Rodrigo Martins

Complex impedance measurements were used to analyze the influence of ultraviolet and ozone gas on the electronic behaviour of ZnO films grown by rf magnetron sputtering. The data show that UV exposure strongly increases the ac conductivity of the film at very low frequencies, and that after ozone exposure it recovers the original value. At high frequencies, however, UV-light exposure it does not change the conductivity but the ozone acts in the sense to decrease it. Two distinct mechanisms, related to two relaxation time distributions are clearly observed: they are superimposed in the virgin sample, but they split forming two semicircles in the z″(f) - z′(f) diagrams when the samples are treated with UV and/or ozone gas. A combination of the bruggeman effective medium approximation (BEMA) with the random free energy barrier model is used to fit the data and to explain the ac conductivity variation phenomena observed. © 2006 Elsevier B.V. All rights reserved.

In this work, the relation between oxidant/monomer ratio and the electrical conductivity of polypyrrole was studied using different ratios. We achieved a maximum value for electrical conductivity of 7.5 S/cm for a ratio of 2:1. We also developed a chemical dip-coating process to produce the cathode layer in tantalum capacitors. We obtained capacitances of about 80 μF after 8 cycles using the sequence Monomer/Oxidant.

The aim of this paper is to present results on a new soldering process based on the low-temperature solidification of intermetallic phases from the system Cu-Sn-Cu which can be employed to form a heat-resistant die-attach as well as signal and power electric contacts. Because of the total transformation into intermetallic phase, the working temperature of the bond formed is several hundred degrees Celsius higher than the process temperature (around 250°C). This process leads to a homologous temperature T/Tm of about 0.3 compared to 0.7 in the case of soft SnAg solder alloy. Therefore a better reliability of the proposed bonding process is achievable. Results of the match of the predicted volume fraction of the intermetallic forms and the experimentally measured contact volume would be also discussed, for contacts formed in power diodes.

In this work we studied indium zinc oxide (IZO) thin films deposited by r.f. magnetron sputtering at room temperature. The films were annealed at high temperature (1100 K) in vacuum, and the oxygen exodiffusion was monitored in-situ. The results showed three main peaks, one at approximately 600 K, other at approximately 850 K and the last one at 940 K, which are probably from oxygen bonded in the film surface and in the bulk, respectively. The initial amorphous structure becomes microcrystalline, according to the X-ray diffraction. The electrical conductivity of the films decreases (about 3 orders of magnitude), after the annealing treatment. This behavior could be explained by the crystallization of the structure, which affects the transport mechanism. Apart from the changes in the material structure, a small variation was observed on the absorption coefficient. © 2007 Elsevier B.V. All rights reserved.

This paper reports the application of a polymethacrylate hydroxyethylene resin based electrolyte in electrochromic (EC) devices. The electrolyte is characterized by electrochemical impedance spectroscopy, visible spectroscopy, TGA, DSC, and DRX and tested as an ionic conductor in an EC device with the following configuration: Substrate/IZO/WO 3/Polymer Electrolyte/(CeO 2)TiO 2/IZO/Substrate. The electrolyte presents an ionic conductivity of 10 -7S/cm at room temperature and TGA analysis show that electrolyte is thermally degraded at 200°C. The EC device based on this polymethacrylate hydroxyethylene resin electrolyte system shows memory effect and exhibits an excellent optical density. © 2011 John Wiley & Sons, Ltd.

Electrochromic materials have attracted considerable attention during the last two decades as a consequence of their potential application in several different types of optical devices. Examples of these devices include intelligent windows and time labels. In this paper the authors describe results obtained with thin tungsten oxide films produced at room temperature by rf magnetron sputtering under an argon and oxygen atmosphere on transparent conductive oxide coated glass substrates. To protect the surface of the electrochromic film, prevent water absorption and obtain a good memory effect under open circuit voltages, a layer of Ta2O5 was deposited over the WO3 films. In this study, the effect of different electrolyte compositions on the open circuit memory of optical devices has been characterized. The best results were obtained for electrochromic devices with polymer gel p(TMC)3LiC1O4 and p(TMC)8LiClO 4 electrolytes. These prototype devices present an overall transmittance of ∼75% in their bleached state and after coloration 40.5 and 52.5% respectively. These devices also show memory effect and an optical density considered satisfactory for some electrochromic applications.

