Rodrigo Martins

Oxide semiconductor thin-film transistors can show anomalous behavior under bias stress. Two types of anomalies are discussed in this paper. The first is the shift in threshold voltage (VTH) in a direction opposite to the applied bias stress, and highly dependent on gate dielectric material. We attribute this to charge trapping/detrapping and charge migration within the gate dielectric. We emphasize the fundamental difference between trapping/detrapping events occurring at the semiconductor/dielectric interface and those occurring at gate/dielectric interface, and show that charge migration is essential to explain the first anomaly. We model charge migration in terms of the non-instantaneous polarization density. The second type of anomaly is negative VTH shift under high positive bias stress, with logarithmic evolution in time. This can be argued as electron-donating reactions involving H2O molecules or derived species, with a reaction rate exponentially accelerated by positive gate bias and exponentially decreased by the number of reactions already occurred. © 2016 Author(s).

ZnO films were deposited on c-plane sapphire substrates in Ar atmosphere by ii magnetron sputtering and were post-annealed at 400°C in green gas (95% N2 + 5% H2). The properties of the as-grown and annealed films have been characterized by X-ray diffraction (XRD), Rutherford backscattering (RBS), elastic recoil detection analysis (ERDA), Hall measurement and photoluminescence spectra. XRD studies confirmed the variation in strain and an improvement in crystallinity. From RBS and ERDA analysis, the presence of H atoms on the surface of the as-grown ZnO films was evidenced. Annealing in green gas increased the amount of H in the film. Compared with the as-grown films, the ultra exciting intensity obviously decreases in the annealed films and new optical active centres in the blue/violet ( 3.0 eV) and red ( 1.9) regions are emerged in the PL spectrum. The positive sign of Hall coefficient confirmed the low (-type conductivity in the as grown films, which was improved after annealing. However, the (-type conductivity was not stable, especially for the annealed sample it changes from ( type to n type after 9 days. Copyright © 2009 American Scientific Publishers All rights reserved.

This paper presents the results achieved in optimized 1D position sensitive detectors (PSD) using a metal-insulator-semiconductor (MIS) structure and different length to width ratios, in order to determine the optimal geometrical factor for the desired 3D integration. The results show that the optimized MIS PSD produced, exhibited linearity errors as low as 0.8% and sensitivities of 32 mV/cm, for a 5 mW spot beam intensity at a wavelength of 532 nm. The sensors can achieve a longitudinal spatial resolution of 1.25 μm (estimated by modulation transfer function calculation), while the transverse resolution depends on the minimum width used for each sensor. The calculated Jones parameter of the sensors is higher than 1011 J, with a fall-off parameter of 0.012 cm-1, indicating a high signal to noise detection ratio. © 2006 Elsevier B.V. All rights reserved.

In the present work, we investigate the influence of hydrocarbon (CHx) thin film coating on porous silicon (PS) by plasma enhanced chemical vapor deposition (PECVD) technique to detect CO2 gas. The fabricated CHx/PS heterojunction device shows up to one and two orders of magnitude enhancement in current under CO2 gas exposure. FTIR spectroscopy measurements reveal a remarkable structural modification of the CHx/PS device during CO2 gas exposure. Further, the enhancement of CHx related absorbance bands by a factor 6.2 for the CHx/PS specimen in comparison with PS confirm the good quality of the deposited CHx thin films. © 2007 Elsevier B.V. All rights reserved.

