Position sensitive detectors (PSD) using hydrogenated amorphous silicon as the active layer have been widely proposed either with the p-i-n or the Schottky structure. In this case, the devices are tailored to respond to light in the range 620-650 nm. Little is known about the use of silicon carbide active layers in such devices, which is important when the detected light is in the blue region of the light spectrum. In this paper we present for the first time the electro-optical properties of the a-Six:C1-x:H/Pd and p-ic-n PSD, using a-Six:C1-x:H layers deposited by plasma enhanced chemical vapour deposition (PECVD). These sensors are able to distinguish the wavelength of the impinging visible radiation (from red to blue light). In addition, the sensors respond to light intensities as lower as 1 × 10-6 W cm-2 with a resolution better than 0.04 mm and a linearity between ±0.12% and ±0.8%. © 2002 Elsevier Science B.V. All rights reserved.

In this work, we report the electro-optical properties exhibited by ZnO:A1 thin films deposited by r.f. magnetron sputtering. The effect of the deposition parameters on the properties of the films were studied with the aim to determine the most suitable deposition conditions to obtain ZnO:Al thin films with a low resistivity and high transmittance, characteristics required for applications on optoelectronic devices. After annealing, the ZnO:Al thin films present a low resistivity (6.25 × 10-3 Ωcm) and a high transmittance (90%) when produced with a deposition pressure of 1.6 × 10-2 mbar and r.f. power of 150W. © 2002 Elsevier Science Ltd. All rights reserved.

The room temperature ozone sensing properties of polycrystalline undoped zinc oxide (ZnO) thin films have been investigated. ZnO thin films have been produced by the d.c. and r.f. magnetron sputtering technique as well as with spray pyrolysis with a variety of parameters. The as-grown films were brought to a high conducting state through a reversible photoreduction process by UV light exposure and were subsequently exposed to ozone resulting in a strong resistivity increase caused by re-oxidation. The magnitude of the effect was largest for the sputtered films, which exhibited resistivity changes of more than 8 orders of magnitude, whereas films deposited by spray pyrolysis showed changes of less than 3 orders of magnitude. XRD and AFM analysis of the films revealed that all films were microcrystalline. The film texture, however, was strongly related to the growth technique and the parameters used. Best results were achieved with r.f.-sputtered films, which have been deposited at high total pressures. These films exhibited a sensor response of 1.2 × 108. © 2002 Elsevier Science B.V. All rights reserved.

In this work we studied the influence of hydrogen dilution, rf power, and the filament and substrate temperatures on the electro-optical properties and composition of a-Si:H films produced by hot wire plasma assisted technique. The a-Si:H films were produced on Mylar substrates with growth rate of up to 37 Å/s, ημτ product of 1.6 × 10-7 cm2/V, photoconductivity to dark conductivity ratio of 1 × 104 (at AM1.5 radiation), and a dark conductivity of about 10-10 (Ω cm)-1 for substrate temperature of 130 °C, hydrogen dilution of 99%, filament temperature of 1700 °C, and rf power of 100 W. © 2002 Elsevier Science B.V. All rights reserved.

The most common techniques used to produce ZnO thin films are the spray pyrolysis and the magnetron sputtering techniques, low and high cost processes respectively. The aim of this work is to compare the properties of the films produced by these two techniques. The predominant difference observed was on the morphological properties. The films produced by spray pyrolysis have a rougher surface than the ones obtained by sputtering. Also the effect of the thermal annealing treatment is much more prononnced for the ZnO thin films produced by spray pyrolysis. After heat treatment films exhibit similar electrical properties and their application to optoelectronic devices is demonstrated.

n/a

In this work we present the results of a study on the uniformity of ZnO thin films produced by spray pyrolysis. The properties of the thin films depend essentially on the carrier gas pressure and gas flow used. The best films for optoelectronic applications were obtained with a carrier gas pressure of 2 bar and solution flow of 37 ml/min. The velocity of the nozzle affects essentially the uniformity of the ZnO thin films. However this important characteristic of the large area thin films is independent of the nature (doped and undoped) of the thin film and exhibits a high dependence on the variation of the temperature along the substrate. © 2001 Materials Research Society.

