Rodrigo Martins

This letter presents a novel high-gain four-quadrant analog multiplier using only n-type enhancement indium- gallium-zinc-oxide thin-film-transistors. The proposed circuit improves the gain by using an active load with positive feedback. A Gilbert cell with a diode-connected load is also presented for comparison purposes. Both circuits were fabricated on glass at low temperature (200 °C) and were successfully characterized at room temperature under normal ambient conditions, with a power supply of 15 V and 4-pF capacitive load. The novel circuit has shown a gain improvement of 7.2 dB over the Gilbert cell with the diode-connected load. Static linearity response, total harmonic distortion, frequency response, and power consumption are reported. This circuit is an important signal processing building block in large-area sensing and readout systems, specially if data communication is involved. © 2016 IEEE.

A dye sensitized TiO2 photodetector has been integrated with a DNA detection method based on non-cross-linking hybridization of DNA-functionalized gold nanoparticles, resulting in a disposable colorimetric biosensor. We present a new approach for the fabrication of dye sensitized TiO2 photodetectors by an inkjet printing technique-a non-contact digital, additive, no mask and no vacuum patterning method, ideal for cost efficient mass production. The developed biosensor was compared against a dye sensitized photodetector fabricated by the traditional "doctor blade" method. Detection of gold nanoparticle aggregation was possible for concentrations as low as 1.0 nM for the "doctor blade" system, and 1.5 nM for the inkjet printed photodetector. The demonstrated sensitivity limits of developed biosensors are comparable to those of spectrophotometric techniques (1.0 nM). Our results show that a difference higher than 17% by traditional photodetector and 6% by inkjet printed in the photoresponses for the complementary and non-complementary gold nanoprobe assays could be attained for a specific DNA sequence from Mycobacterium tuberculosis, the etiologic agent of human tuberculosis. The decrease of costs associated with molecular diagnostic provided by a platform such as the one presented here may prove of paramount importance in developing countries. © 2009 Elsevier B.V. All rights reserved.

The aim of presented work is to show the improvements obtained in the properties of TiO2 films for dye sensitized solar cells fabricated by inkjet printing using an innovative methodology. We describe the development and properties of TiO2-based inks used in a lab-scale printer, testing various commercial TiO2 pastes. The porosity of the deposited inkjet printed TiO2 films is much higher than using the conventional "doctor blade" deposition technique, as the ink solvent evaporates during the droplet fly from the nozzle to the substrate due to its picoliter volume and the applied heating of a printing stage (70°C). Thanks to higher surface area, the dye sensitized solar cells incorporating inkjet printed TiO2 film gave higher efficiencies (ηmax≈3.06%) than the more compact films obtained by the "doctor blade" method (ηmax≈2.56%). Furthermore, electrochemical analysis indicates that for whole tested thickness range, the inkjet printed layers have higher effective electron diffusion length indicating their better transport properties. © 2015 Elsevier Inc..

This paper discusses the properties of sputtered multicomponent amorphous dielectrics based on mixtures of high-κ and high-bandgap materials and their integration in oxide TFTs, with processing temperatures not exceeding 1 50° C. Even if Ta2O5 films are already amorphous, multicomponent materials such as Ta2O5-SiO2 and Ta2O5-Al2O3 allow an increase in the bandgap and the smoothness of the films, reducing their leakage current and improving (in the case of Ta2O5-SiO2)the dielectric/semiconductor interface properties when these dielectrics are integrated in TFTs. For HfO2- based dielectrics, the advantages of multicomponent materials are even clearer: while HfO2 films present a polycrystalline structure and a rough surface, HfO2-SiO2 films exhibit an amorphous structure and a very smooth surface. The integration of the multicomponent dielectrics in GIZO TFTs allows remarkable performance, comparable with that of GIZO TFTs using SiO2 deposited at 400°C by PECVD. For instance, with Ta2O5-SiO2 as the dielectric layer, field-effect mobility of 35 cm2/(V-sec), close to 0 V turn-on voltage, an on/off ratio higher than 106, a subthreshold slope of 0.24 V/dec, and a small/recoverable threshold voltage shifts under constant current (ID = 10 μ,A) stress during 24 hours are achieved. Initial results with multilayers of SiO2/HfO 2-SiO2/SiO2 are also shown, allowing a lower leakage current with lower thickness and excellent device performance. © Copyright 2010 Society for Information Display.