In this work we present a study on the effect of annealing temperatures on the structural, morphological, electrical and optical characteristics of gallium doped zinc oxide (GZO), indium zinc oxide (IZO) and indium-tin-oxide (ITO) films. GZO and IZO films were deposited at room temperature by r.f. magnetron sputtering, whereas the ITO films were commercial ones purchased from Balzers. All films were annealed at temperatures of 250 and 500 °C in open air for 1 h. The GZO and ITO films were polycrystalline. The amorphous structure of as-deposited IZO films becomes crystalline on high temperature annealing (500 °C). The sheet resistivity increased with increase in annealing temperature. GZO films showed an increase of 6 orders of magnitude. The optical transmittance and band gap of as-deposited films varied with annealing. The highest transmittance (over 95 %) and maximum band gap (3.93 eV) have been obtained for ITO films. © 2007 Elsevier B.V. All rights reserved.

In this paper, the role of electrode architecture (conventional and interdigital), device structure (vertical or planar), and tungsten oxide (WO3) channel thickness on the electro-optical performances of room temperature sputtered electrochromic transistors (EC-Ts) is reported. A larger number of electro-reducible tungsten sites in thicker WO3 films provide improved optical density and coloration efficiency. However, overall transistor performance is found to suffer in planar EC-Ts with the conventional electrode architecture, where the step to planar interdigital electrodes leaves the devices to be almost insensitive to WO3 thickness. Vertical structures result in improved device properties and stability, given to the shorter distance between gate electrode and semiconductor and to the encapsulation effect provided by such structures. These devices show an On–Off ratio of 5 × 106 and a transconductance (g m) of 3.59 mS, for gate voltages (V G) between −2 and 2 V, which to the authors' knowledge are the best values ever reported for electrochemical transistors. The simple and low-cost processing together with the electrical/optical performances well supported into a comprehensive analysis of device physics opens doors for a wide range of new applications in display technologies, biosensors, fuel cells, or electrochemical logic circuits. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

In previous papers the mean excess chemical potential, μ1(E), in ternary systems of the type I sulphate + II sulphate + H2O, at 25°C was determined. Results obtained for systems with CuSO4(I), and ZnSO4(I) respectively, pointed out an obvious disparity between their behaviours. They show the existence of some important association phenomena partially accounting for the substantial deviations from ideal behaviour. The ternary sulphate systems (CuSO4 + Me(I,II)SO4 + H2O; ZnSO4 + Me(I,II)SO4 + H2O) studied were characterized against the binaries of the same ionic strength, experimental data being obtained using both e.m.f. and spectrophotometric methods. Deviations from the ideal behaviour were discussed in terms of thermodynamic excess functions and association constants. A comparative study between the results obtained with the two above mentioned methods is presented. In previous papers the mean excess chemical potential, μ1 E, in ternary systems of the type I sulphate+II sulphate+H2O, at 25 °C was determined. Results obtained for systems with CuSO4(I), and ZnSO4(I) respectively, pointed out an obvious disparity between their behaviours. They show the existence of some important association phenomena partially accounting for the substantial deviations from ideal behaviour. The ternary sulphate systems (CuSO4+MeI, IISO4+H2O; ZnSO4+MeI, IISO4+H2O) studied were characterized against the binaries of the same ionic strength, experimental data being obtained using both e.m.f. and spectrophotometric methods. Deviations from the ideal behaviour were discussed in terms of thermodynamic excess functions and association constants. A comparative study between the results obtained with the two above mentioned methods is presented.

The need to improve the efficiency of the European university system is discussed. It is considered possible to increase university funding by letting students pay for their education. It is suggested that European universities raise more money for research from private sources by selling services. It is found appropriate to strive for excellence at the level of specific departments or schools to begin with.

Undoped and doped hydrogenated amorphous silicon semiconductors (a-Si:H) have been produced by a two consecutive decomposition deposition chamber (TCDDC) system assisted by electromagnetic static fields. Through this technique, a spatial separation is achieved between the plasma chemistry and that of the deposition to avoid ion and electron (with high energies) bombardment on the growing surface. Besides this, the use of a static magnetic field perpendicular to the substrate will promote plasma confinement, so avoiding its contamination by residual gases adsorbed on the reactor walls. On the other hand, the use of two grids dc biased in the deposition chamber, will allow control of the main film precursors, responsible for the electro-optical and structural properties of deposited films. In this paper we shall discuss the deposition method used as well as the transport, structural and morphological properties presented by deposited films and its dependence on deposition parameters used. © 1989.