Molybdenum (0.5at%) doped indium oxide thin films deposited by spray pyrolysis technique were irradiated by 100MeV O 7+ ions with different fluences of 5×10 11, 1×10 12 and 1×10 13ions/cm 2. Intensity of (222) peak of the pristine film was decreased with increase in the ion fluence. Films irradiated with the maximum ion fluence of 1×10 13ions/cm 2 showed a fraction of amorphous nature. The surface microstructures on the surface of the film showed that increase in ion fluence decreases the grain size. Mobility of the pristine molybdenum doped indium oxide films was decreased from  122 to 48cm 2/Vs with increasing ion fluence. Among the irradiated films the film irradiated with the ion fluence of 5×10 11ions/cm 2 showed relatively low resistivity of 6.7×10 -4Ωcm with the mobility of 75cm 2/Vs. The average transmittance of the as-deposited IMO film is decreased from 89% to 81% due to irradiation with the fluence of 5×10 11ions/cm 2. © 2012 Elsevier Ltd.

We have deposited by Plasma Enhanced Chemical Vapour Deposition phosphorus doped amorphous and microcrystalline silicon films, as a function of the RF power (10-300 W), using a PH3/(SiH4 + H2 + He)mixture. It was found that films microcrystallization occurs for powers above 130 W, where a clear phase transition occurs. The microcrystalline films produced present high dark conductivities and optical band gaps, where the crystalline volume fraction is above 25%, as revealed by micro Raman spectroscopy. The Hall mobility have been also determined for amorphous and microcrystalline films, as a function of temperature, in the range 280-340 K. The data show that for the microcrystalline films the conduction is mainly in the extended states of the microcrystals, confirming also the double sign anomaly. That is, for n-type films, the sign is positive for the amorphous case while it is negative for the microcrystalline case. © 1998 Elsevier Science S.A.

High visible to near infrared (NIR) transparent Mo (0-1 at%) doped In2O3 (IMO) thin films with high carrier mobility were deposited on Corning-1737 glass substrates at 400 °C by spray pyrolysis experimental technique. The films were annealed in vacuum (∼1×10-4 mbar) at 550 °C for 45 min. XRD analysis confirmed that indium oxide belongs to cubic bixbyite structure. The preferred growth orientation along (2 2 2) plane for low Mo doping level shifts to (4 0 0) for higher Mo doping levels. Crystallite sizes extracted from the XRD data corroborate the changes in full-width at half-maximum due to the variation in Mo doping. Scanning electron microscopy study illustrates the evolution in surface microstructures as a function of Mo doping. The negative sign of Hall coefficient confirmed n-type conductivity. Films with high mobility of ∼149 cm2/(V s), carrier concentration of ∼1.0×1020 cm-3, resistivity of ∼4.0×10-4 Ω cm and high figure of merit of ∼1.02×10-2 Ω-1 were observed for post-annealed films (0.5 at% Mo). The obtained high average transparency of ∼83% in the wavelength range 400-2500 nm confirms that transmittance is well extended into the NIR region. © 2009 Elsevier B.V. All rights reserved.

This work presents for the first time a study on the deposition of polymorphous silicon at an excitation frequency of 27.12 MHz in a large-area plasma enhanced chemical vapor deposition (PECVD) reactor. Moreover, the films produced at 13.56 MHz were also investigated to compare their performance with that of the films produced at 27.12 MHz. The SiH4/H2 plasma was characterized by impedance probe measurements, aiming to identify the plasma conditions that lead to produce polymorphous films, under quasi-isothermal conditions. The films were characterized by spectroscopic ellipsometry, infrared absorption, Raman spectroscopy, and hydrogen exodiffusion experiments. These techniques enable a detailed structural characterization of the polymorphous films and a study of the differences between the films deposited at 27.12 MHz and 13.56 MHz. Conductivity measurements were also performed to determine the transport properties of the films. The results show that by using a 27.12 MHz frequency, the growth rate increased by 70% and a more stable, relaxed and denser structure was obtained.

Large area thin film position sensitive detectors based on amorphous silicon technology have been prepared on polyimide substrates using the conventional plasma enhanced chemical vapour deposition technique. The sensors have been characterised by spectral response, illuminated I-V characteristics and position detectability measurements. The obtained one dimensional position sensors with 5 mm wide and 60 mm long present a maximum spectral response at 600 nm, an open circuit voltage of 0.6 V° and a position detectability with a correlation of 0.9989 associated to a standard deviation of 1 × 10-2, comparable to those ones produced on glass substrates. The surface of the sensors at each stage of fabrication was investigated by Atomic Force Microscopy.

