Rodrigo Martins

This work deals with the study of the role of intra-gap density of states on the colour selection of the collection spectrum of glass/ITO/a-Six:C1-x:H/Al Schottky photodiodes. In order to optimise the voltage colour selection and to study the influence of intragap density of states in the final device performances, different undoped a-Six:C1-x:H films (1 μm thick) have been produced in a conventional Plasma Enhanced Chemical Vapour Deposition (PECVD) system using silane and a controlled mixtures of silane and methane as gas sources. The properties of the films were analysed by dark conductivity measurements, infrared spectroscopy, visible spectroscopy and constant photocurrent method (CPM), to determine the valence controllability and to correlate the silicon carbide layer composition with the performances of the devices. The performances obtained concerning the spectral response of the devices were correlated with the carbon content and the density of states of the a-Six:C1-x:H films.

The aim of this work is to study the role of hydrogen dilution and filament temperature on the properties of nanocrystalline silicon thin films (undoped and doped) produced by the hot wire technique. These deposition parameters are correlated to the film's structure, composition and electro-optical properties with special emphasis on boron doped nanocrystalline silicon carbide reported here. © 1998 Elsevier Science B.V. All rights reserved.

The objective of this work is to present an analytical model able to interpret the experimental dependence of the uniformity of films produced by the plasma-enhanced chemical vapour deposition technique on the deposition parameters (discharge pressure, gas flow temperature and rf power density). The model proposed is based on the Navier-Stokes equations applied to a gas flow considered to be quasi-incompressible and quasi-inviscous, whenever the Mach number is below 0·3. This condition leads to the establishment of the proper quasisteady-state gas flow equations, and the corresponding equations of energy and momentum balance ascribed to the mass profile of the species formed, under the presence of a low-rf-power plasma density, are able to predict the uniformity distribution of the film over the entire deposited substrate area.

The aim of this work is to present an analytical model able to interpret the experimental data of the dependence of film's uniformity on the discharge pressure, gas flow and temperature used during the production of thin films by the plasma enhancement chemical vapour deposition technique, under optimised electrode's geometry and electric field distribution. To do so, the gas flow is considered to be quasi-incompressible and inviscous leading to the establishment of the electro-fluid-mechanics equations able to interpret the film's uniformity over the substrate area, when the discharge process takes place in the low power regime.

This paper reports results on the role of high hydrogen dilution (above 80%) on the electro-optical and structural properties of boron doped silicon films produced by hot wire chemical vapor deposition (HW-CVD) technique, keeping constant the filament temperature. The structural, compositional, morphological, electrical and optical properties achieved show that the films present excellent homogeneity over the entire 10 x 10 cm deposited area. These results were obtained for films produced at gas pressures below 66.5 Pa, in spite of the high flow rate used. © 2001 Elsevier Science B.V. All rights reserved.

This paper deals with the study of the role of gas temperature and of the ratio of r.f. power to gas flow on the particle’s formation in amorphous silicon films grown by plasma enhanced chemical vapour deposition technique, by monitoring the plasma impedance behaviour under different process conditions. The aim is to determine in which conditions the particles formed do not deteriorate the performances of the films grown or even can lead to an improvement of the properties of the films deposited. The results achieved show the existence of two main boundary regions (β- and θ-regions) separating the so-called α-regime (no powder formed) from the γ-regime (powder formed). Those regions are reached either by heating the gas, changing the gas pressure or using high power to gas flow ratios. In the β-region the probability of incorporating nanoparticles in the films is low and the films exhibit properties similar to those of the ones grown in the α-regime, with a low density of voids incorporated. In the θ-region small nanoparticles can be incorporated leading to films with density of states below 5×1015 cm-3, widened Urbach energies and photosensitivities about two orders of magnitude larger than that of conventional amorphous silicon grown in the α-regime. © 2000 Elsevier Science Ltd.

This paper deals with the study of the role of gas temperature and of the ratio of r.f. power to gas flow on the particle's formation in amorphous silicon films grown by the plasma enhanced chemical vapour deposition technique, by monitoring the plasma impedance behaviour under different process conditions. The results achieved show the existence of two main boundary regions separating the so-called α-regime (no powder formed) from the γ-regime (powder formed). Those regions are reached either by heating the gas, changing the gas pressure or using high power to gas flow ratios, corresponding to the establishment of a balance between the plasma resistance and the plasma reactance. In the β-region the probability to incorporate nanoparticles in the films is low and the films exhibit photosensitivity's of about 105 with density of states determined by the constant photocurrent method below 6×1015 cm-3 with Urbach energies below 50 meV. In the θ-region small nanoparticles can be incorporated leading to films with density of states below 3×1015 cm-3, with Urbach energies above 50 meV and photosensitivity's above 106, about two orders of magnitude larger than that of conventional amorphous silicon grown in the α-regime.