A wide bandgap and highly conductive p-type hydrogenated nanocrystalline silicon (nc-Si:H) window layer was prepared with a conventional RF-PECVD system under large H dilution condition, moderate power density, high pressure and low substrate temperature. The optoelectrical and structural properties of this novel material have been investigated by Raman and UV-VIS transmission spectroscopy measurements indicating that these films are composed of nanocrystallites embedded in amorphous SiHx matrix and with a widened bandgap. The observed downshift of the optical phonon Raman spectra (514.4 cm-1) from crystalline Si peak (521 cm-1) and the widening of the bandgap indicate a quantum confinement effect from the Si nanocrystallites. By using this kind of p-layer, a-Si:H solar cells on bare stainless steel foil in nip sequence have been successfully prepared with a Voc of 0.90 V, a fill factor of 0.70 and an efficiency of 9.0%, respectively. © 2006 Elsevier B.V. All rights reserved.

Solution-processed metal-oxide thin films with high dielectric constants (k) have been extensively studied for low-cost and high-performance thin-film transistors (TFTs). In this report, MgO dielectric films were fabricated using the spin-coating method. The MgO dielectric films annealed at various temperatures (300, 400, 500, and 600 °C) were characterized by using thermogravimetric analysis, optical spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and atomic-force microscopy. The electrical measurements indicate that the insulating properties of MgO thin films are improved with an increase in annealing temperature. In order to clarify the potential application of MgO thin films as gate dielectrics in TFTs, solution-derived In2O3 channel layers were separately fabricated on various MgO dielectric layers. The optimized In2O3/MgO TFT exhibited an electron mobility of 5.48 cm2/V s, an on/off current ratio of 107, and a subthreshold swing of 0.33 V/dec at a low operation voltage of 6 V. This work represents a great step toward the development of portable and low-power consumption electronics. © 2016 Author(s).

Oxide semiconductor thin-film transistors can show anomalous behavior under bias stress. Two types of anomalies are discussed in this paper. The first is the shift in threshold voltage (VTH) in a direction opposite to the applied bias stress, and highly dependent on gate dielectric material. We attribute this to charge trapping/detrapping and charge migration within the gate dielectric. We emphasize the fundamental difference between trapping/detrapping events occurring at the semiconductor/dielectric interface and those occurring at gate/dielectric interface, and show that charge migration is essential to explain the first anomaly. We model charge migration in terms of the non-instantaneous polarization density. The second type of anomaly is negative VTH shift under high positive bias stress, with logarithmic evolution in time. This can be argued as electron-donating reactions involving H2O molecules or derived species, with a reaction rate exponentially accelerated by positive gate bias and exponentially decreased by the number of reactions already occurred. © 2016 Author(s).

It is shown that the electronic properties of amorphous germanium (a-Ge) prepared by the glow-discharge decomposition of germane can be controlled systematically by substitutional phosphorus doping from the gas phase. Specimens with different doping levels have' been investigated by conductivity, thermoelectric power and Hall effect measurements in a temperature range between 160 and 450 K. The dependence of conductivity on doping level is qualitatively similar to that in a-Si, but the range of control is limited in a-Ge by the smaller mobility gap. Also the larger overall density of gap states in this material reduces the doping sensitivity. The above transport measurements and their temperature dependence can be interpreted in a quantitatively consistent manner- by a two-path model in which conduction takes place in the extended states and in another path through the localized states. As 111 a-Si, the photoconductivity of glow-discharge Ge can be appreciably sensitized by phosphorus doping. The μτ product deduced from such experiments on a-Ge and a-Si are compared for different preparation techniques. The data show that irrespective of the presence of hydrogen the method of deposition remains an important factor in determining the density of gap states. © 1979 Taylor & Francis Ltd.

Ferroelectric and high dielectric permittivity films are currently being investigated in view of their use as gate dielectrics in MIS structures. Along with the suppression of tunnelling currents at small gate thickness, they provide a memory function to MIS structures, which can be used in non-volatile memory applications. In this work we report fabrication and characterization of novel metal-ferroelectric-amorphous silicon structures. The structures consist of glass/ITO substrates coated with PZT 20/80 films (sol-gel) followed by an active layer (i-a-SiC:H, deposited by plasma enhanced chemical vapor deposition (PECVD)). A strong capacitance hysteresis is observed in C-V curves in electron accumulation region (VG > 0), accompanied with a large increase in the capacitance of ferroelectric-semiconductor structures at low frequencies. Threshold voltage for electron accumulation is about 10 V being dependent on the ferroelectric polarization switching. © 2002 Elsevier Science B.V. All rights reserved.

PbZrxTi1-xO3 (PZT) films are currently being investigated in view of their large switching polarization and piezoelectric coefficients useful for various applications. Besides, PZT films possess large photosensitivity, which, in combination with the above listed properties, can be a base for future microelectronic applications including photostrictive actuators and optical storage devices. In this work, PZT thin films of several compositions (x=0.2 and 0.45) were deposited on Pt-coated Si and ITO/glass substrates via modified sol-gel technique. Microstructures of the films were evaluated using XRD, SEM and AFM. The optical transmission measurements on PZT films deposited on ITO/glass revealed a high transparency over 80% and a band gap of about 3.4 eV. The observed photocurrent exhibited a maximum and was attributed to band-to-band optical transitions.