In recent works large area hydrogenated amorphous silicon p-i-n structures with low conductivity doped layers were proposed as single element image sensors. The working principle of this type of sensor is based on the modulation, by the local illumination conditions, of the photocurrent generated by a light beam scanning the active area of the device. In order to evaluate the sensor capabilities is necessary to perform a response time characterization. This work focuses on the transient response of such sensor and on the influence of the carbon contents of the doped layers. In order to evaluate the response time a set of devices with different percentage of carbon incorporation in the doped layers is analyzed by measuring the scanner-induced photocurrent under different bias conditions. © 2004 Elsevier B.V. All rights reserved.

We have developed a rectangular dual-axis large area Position Sensitive Detector (PSD), with 5 cm×5 cm detection area, based on PIN hydrogenated amorphous silicon (a-Si:H) technology, produced by Plasma Enhanced Chemical Vapor Deposition (PECVD). The metal contacts are located in the four edges of the detected area, two of them located on the back side of the ITO/PIN/Al structure and the others two located in the front side. The key factors of the detectors resolution and linearity are the thickness uniformity of the different layers, the geometry and the contacts location. Besides that, edge effects on the sensor's corner disturb the linearity of the detector. In this paper we present results concerning the linearity of the detector as well as its optoelectronic characteristics and the role of the i-layer thickness on the final sensor performances.

The aim of this work is to present the main optoelectronic characteristics of large-area one-dimensional position-sensitive detectors (1D TFPSDs) based on amorphous silicon (a-Si) p-i-n diodes. From that, the device resolution, response time and detectivity (defined as being the reciprocal of the noise equivalent power pattern) are derived and discussed concerning the field of applications of the 1D TFPSDs. © 1996.

The role of the deposition pressure and hydrogen dilution in the production of p-type Si:H films by hot wire chemical vapor deposition, was investigated. The system used permits to obtain uniform and homogeneous films properties over a 10cm×10cm substrate area. As heated filament we used Ta, since Ta filaments have longer life period without deteriorating than the W filaments ones. In this work, we show that the electrical properties of the films produced are dependent on the process gas pressure. In the pressure range of 13.3 Pa (0.1 Torr) to 66.5 Pa (0.5Torr), the film's coplanar electrical conductivity at room temperature varies by more than two orders of magnitude, for films produced at same hydrogen dilution and filament temperature, reaching values of about 0.1 (Ωcm)-1, at deposition pressures of about 40-53Pa (0.3-0.4Torr). On the other hand, the increase in hydrogen dilution (from 87% to 96%) promotes the surface roughness due to an enlargement of grain sizes in the direction of the {220} diffraction planes as observed by SEM micrographs without changing the crystalline fraction (48-50%) obtained by micro-Raman analysis.

The laser scanned photodiode (LSP) presents a new concept of image sensor with application in fields where low cost, large area and design simplicity are of major importance. Over the past few years this type of sensor has been under investigation and development, where several structures have been tested and characterized. In this work we present the physical explanation of device operating principle, with recourse to numerical simulation applied to structures with different compositions of the doped layers. An electrical model for this type of device is presented, enabling a fast evaluation of the device characteristics by means of an electrical simulation program. © 2006 Elsevier B.V. All rights reserved.

The objective of this work is to provide a basis for the interpretation of the a-Si:H photodiode behaviour under low illumination level conditions, where a lateral leakage current plays an important role on the devices' performances when the doped collecting layer can not be considered a true equipotential. To determine this effect, a-Si:H p.i.n devices with small metal dot contacts, matrix distributed, were produced and analysed before and after etching the surrounding doped region of the metal collecting contact. The experimental data fit a model that includes the contribution of a lateral leakage current influencing the J-V characteristics, responsivity and the apparent light degradation behaviour of the device.

