were achieved when the devices were exposed to light radiation, the most striking one is the possibility to switch between enhancement (in the dark) and depletion (illuminated) modes, with different threshold voltages and on/off ratios, function of the light power density and wavelength used. This type of behavior permits to design circuits where one can have the same transistor working either in the enhancement or depletion modes, function of the light beam and intensity impinging on it, highly important for short wavelength detector applications. © 2006 Elsevier B.V. All rights reserved.

Multicomponent amorphous oxides are starting to emerge as a class of appealing semiconductor materials for application in transparent electronics. In this work, a high performance bottom-gate n-type transparent thin-film transistors are reported, being the discussion primarily focused on the influence of the indium zinc oxide active layer thickness on the properties of the devices. For this purpose, transparent transistors with active layer thicknesses ranging from 15 nm to 60 nm were produced at room temperature using rf magnetron sputtering. Optical transmittance data in the visible range reveals average transmittance higher than 80%, including the glass substrate. The devices work in the enhancement mode and exhibit excellent saturation drain currents. On-off ratios above 107 are achieved, but this value tends to be lower for devices with thicker semiconductor films, as a result of the decrease in the resistance of the channel region with increasing thickness. Channel mobilities are also quite respectable, with some devices presenting values around 40 cm2/V s, even without any annealing or other post-deposition improvement processes. Concerning the evolution of threshold voltage with the thickness, this work shows that it increases from about 3 V in thicker films up to about 10 V in the thinnest ones. The interesting electrical properties obtained and the versatility arising from the fact that it is possible to modify them changing only the thickness of the semiconductor makes this new transparent transistors quite promising for future transparent ICs. © 2006 Elsevier B.V. All rights reserved.

In this work we present a study concerning the influence of some of the most important external factors on the electrical properties of transparent thin-film transistors (TFTs), using zinc oxide produced at room temperature as the semiconductor material. Electrical characterization performed sixteen months after the production of the devices showed a decrease in the on/off ratio from 8×105 to 1×105, mainly due to the increase of the off-current. We also observed a small increase in the saturation mobility, a decrease in the threshold voltage and an increase in the gate voltage swing (by factors of about 1.2, 0.9 and 1.6, respectively). Exposure to ambient light does not have a noticeable effect on the electrical properties, which is an important point as regards the application of these devices in active matrix displays. Some variation of the electrical properties was only detectable under intense white light radiation. In order to evaluate the temperature effect on the TFTs, they were also characterized at 90 °C. At this temperature we noticed that the off-current increased more than two times, and the other electrical properties had a small variation, returning to their initial values after cooling, meaning that the process is totally reversible. © 2005 Elsevier Ltd. All rights reserved.

The purpose of this work is to present in-depth electrical characterization on transparent TFTs, using zinc oxide produced at room temperature as the semiconductor material. Some of the studied aspects were the relation between the output conductance in the post-pinch-off regime and width-to-length ratios, the gate leakage current, the semiconductor/insulator interface traps density and its relation with threshold voltage. The main point of the analysis was focused on channel mobility. Values extracted using different methodologies, like effective, saturation and average mobility, are presented and discussed regarding their significance and validity. The evolution of the different types of mobility with the applied gate voltage was investigated and the obtained results are somehow in disagreement with the typical behavior found on classical silicon based MOSFETs, which is mainly attributed to the completely different structures of the semiconductor materials used in the two situations: while in MOSFETS we have monocrystalline silicon, our transparent TFTs use poly/nanocrystalline zinc oxide with grain sizes of about 10 nm.

This work refers to the electro-optical and structural characteristics of titanium oxide (TiOx) thin films produced by radio frequency (r.f.) magnetron sputtering that present promising performances for gate dielectric applications, alone or in mixed tandem structures, such as with Al yOz films, taking advantage of its high dielectric constant. Films produced with a O2/Ar ratio between 0.1 and 0.15 present an improved stochiometry and density where the resistivity overcomes 1011 Ω cm and the fixed charge density decreases below 10 12 cm-2. The deposition pressure influences greatly the growth rate that seems to be a determinant factor dictating the films properties. © 2004 Elsevier Ltd. All rights reserved.