The performances of amorphous and nano-crystalline porous silicon thin films as gas detector are pioneer reported in this work. The films were produced by the hot wire chemical vapour deposition (HW-CVD). These films present a porous like-structure, which is due to the uncompensated bonds and oxidise easily in the presence of air. This behaviour is a problem when the films are used for solar cells or thin film transistors. For as gas detectors, the oxidation is a benefit, since the CO, H2 or O2 molecules replace the OH adsorbed group. In the present study we observe the behaviour of amorphous and nano-crystalline porous silicon thin films under the presence of ethanol, at room temperature. The data obtained reveal a change in the current values recorded by more than three orders of magnitude, depending on the film preparation condition. This current behaviour is due to the adsorption of the OH chemical group by the Si uncompensated bonds as can be observed in the infrared spectra. Besides that, the current response and its recover time are done in few seconds.

Flexible large area thin film position sensitive detectors based on amorphous silicon technology were prepared on polyimide substrates using the conventional plasma enhanced chemical vapor deposition technique. The sensors were characterized by spectral response, illuminated I-V characteristics position detectability measurements and atomic force microscopy. The obtained one-dimensional position sensors, 5-mm wide and 60-mm long, presented a maximum spectral response at 600 nm, an open circuit voltage of 0.6 V and a position detectability with a correlation of 0.9989 associated to a S.D. of 1×10-2, comparable to those produced on glass substrates.

Coal fly ashes produced by an extinguished power plant in the north of Portugal have been melted with addition of CaCO3 and Na2CO3 to obtain glasses. One of the formulated compositions was selected for further studies and it was possible to manufacture glass-ceramics by crystallizing the parent glass through adequate time-temperature schedules. The macroscopic appearance, microstructure, mechanical, thermal and chemical properties indicated that these materials are quite attractive for cladding applications, exhibiting in some cases better performances than the conventional ceramic tiles.

In this work, we present the properties of n-type silicon films obtained by hot wire plasma assisted technique produced at different rf power and gas flow rate. The films were produced at a filament temperature of 2000°C and the rf power was varied from 0 W to 200 W while gas flow rate was varied from 15 to 100 sccm keeping rf power at 50 W. In this flow rate range, the growth rate of the films varied from 5Å/s to 250Å/s and the corresponding electrical room dark conductivity varied from 10-2 to 10(Ωcm)-1. On the other hand, we observed that the electrical conductivity increased from 2 to 6(Ωcm)-1, and the Hall mobility from 0.1 to 2 cm2/V.s as rf power change from 0 W to 200 W. The infrared, EDS and XPS analyses revealed the existence of oxygen incorporation, which is not related to post-deposition oxidation. The X-ray diffraction and μRaman data show the presence of Si crystals in the films structure and the SEM micrographs reveal a granular surface morphology with grain sizes lower than 60 nm.

In this work we present a study of the properties of ZnO thin films produced by spray pyrolysis and r.f. magnetron sputtering. Before the annealing treatment the properties of the films are very similar, which means that the films produced by both techniques could be used on optoelectronic devices. However spray pyrolysis is a more simple and cheap technique than sputtering, but with this last technique the thin films exhibit a higher uniformity. © 2001 Materials Research Society.

Thin films of SnO2 deposited by spray pyrolysis as a function of temperature and the carrier gas flow have been produced, in order to evaluate the adequate deposition parameters for application in optoelectronic devices. The characterisation was centred mainly onto the structural, electrical and optical properties of the films. The obtained results showed that the films produced at 450°C and a gas flow of 101/min (as deposited) present an average transmittance (visible spectrum) of 90% and a bulk resistivity of 3.2×10-3 Ωcm.

The purification, crystallization and identification by X-ray diffraction analysis of a horse kallikrein is reported. The protein was purired from horse seminal plasma. Crystals belong to space group C2 and the structure was solved by the MIRAS method, with two heavy-atom derivatives of mercury and platinum. X-ray diffraction data to 1.42 Angstrom resolution were collected at the ESRF synchrotron-radiation source.