Nanocrystalline p-doped silicon films were deposited at low substrate temperatures (around 200°C) in a hot wire reactor. In this paper we present the results on the role of the hydrogen dilution and filament temperature on the film's structure, composition, morphology and transport properties. The film's structure changes from honeycomb-like to a granular needle shape as the filament temperature changes from about 2000°C and hydrogen dilution 87%, to values above 2100°C and hydrogen dilution 90%, respectively. The nanocrystalline silicon-based films produced have optical gaps varying from 1.6 to 1.95 eV, with conductivities up to 0.2 S cm-1 and grain sizes (obtained by X-ray diffraction) in the range of 10-30 nm. © 1999 Elsevier Science B.V. All rights reserved.

In this work, we study the influence of the hydrogenated amorphous silicon (a-Si:H) surface treatment on the J-V characteristics of a-Si:H/Pd Schottky barrier photodiodes. The a-Si:H surface were etched, thermally oxidised and wet oxidised by H2O2. The a-Si:H films were characterised by spectroscopic ellipsometry, were we found that all the oxidation techniques promote an increase of the surface oxide thickness that was confirmed by the increase of the barrier height. The highest barrier was achieved by the H2O2 oxidation where a value of 1.17 eV was found. As a result of the barrier height increase, the dark reverse current density decreases up to 10-10 A/cm2 and the signal to noise ratio increases up to 106. The open circuit voltage under AM1.5 illumination conditions also increases from 0.4 to 0.5 V. These results reveal the importance of the a-Si:H surface preparation prior to metallization to improve the Schottky photodiodes properties. © 2002 Elsevier Science B.V. All rights reserved.

In this work we present the current/voltage characteristics of Si:H/Pd Schottky structures using high quality, low defect density amorphous silicon (a-Si:H) deposited by a non-conventional, modified triode PECVD method. This new configuration allows the deposition of compact and high quality a-Si:H with a photosensitivity of 107, yielding films with low bulk defects. AFM measurements also revealed that these films have a very smooth surface allowing a low defect interface between the metal and the a-Si:H. As a result, we show that by using these a-Si:H films and by proper control of the i-layer thickness the reverse dark current of the diode can be highly reduced achieving signal to noise ratio of 106, surpassing the results usually achieved by p-i-n structures.

The aim of this work is to interpret the role of the lateral leakage current on the a-Si:H solar cell performances (J-V characteristics, responsivity and the apparent device degradation behaviour), under low illumination conditions.

In this work we present results of studies performed on Schottky and metal-insulator-semiconductor (MIS) position sensitive detectors (PSD) structures: substrate (glass)/ Cr (300 nm) / a-Si:H [n] (37 nm) / a-Si:H [i] (600 nm) / SiO2 (1.5 nm - for the MIS) / Au (7 nm). The effect of the interfacial oxide layer between Au and a-Si:H, for the MIS structures, was studied and compared with the Schottky, in order to determine how beneficial it could be for device performances and time degradation. For doing so, the Au thickness of 70Å was deposited by thermal evaporation on an oxide free (Schottky) and oxidized (≈20Å) (MIS) a-Si:H surfaces. These structures were characterized by SIMS, RBS, SEM and AFM in order to correlate the obtained diffusion profile of Au at the interface and the topography with the presence of the oxide at the interface. The results show that the Au inter-diffuses very easily in the oxide free a-Si:H surface, even at room temperature, degrading the devices performance. On the other hand, the MIS structures, with their interfacial oxide present no structural changes after annealing and the PSD produced are stable. We believe that this effect is associated with the barrier effect of the interfacial oxide that prevents the Au diffusion. The optimized 1D MIS sensors are stable and exhibit a linearity error as low as 0.8 % and sensitivities of 33 mV/cm for a 5 mW spot beam intensity at a wavelength of 532 nm, while the Schottky sensors showed a time degradation of their characteristics. © 2006 Materials Research Society.