In this letter we compare the room temperature ozone sensing properties of intrinsic zinc oxide (ZnO) thin films deposited by spray pyrolysis, dc and r.f. magnetron sputtering. Their sensor response exceeds 8 orders of magnitude when the film structure is constituted by nanocrystallites. These preliminary results clearly demonstrate that the films could be potentially used for ozone detection at room temperature.

In this paper we present an improved version of large area (5 mm × 80 mm) flexible position sensitive detectors deposited on polyimide (Kapton® VN) substrates with 75 μm thickness, produced by plasma enhanced chemical vapor deposition (PECVD). The structures presented by the sensors are Kapton/ZnO:Al/(pin)a-Si:H/Al and the heterostructure Kapton/Cr/(in)a-Si:H/ZnO:Al. These sensors were characterized by spectral response, photocurrent dependence as a function of light intensity and position detectability measurements. The set of data obtained on one-dimensional position sensitive detectors based on the heterostructure show excellent performances with a maximum spectral response of 0.12 A/W at 500 nm and a non-linearity of ±10%. © 2002 Elsevier Science B.V. All rights reserved.

The room temperature ozone sensing properties of polycrystalline undoped zinc oxide (ZnO) thin films have been investigated. ZnO thin films have been produced by the d.c. and r.f. magnetron sputtering technique as well as with spray pyrolysis with a variety of parameters. The as-grown films were brought to a high conducting state through a reversible photoreduction process by UV light exposure and were subsequently exposed to ozone resulting in a strong resistivity increase caused by re-oxidation. The magnitude of the effect was largest for the sputtered films, which exhibited resistivity changes of more than 8 orders of magnitude, whereas films deposited by spray pyrolysis showed changes of less than 3 orders of magnitude. XRD and AFM analysis of the films revealed that all films were microcrystalline. The film texture, however, was strongly related to the growth technique and the parameters used. Best results were achieved with r.f.-sputtered films, which have been deposited at high total pressures. These films exhibited a sensor response of 1.2 × 108. © 2002 Elsevier Science B.V. All rights reserved.

This paper presents results of the role of the oxygen concentration (CO) and the deposition pressure (pd) on structural and electrical properties of indium tin oxide films produced by r.f. magnetron sputtering. The films were annealed in air, followed by a reannealed stage in hydrogen, aiming to improve the film's transparency and conductivity. The results achieved show that the films texture grain size, structure and compactness is more influenced by CO than by pd, the same does not happen with the electrical properties.

This work refers to the main electro-optical characteristics exhibited by large area indium tin oxide films (300 × 400 mm) produced by r.f. magnetron sputtering under different oxygen concentrations and deposition pressures. Besides that, the ageing effect on the electro-optical characteristics of the films produced was also analyzed. The results achieved show that the film transparency and conductivity were highly improved (more than four orders of magnitude) by first annealing them in air at 470°C, followed by a reannealed stage under vacuum, in a hydrogen atmosphere, at 350°C. The ageing tests show that film degradation occurs when the films are produced at oxygen concentrations above 10% and/or at deposition pressures above 1.2 × 10-2 mbar. © 1999 Elsevier Science S.A. All rights reserved.

Electrical dark conductivity (σd) and surface composition of undoped and doped a-Si:H thin films have been investigated, using coplanar I−V as a function of temperature and Auger electron spectroscopy (AES). The films were prepared by rf glow discharge deposition on standard soda-lime glass and on alkali-free glass substrates. Comparing these two sets of substrates for undoped films, we find that σd of the films deposited on soda-lime glass substrates at room temperature is higher by more than two orders of magnitude, their activation energy is lower by about a factor of 3, and their photosensitivity (σph/σd) is lower by two orders of magnitude than that of the films deposited on alkali-free glass substrates. We suggest that Na ions, leached from the glass into the a-Si:H overlayer play a significant role in determining the film conductivity by creating electrically active donorlike states. This conclusion is supported by similar measurements on p- and n-type a-Si:H films on the same substrates and by AES results. Films of a-Si:H, grown on thin a-Si:C:H interlayers on soda-lime glass, showed very low Na concentrations and low dark conductivities as found by AES and electrical measurements, respectively. The role of the a-Si:C:H interlayers as diffusion barriers is discussed. © 1989, American Vacuum Society. All rights reserved.