The aim of this work is to provide the basis for the interpretation, under steady state conditions, of the lateral photoeffect in p-i-n a-Si:H one-dimensional thin-film position-sensitive detectors (1D TFPSD) and the determination of its linear spatial detection limits, function of the device, and light spot source characteristics. This leads to the development of a model, based on the application of the Poisson, continuity, and current density equations in the p-i-n junction, where two thin resistive layers, as equipotentials, are considered on both sides of the doped layers. The experimental data recorded in 1D TFPSD devices with different performances are compared with the predicted curves and the obtained correlations discussed. © 1995 American Institute of Physics.

We report experimental data on light soaking of a-Si: H solar cells as well as the role played by the temperature on the metastable light-induced defect growth. We studied the temperature and intensity dependence on the photoconductivity, μτ product and density of states at the Fermi level (g(Ef)) and we found that the rate of defect growth on the i-layer depends on the quality of the material and on the annealing temperature, resulting from an equilibrium between light-induced and light-annealed defects. The photoresponse of the devices is mainly ruled by its microstructure, and depends on the fraction of hydrogen bounded on internal surfaces. Results suggest a correlation between the decrease of μτ product for electron and the increase of the fraction of hydrogen bonded on internal surfaces, suggesting structural changes during the degradation process. Data show, also, that the thermal annealing effect is worthless up to 70°C because of light-induced defect-generation being the dominant process in recombination mechanisms. © 1994.

We present the modelling of a new two-terminal and low-voltage operating optoelectronic device based on MIS silicon structure with multichannel insulator and having as gate a transparent metallic tin-doped indium oxide (ITO) layer deposited by spray pyrolysis technique over the insulator layer. ITO layer has a multiple non-rectifier electrical contact with silicon substrate, in the SiO2 channel's region. Construction details of the process, together with its operating characteristics are given. The devices developed do not require external active electronic components (transistors, microschemes) to execute their functions and to transform analogue input optical signals to digital output form, highly important for a wide range of optoelectronic applications.

A linear array thin film position sensitive detector (LTFPSD) based on hydrogenated amorphous silicon (a-Si:H) is proposed for the first time. Taking advantage of the optical properties presented by a-Si:H devices, we have developed a LTFPSD with 128 integrated elements able to be used in 3D inspections/measurements. Each element consists of a one-dimensional LTFPSD, based on a p-i-n diode produced in a conventional PECVD system, where the doped layers are coated with thin resistive layers to establish the required device equipotentials. By proper incorporation of the LTFPSD into an optical inspection camera it will be possible to acquire information about an object/surface, through the optical cross-section method. The main advantages of this system, when compared with the conventional CCDs, are the low complexity of hardware and software used and that the information can be continuously processed (analog detection). © 1995 American Institute of Physics.

A novel compact linear thin film position sensitive detector with 128 elements, based on p-i-n a-Si:H devices was developed. The proper incorporation of this sensor into an optical inspection camera makes possible the acquisition of three dimension information of an object, using laser triangulation methods. The main advantages of this system, when compared with the conventional charge-coupled devices, are the low complexity of hardware and software used and that the information can be continuously processed (analogue detection).

A linear array thin film position sensitive detector (LTFPSD) based on hydrogenated amorphous silicon (a-Si:H) is proposed for the first time, taking advantage of the optical properties presented by a-Si:H devices we have developed a LTFPSD with 128 integrated elements able to be used in 3-D inspections/measurements. Each element consists on a one-dimensional LTFPSD, based on a p.i.n. diode produced in a conventional PECVD system, where the doped layers are coated with thin resistive layers to establish the required device equipotentials. By proper incorporation of the LTFPSD into an optical inspection camera it is possible to acquire information about an object/surface, through the optical cross-section method. The main advantages of this system, when compared with the conventional CCDs, are the low complexity of hardware and software used and that the information can be continuously processed (analogue detection).