The impact of a parylene top-coating layer on the illumination and bias stress instabilities of indium-gallium-zinc oxide thin-film transistors (TFTs) is presented and discussed. The parylene coating substantially reduces the threshold voltage shift caused by continuous application of a gate bias and light exposure. The operational stability improves by 75%, and the light induced instability is reduced by 35%. The operational stability is quantified by fitting the threshold voltage shift with a stretched exponential model. Storage time as long as 7 months does not cause any measurable degradation on the electrical performance. It is proposed that parylene plays not only the role of an encapsulation layer but also of a defect passivation on the top semiconductor surface. It is also reported that depletion-mode TFTs are less sensitive to light induced instabilities. This is attributed to a defect neutralization process in the presence of free electrons. © 2016 Author(s).

In this study, we report solution-processed amorphous zinc tin oxide transistors exhibiting high operational stability under positive gate bias stress, translated by a recoverable threshold voltage shift of about 20% of total applied stress voltage. Under vacuum condition, the threshold voltage shift saturates showing that the gate-bias stress is limited by trap exhaustion or balance between trap filling and emptying mechanism. In ambient atmosphere, the threshold voltage shift no longer saturates, stability is degraded and the recovering process is impeded. We suggest that the trapping time during the stress and detrapping time in recovering are affected by oxygen adsorption/desorption processes. The time constants extracted from stretched exponential fitting curves are ∼106 s and 105 s in vacuum and air, respectively. © 2015 Author(s).

Titanium oxide (TiO 2) finds potential applications in various fields such as solar cells, optical coatings due to its high refractive index and it also has been widely used in memory devices owing to its high dielectric constant. TiO 2 films have been deposited on p-type silicon (100) substrates by RF magnetron sputtering technique. Thickness, structure and surface morphology of the films were analyzed by using α-step profilometer, Raman spectroscopy and atomic force microscope respectively. Thin film capacitors of the type Al/TiO 2/Si were fabricated by evaporation of Aluminium on to the TiO 2 films. The current - voltage and capacitance - voltage characteristics were carried out to understand the electrical conduction and dielectric properties of the deposited films with a stack of Al/TiO 2/Si. The leakage current density was decreased and capacitance was increased with increase of substrate bias voltage.

We demonstrate fully transparent, highly rectifying contacts (TRC) on amorphous GaInZnO and compare them to TRC fabricated on single crystalline bulk ZnO and heteroepitaxial ZnO thin films. The contacts' transparency in the visible spectral range exceeds 70%. From numerical simulations, we conclude that thermionic emission is the dominating transport mechanism, however, for several samples with low net doping density diffusion theory must be applied. The detailed investigation of the rectification properties of the TRC using temperature-dependent current-voltage and capacitance-voltage measurements reveals that barrier inhomogeneities govern the IV-characteristics of all diodes irrespective of the sample crystallinity. Assuming a Gaussian barrier height distribution, the extracted mean barrier heights typically range between 1.1 and 1.3 V. The width of the barrier distribution correlates with the mean barrier height and ranges from 110 to 130 mV. By compiling literature data, we found that this correlation holds also true for Schottky diodes on elemental and III-V semiconductors. © 2013 American Institute of Physics.

Experimental results on structure defects in microcrystalline (μc) n- and p-doped μc-S1-x:Cx:H films deposited on alkali-free glass substrates by spatial plasma separation1 and obtained by electron paramagnetic resonance (EPR) are presented. The technique used for subtracting the substrate effect on recorded spectra is also discussed as well as its quantification. The microscopic structure of intrinsic defects and impurity states and their role in transport mechanisms are studied and correlated with the composition of their films. These results are also related to transport properties of deposited films in order to observe the role of dopant centres, located at conduction band tails, in controlling the electrical properties. © 1989.

In this paper we present a study on the electrical characteristics (conductivity, σ and relative dielectric constant, εr) of amorphous silicon nitride (a-SixN1-x) and carbide (a-SixC1-x) films deposited by PECVD, used as dielectric materials in TFT devices, aiming to select the most adequate alloy that lead to improve device performances. Besides that, double stack a-SixN1-x/a-SixC1-x structures were developed and applied as dielectric layers on TFTs, whose performances show to be superior to those ones using single silicon nitride or silicon carbide as dielectric.