This chapter gives an overview about GIZO TFTs, comprising an introductory section about generic TFT structure and operation, different semiconductor technologies for TFTs - with special emphasis on AOSs and particularly on GIZO - and then some experimental results obtained for GIZO TFTs fabricated in CENIMAT. Thin-film transistors (TFTs) are important electronic devices which are predominantly used as On/Off switches in active matrix backplanes of flat panel displays (FPDs), namely liquid crystal displays (LCDs) and organic light emitting device (OLED) displays. Even if a-Si:H is still dominating the TFT market in terms of semiconductor technology, oxide semiconductors are emerging as one of the most promising alternatives for the next generation of TFTs, bringing the possibility of having fully transparent devices, low processing temperature, low cost, high performance and electrically stable properties [1, 2]. Amorphous oxide semiconductors (AOS) such as Gallium-Indium-Zinc oxide (GIZO) [3, 4], even if fabricated at temperatures below 150°, are currently capable of providing transistors with field-effect mobility (μFE) exceeding 20 cm2V-1 s-1, threshold voltage (VT) close to 0V, On/Off ratios above 108, subthreshold swing (S) around 0:20V dec-1 and fully recoverable VT shift (ΔVT) lower than 0.5V after 24 h stress with constant drain current of 10 μA. © Springer-Verlag Berlin Heidelberg 2012.

In this paper we present an improved version of large area (5 mm × 80 mm) flexible position sensitive detectors deposited on polyimide (Kapton® VN) substrates with 75 μm thickness, produced by plasma enhanced chemical vapor deposition (PECVD). The structures presented by the sensors are Kapton/ZnO:Al/(pin)a-Si:H/Al and the heterostructure Kapton/Cr/(in)a-Si:H/ZnO:Al. These sensors were characterized by spectral response, photocurrent dependence as a function of light intensity and position detectability measurements. The set of data obtained on one-dimensional position sensitive detectors based on the heterostructure show excellent performances with a maximum spectral response of 0.12 A/W at 500 nm and a non-linearity of ±10%. © 2002 Elsevier Science B.V. All rights reserved.

High performance transparent thin-film transistors deposited on glass substrates and entirely processed at a low temperature not exceeding 150°C are presented and analyzed in this paper. Besides being based on an amorphous oxide semiconductor, the main innovation of this work relies on the use of sputtered multicomponent oxides as dielectric materials based on mixtures of Ta2O5 with SiO2 or Al2O3. These multicomponent dielectrics allow to obtain amorphous structures and low leakage currents while preserving a high dielectric constant. This results in transistors with remarkable electrical properties, such as field-effect mobility exceeding 35 cm2 V-1 s-1, close to 0 V turn-on voltage, on/off ratio higher than 106, and a subthreshold slope of 0.24 V decade-1, obtained with a Ta2O5: SiO2 dielectric. When subjected to severe current stress tests, optimized devices show little and reversible variation in their electrical characteristics. The devices presented here have properties comparable to the ones using plasma-enhanced chemical vapor deposited SiO2 at 400°C, reinforcing the success of this amorphous multicomponent dielectric approach for low temperature, high performance, and transparent electronic circuits. © 2009 The Electrochemical Society.

This work refers to the main electro-optical characteristics exhibited by large area indium tin oxide films (300 × 400 mm) produced by r.f. magnetron sputtering under different oxygen concentrations and deposition pressures. Besides that, the ageing effect on the electro-optical characteristics of the films produced was also analyzed. The results achieved show that the film transparency and conductivity were highly improved (more than four orders of magnitude) by first annealing them in air at 470°C, followed by a reannealed stage under vacuum, in a hydrogen atmosphere, at 350°C. The ageing tests show that film degradation occurs when the films are produced at oxygen concentrations above 10% and/or at deposition pressures above 1.2 × 10-2 mbar. © 1999 Elsevier Science S.A. All rights reserved.

The effect of post-deposition annealing temperature on the pH sensitivity of room temperature RF sputtered +{\hbox{Ta}}-{2}{\hbox{O}}5 was investigated. Structural and morphological features of these films were analyzed before and after annealing at various temperatures. The deposited films are amorphous up to 600 +^{\circ}{\hbox{C}}+ and crystallize at 700 +^{\circ}{\hbox{C}}+ in an orthorhombic phase. Electrolyte-insulator- semiconductor (EIS) field effect based sensors with an amorphous +{\hbox{Ta}}-{2}{\hbox{O}}5 sensing layer showed pH sensitivity above 50 mV/pH. For sensors annealed above 200 +^{\circ}{\hbox{C}}+ pH sensitivity decreased with increasing temperature. Stabilized sensor response and maximum pH sensitivity was achieved after low temperature annealing at 200 +^{\circ}{\hbox{C}}+ , which is compatible with the use of polymeric substrates and application as sensitive layer in oxides TFT-based sensors. © 2005-2012 IEEE.

The authors report on the performance of polymer-based light-emitting diodes, LEDs, using amorphous zinc oxide-doped indium oxide, IZO, as anode. In particular, LEDs with poly[(2-methoxy-5-(2′-ethyl-hexyloxy)-1,4-phenylene vinylene] as electroluminescent layer and aluminium cathodes, show higher efficiency with this IZO anode (0.015 cd/A) than with indium-tin oxide (ITO) (0.010 cd/A). Inspite of the higher resistance of this IZO electrode, compared with ITO, the fact that it can be processed at lower temperatures and allows similar or even higher efficiency values for polymer LEDs make this material a good candidate for display and other optoelectronic applications. © 2009 Elsevier B.V. All rights reserved.