The linearity and sensitivity of linear Position Sensitive Detectors (PSD) are the two principal characteristics of sensors to be optimised in sensor fabrication. This work presents several efforts made to understand the internal and external parameters that influence the linearity and sensitivity of Metal Insulator Semiconductor (MIS) linear PSD with an active length of 6 cm. The use of long sensitive areas allows the PSD to achieve greater resolution without the need of a highly accurate light spot integration mechanism. The PSD is built in a multi-layered structure consisting of Cr/a-Si:H (n+ doped)/a-Si:H (intrinsic)/SiOx (passivation layer)/Au, where the active a-Si:H layers were deposited by Modified Triode Plasma Enhanced Chemical Vapour Deposition (MTPECVD), which allows the deposition of good electronic grade material with a low (≈ 1 × 1015 cm-3) defect density inferred by CPM. The sensor linearity and sensitivity shows dependence on the sensor width to length ratio, SiOx layer and on the value of the load resistance. Sensitivities of more than 30 mV/cm were achieved with linearity near 99%. Besides that, this type of MIS structure allows an improved spectral response in the near-UV region and has its maximum response at 540 nm. © 2005 Springer Science + Business Media, Inc.

In this work, it is demonstrated the application of a high k dielectric, as hafnium oxide (HfO2), in poly-Si thin film transistors (TFTs) obtained by metal induced lateral crystallization (MILC). The dielectric layer was deposited at room temperature by sputtering, using argon and oxygen as process gases. As produced TFTs exhibit field effect mobility around 45 cm2 V-1 s-1and Ion/Ioff ratio of about 2 × 105. After annealing in a forming gas atmosphere for about 1 h at 200 °C, the threshold voltage and the sub-threshold slope are reduced, respectively from 4.8 to 2 V and from 1.6 to 1.4 V/dec. Nevertheless, by doing so, we notice a reduction on the field effect mobility of about 45% and a decrease of about 2.5 times on the Ion/Ioff ratio. Longer annealing time will not improve the TFT's performance. © 2008 Elsevier B.V. All rights reserved.

In this work hafnium oxide (HfO2) was deposited by r.f. magnetron sputtering at room temperature and then annealed at 200 °C in forming gas (N2+H2) and oxygen atmospheres, respectively for 2, 5 and 10 h. After 2 h annealing in forming gas an improvement in the interface properties occurs with the associated flat band voltage changing from -2.23 to -1.28 V. This means a reduction in the oxide charge density from 1.33×1012 to 7.62×1011 cm-2. After 5 h annealing only the dielectric constant improves due to densification of the film. Finally, after 10 h annealing we notice a degradation of the electrical film's properties, with the flat band voltage and fixed charge density being -2.96 V and 1.64×1012 cm-2, respectively. Besides that, the leakage current also increases due to crystallization. On the other hand, by depositing the films at 200 °C or annealing it in an oxidizing atmosphere no improvements are observed when comparing these data to the ones obtained by annealing the films in forming gas. Here the flat band voltage is more negative and the hysteresis on the C-V plot is larger than the one recorded on films annealed in forming gas, meaning a degradation of the interfacial properties. © 2006 Elsevier Ltd. All rights reserved.

We have investigated the electrical properties of metal-semiconductor field-effect transistors (MESFET) based on amorphous oxide semiconductor channels. All functional parts of the devices were sputter-deposited at room temperature. The influence on the electrical properties of a 150 °C annealing step of the gallium-indium-zinc-oxide channel is investigated. The MESFET technology offers a simple route for processing of the transistors with excellent electrical properties such as low subthreshold swing of 112 mV/decade, gate sweep voltages of 2.5 V, and channel mobilities up to 15 cm2 /V s. © 2010 American Institute of Physics.