The aim of this work is to present an analytical model which can to interpret the role of the collecting resistive layer on the static performances exhibited by 2D amorphous silicon hydrogenated p-i-n thin film position sensitive detectors. In addition, experimental results concerning the device linearity and spatial resolution are presented and checked against the predicted values of the analytical model proposed. © 1999 Elsevier Science S.A. All rights reserved.

In this work we present results of structural composition and morphological characteristics of polymorphous silicon (pm-Si:H) films deposited by PECVD at 13.56 and 27.12 MHz. In addition, the role of the excitation frequency on the growth rate will be also analyzed. The results show that by using the 27.12 MHz excitation frequency the hydrogen dilution in the plasma needed to produce pm-Si:H can be reduced by more than 50% as well as the rf power density, leading to an increase on the growth rate to values higher than 3 Å/s. Spectroscopic ellipsometry and Raman spectroscopy show that the 27.12 MHz pm-Si:H films are more ordered than the pm-Si:H films produced at 13.56 MHz, while the infrared spectroscopy show that the SiH2 concentration in the films is strongly reduced. AFM measurements reveal that the films produced at 27.12 MHz films are more structured, presenting also higher roughness. © 2004 Elsevier B.V. All rights reserved.

In this paper we present the effect of thickness on the electrical and optical properties of intrinsic/nondoped zinc oxide thin films deposited at room temperature by radio frequency magnetron sputtering, able to be used as a semiconductor material on electronic devices, like for example ozone gas sensors and ultraviolet detectors. These films are polycrystalline with a c-axis preferential orientation parallel to the substrate. The films present a resistivity that varies from 5.0 × 104 Ω cm to 1.0 × 109 Ω cm with an optical visible transmittance of 85%. The sensor response exceeds more than five orders of magnitude when exposed to UV light recovering to the initial state in the presence of ozone. © 2006 Elsevier B.V. All rights reserved.

Trimethylboron (TMB) has been receiving attention as a valid alternative to diborane and methane mixtures for the deposition of p-type silicon films for applications in optoelectronic devices such as solar cells. In this paper we report on p-type hydrogenated nanocrystalline silicon carbide (nc-Si:C:H) films produced by standard 13.56 MHz plasma enhanced chemical vapour deposition technique, using TMB as gas source, under high hydrogen dilution (98%) and using high deposition pressures (3 Torr). The films obtained were characterized by spectroscopic ellipsometry (SE), Raman spectroscopy (RS), and electrical measurements to determine their optical, structural and electrical properties. We achieved conductivities as high as 8.3 (Ω cm) -1, one of the highest values of conductivity published to date using TMB with standard rf-PECVD. Spectroscopic ellipsometry modeling revealed that the films growth mechanism proceeds through a sub-surface layer mechanism that leads to the formation of nanocrystalline silicon. Copyright © 2010 American Scientific Publishers All rights reserved.

This paper studies the dc and ac impedance behaviour of undoped ZnO thin films produced by spray pyrolysis and rf magnetron sputtering under UV light illumination, at room temperature, emphasising the role that the crystallite size, structure, surface morphology and the state of surface have on the electrical responsivities obtained. The results achieved show that the sputtered films with crystal sizes of about 4 nm exhibit dc electrical UV responsivities of 108. On the other hand, the spray pyrolysis films exhibit the lowest dc responsivities, due the high crystal sizes and state of surface contamination, to which very good capacitance responses were obtained, mainly due to the degree of porosity exhibit by these films when produced at low temperatures. Based on that, a two-phase electrical model is proposed to explain the set of behaviours observed. © 2005 Elsevier B.V. All rights reserved.

Hafnium oxide-aluminum oxide (HfAlO) dielectric films were cosputtered using HfO2 and Al2 O3 targets, and their properties are studied in comparison with pure HfO2 films. The X-ray diffraction studies confirmed that the HfO2 films are nanocrystalline with a monoclinic phase. The as-deposited HfAlO films with a chemical composition of (HfO2) 0.86 (Al2 O3) 0.14 are amorphous even after annealing at 500°C. Further, the cosputtered films show a slight reduction in leakage current. The leakage current density may be significantly reduced below 3× 10-10 A cm-2 at an electric field of 0.25 MV/cm when applying the proper radio-frequency bias to the substrate. © 2009 The Electrochemical Society.