The room temperature ozone sensing properties of polycrystalline undoped zinc oxide (ZnO) thin films have been investigated. ZnO thin films have been produced by the d.c. and r.f. magnetron sputtering technique as well as with spray pyrolysis with a variety of parameters. The as-grown films were brought to a high conducting state through a reversible photoreduction process by UV light exposure and were subsequently exposed to ozone resulting in a strong resistivity increase caused by re-oxidation. The magnitude of the effect was largest for the sputtered films, which exhibited resistivity changes of more than 8 orders of magnitude, whereas films deposited by spray pyrolysis showed changes of less than 3 orders of magnitude. XRD and AFM analysis of the films revealed that all films were microcrystalline. The film texture, however, was strongly related to the growth technique and the parameters used. Best results were achieved with r.f.-sputtered films, which have been deposited at high total pressures. These films exhibited a sensor response of 1.2 × 108. © 2002 Elsevier Science B.V. All rights reserved.

We present a new approach for real-time monitoring of PCR amplification of a specific sequence from the human c-MYC proto-oncogene using a Ta 2O 5 electrolyte-insulator-semiconductor (EIS) sensor. The response of the fabricated EIS sensor to cycle DNA amplification was evaluated and compared to standard SYBR-green fluorescence incorporation, showing it was possible to detect DNA concentration variations with 30mV/μM sensitivity. The sensor's response was then optimized to follow in real-time the PCR amplification of c-MYC sequence from a genomic DNA sample attaining an amplification profile comparable to that of a standard real-time PCR. Owing to the small size, ease of fabrication and low-cost, the developed Ta 2O 5 sensor may be incorporated onto a microfluidic device and then used for real-time PCR. Our approach may circumvent the practical and economical obstacles posed by current platforms that require an external fluorescence detector difficult to miniaturize and incorporate into a lab-on-chip system. © 2011 Elsevier B.V.

Indium tin oxide (ITO) has been used as the prefered electrode material for the emerging area of transparent electronics, namely for thin-film transistors (TFTs) based on oxide semiconductors. This work pretends to investigate different materials to replace ITO in inverted-staggered TFTs based on gallium-indium-zinc oxide (GIZO), one of the most promissing oxide semiconductors for TFTs. The analyzed electrode materials are indium-zinc oxide (IZO), Ti, Mo and Ti/Au. Devices are analyzed with special focus on the contact resistance fundamentals, including the extraction of source/ drain series resistances and TFTs intrinsic parameters, such as intrinsic mobility (p\) and intrinsic threshold voltage (V Ti). The obtained contact resistance values are between 10 kΩ and 20 kΩ, and the best devices have field effect mobility ((μ FE) close to 25 cm 2/V s and on/off ratio close to 10 8. © 2008 WILEY-VCH Verlag GmbH & Co. KGaA.

The purpose of this work is to present in-depth electrical characterization on transparent TFTs, using zinc oxide produced at room temperature as the semiconductor material. Some of the studied aspects were the relation between the output conductance in the post-pinch-off regime and width-to-length ratios, the gate leakage current, the semiconductor/insulator interface traps density and its relation with threshold voltage. The main point of the analysis was focused on channel mobility. Values extracted using different methodologies, like effective, saturation and average mobility, are presented and discussed regarding their significance and validity. The evolution of the different types of mobility with the applied gate voltage was investigated and the obtained results are somehow in disagreement with the typical behavior found on classical silicon based MOSFETs, which is mainly attributed to the completely different structures of the semiconductor materials used in the two situations: while in MOSFETS we have monocrystalline silicon, our transparent TFTs use poly/nanocrystalline zinc oxide with grain sizes of about 10 nm.

Electrical dark conductivity (σd) and surface composition of undoped and doped a-Si:H thin films have been investigated, using coplanar I−V as a function of temperature and Auger electron spectroscopy (AES). The films were prepared by rf glow discharge deposition on standard soda-lime glass and on alkali-free glass substrates. Comparing these two sets of substrates for undoped films, we find that σd of the films deposited on soda-lime glass substrates at room temperature is higher by more than two orders of magnitude, their activation energy is lower by about a factor of 3, and their photosensitivity (σph/σd) is lower by two orders of magnitude than that of the films deposited on alkali-free glass substrates. We suggest that Na ions, leached from the glass into the a-Si:H overlayer play a significant role in determining the film conductivity by creating electrically active donorlike states. This conclusion is supported by similar measurements on p- and n-type a-Si:H films on the same substrates and by AES results. Films of a-Si:H, grown on thin a-Si:C:H interlayers on soda-lime glass, showed very low Na concentrations and low dark conductivities as found by AES and electrical measurements, respectively. The role of the a-Si:C:H interlayers as diffusion barriers is discussed. © 1989, American Vacuum Society. All rights reserved.

The present work proposes the development of a bio-battery composed by an ultrathin monolithic structure of an electrospun cellulose acetate membrane, over which was deposited metallic thin film electrodes by thermal evaporation on both surfaces. The electrochemical characterization of the bio-batteries was performed under simulated body fluids like sweat and blood plasma [salt solution - 0.9% (w/w) NaCl]. Reversible electrochemical reactions were detected through the cellulose acetate structure. Thus, a stable electrochemical behavior was achieved for a bio-battery with silver and aluminum thin films as electrodes. This device exhibits the ability to supply a power density higher than 3μWcm-2.Finally, a bio-battery prototype was tested on a sweated skin, demonstrating the potential of applicability of this bio-device as a micropower source. © 2010 Elsevier B.V.

This work analyzes the role of processing parameters on the electrical performance of GIZO (Ga2 O3: In2 O3:ZnO) films and thin-film transistors (TFTs). Parameters such as oxygen partial pressure, deposition pressure, target composition, thickness, and annealing temperature are studied. Generally, better devices are obtained when low oxygen partial pressure is used. This is related to the damage induced by oxygen ion bombardment and very high film's resistivity when higher oxygen partial pressures are used. Low deposition pressures and targets with richer indium compositions led to films with high carrier concentration, resulting in transistors with field-effect mobility as high as ∼80 cm2 Vs but poor channel conductivity modulation, becoming ineffective as switching devices. Nevertheless, it is demonstrated that reducing the GIZO thickness from 40 to 10 nm greatly enhances the switching behavior of those devices, due to the lower absolute number of free carriers and hence to their easier depletion. Annealing also proves to be crucial to control device performance, significantly modifying GIZO electrical resistivity and promoting local atomic rearrangement, being the optimal temperature determined by the as-produced films' properties. For the best-performing transistors, even with a low annealing temperature (150°C), remarkable properties such as μFE =73.9 cm2 Vs, onoff ratio≈7× 107, VT ≈0.2 V, and S=0.29 Vdec are achieved. © 2008 The Electrochemical Society.

Solution based deposition has been recently considered as a viable option for low-cost flexible electronics. In this context research efforts have been increasingly centred on the development of suitable solution-processed materials for oxide based transistors. Nevertheless, the majority of synthetic routes reported require the use of toxic organic solvents. In this work we report on a new environmental friendly solution combustion synthesis route, using ethanol as solvent, for the preparation of indium/gallium free amorphous zinc-tin oxide (ZTO) thin film transistors (TFTs) including AlOx gate dielectric. The decomposition of ZTO and AlOx precursor solutions, electrical characterization and stability of solution processed ZTO/AlOx TFTs under gate-bias stress, in both air and vacuum atmosphere, were investigated. The devices demonstrated low hysteresis (ΔV=0.23 V), close to zero turn on voltage, low threshold voltage (VT=0.36 V) and a saturation mobility of 0.8 cm2 V-1 s-1 at low operation voltages. Ethanol based ZTO/AlOx TFTs are a promising alternative for applications in disposable, low cost and environmental friendly electronics. © 2015 IOP Publishing Ltd.

This paper characterizes transparent current mirrors with n-type amorphous gallium-indium-zinc-oxide (a-GIZO) thin-film transistors (TFTs). Two-TFT current mirrors with different mirroring ratios and a cascode topology are considered. A neural model is developed based on the measured data of the TFTs and is implemented in Verilog-A; then it is used to simulate the circuits with Cadence Virtuoso Spectre simulator. The simulation outcomes are validated with the fabricated circuit response. These results show that the neural network can model TFT accurately, as well as the current mirroring ability of the TFTs. © 2005-2012 IEEE.

The degradation of thin-film transistors (TFTs) caused by the self-heating effect constitutes a problem to be solved for the next generation of displays. Aluminum nitride (AlN) is a viable alternative for gate dielectric of TFTs due to its good thermal conductivity, matching coefficient of thermal expansion to indium-gallium-zinc-oxide, and excellent stability at high temperatures. Here, AlN thin films of different thicknesses were fabricated by a low temperature reactive radio-frequency magnetron sputtering process, using a low cost, metallic Al target. Their electrical properties have been thoroughly assessed. Furthermore, the 200 nm and 500 nm thick AlN layers have been integrated as gate-dielectric in transparent TFTs with indium-gallium-zinc-oxide as channel semiconductor. Our study emphasizes the potential of AlN thin films for transparent electronics, whilst the functionality of the fabricated field-effect transistors is explored and discussed. © 2016 Elsevier B.V. All rights reserved.