Rodrigo Martins

In this work we present the current/voltage characteristics of Si:H/Pd Schottky structures using high quality, low defect density amorphous silicon (a-Si:H) deposited by a non-conventional, modified triode PECVD method. This new configuration allows the deposition of compact and high quality a-Si:H with a photosensitivity of 107, yielding films with low bulk defects. AFM measurements also revealed that these films have a very smooth surface allowing a low defect interface between the metal and the a-Si:H. As a result, we show that by using these a-Si:H films and by proper control of the i-layer thickness the reverse dark current of the diode can be highly reduced achieving signal to noise ratio of 106, surpassing the results usually achieved by p-i-n structures.

The aim of this paper was to present results of the role of the d.c. grid bias on the silane plasma impedance and its I-V characteristics to grow undoped amorphous silicon (a-Si:H) films by plasma enhanced chemical vapour deposition (PECVD) in conditions where some nanoparticles can be formed in the growth region of the deposition process, under proper ion bombardment. The results achieved show that the performances of the films produced are dependent on the self bias voltage that can present photosensitivities of approximately 107 (two orders of magnitude larger than the one exhibited by films grown under conventional conditions) with density of states determined by the constant photocurrent method below 4×1015 cm-3. Apart from that, the films grown are less affected by light soaking than the conventional films.

This paper reports results on the role of high hydrogen dilution (above 80%) on the electro-optical and structural properties of boron doped silicon films produced by hot wire chemical vapor deposition (HW-CVD) technique, keeping constant the filament temperature. The structural, compositional, morphological, electrical and optical properties achieved show that the films present excellent homogeneity over the entire 10 x 10 cm deposited area. These results were obtained for films produced at gas pressures below 66.5 Pa, in spite of the high flow rate used. © 2001 Elsevier Science B.V. All rights reserved.

In this work we present a study of influence of ion bombardment on the optical, electrical and compositional properties of the intrinsic amorphous silicon films deposited in a modified triode plasma-enhanced chemical vapour deposition (PECVD) reactor. The application of a DC voltage to a grid placed in front of the r.f. electrode allowed us to control the energy and polarity of the ions striking the substrate during film growth. The results show a variation by two orders of magnitude in the dark conductivity from 10-10 to 6.2 × 10-12 (Ω cm)-1, while the photosensitivity varied from 2 × 105 to 2 × 107. A process plasma that takes place in the γ-type regime was associated with the use of a negative bias, while a process plasma like the one of the α-type regime was associated with the use of a positive bias. The films deposited with a bias ≈ 38 V are highly intrinsic and the abrupt change in the conductivity properties observed at this bias is attributed to a change in the density of the states ascribed to the position of the Fermi level. That is, a precise control of the energy of the ions striking the substrate during the film growth leads to improved film optoelectronic properties, very important for device applications. © 2001 Elsevier Science Ltd. All rights reserved.

The effects of Sn thickness electrodeposited over Cu on the structural and morphological performance of the joints formed were investigated. The electrical stability of the joints formed was analyzed under extreme aggressive conditions. Results indicated that the proposed soldering technology greatly satisfied the demands concerning soldering specifications.

This paper deals with the study of the role of gas temperature and of the ratio of r.f. power to gas flow on the particle’s formation in amorphous silicon films grown by plasma enhanced chemical vapour deposition technique, by monitoring the plasma impedance behaviour under different process conditions. The aim is to determine in which conditions the particles formed do not deteriorate the performances of the films grown or even can lead to an improvement of the properties of the films deposited. The results achieved show the existence of two main boundary regions (β- and θ-regions) separating the so-called α-regime (no powder formed) from the γ-regime (powder formed). Those regions are reached either by heating the gas, changing the gas pressure or using high power to gas flow ratios. In the β-region the probability of incorporating nanoparticles in the films is low and the films exhibit properties similar to those of the ones grown in the α-regime, with a low density of voids incorporated. In the θ-region small nanoparticles can be incorporated leading to films with density of states below 5×1015 cm-3, widened Urbach energies and photosensitivities about two orders of magnitude larger than that of conventional amorphous silicon grown in the α-regime. © 2000 Elsevier Science Ltd.

This paper deals with the study of the role of gas temperature and of the ratio of r.f. power to gas flow on the particle's formation in amorphous silicon films grown by the plasma enhanced chemical vapour deposition technique, by monitoring the plasma impedance behaviour under different process conditions. The results achieved show the existence of two main boundary regions separating the so-called α-regime (no powder formed) from the γ-regime (powder formed). Those regions are reached either by heating the gas, changing the gas pressure or using high power to gas flow ratios, corresponding to the establishment of a balance between the plasma resistance and the plasma reactance. In the β-region the probability to incorporate nanoparticles in the films is low and the films exhibit photosensitivity's of about 105 with density of states determined by the constant photocurrent method below 6×1015 cm-3 with Urbach energies below 50 meV. In the θ-region small nanoparticles can be incorporated leading to films with density of states below 3×1015 cm-3, with Urbach energies above 50 meV and photosensitivity's above 106, about two orders of magnitude larger than that of conventional amorphous silicon grown in the α-regime.

The aim of this work is to present an analytical model able to interpret the role of the thin collecting resistive layer on the static performances exhibited by 2D amorphous silicon hydrogenated pin thin film position sensitive detectors. In addition, experimental results concerning the device linearity and spatial resolution are presented and checked against the predicted values of the analytical model proposed.

Nanocrystalline p-doped silicon films were deposited at low substrate temperatures (around 200°C) in a hot wire reactor. In this paper we present the results on the role of the hydrogen dilution and filament temperature on the film's structure, composition, morphology and transport properties. The film's structure changes from honeycomb-like to a granular needle shape as the filament temperature changes from about 2000°C and hydrogen dilution 87%, to values above 2100°C and hydrogen dilution 90%, respectively. The nanocrystalline silicon-based films produced have optical gaps varying from 1.6 to 1.95 eV, with conductivities up to 0.2 S cm-1 and grain sizes (obtained by X-ray diffraction) in the range of 10-30 nm. © 1999 Elsevier Science B.V. All rights reserved.

The aim of this work is to present an analytical model which can to interpret the role of the collecting resistive layer on the static performances exhibited by 2D amorphous silicon hydrogenated p-i-n thin film position sensitive detectors. In addition, experimental results concerning the device linearity and spatial resolution are presented and checked against the predicted values of the analytical model proposed. © 1999 Elsevier Science S.A. All rights reserved.

The aim of this work is to study the role of hydrogen dilution and filament temperature on the properties of nanocrystalline silicon thin films (undoped and doped) produced by the hot wire technique. These deposition parameters are correlated to the film's structure, composition and electro-optical properties with special emphasis on boron doped nanocrystalline silicon carbide reported here. © 1998 Elsevier Science B.V. All rights reserved.

The objective of this work is to present an analytical model able to interpret the experimental dependence of the uniformity of films produced by the plasma-enhanced chemical vapour deposition technique on the deposition parameters (discharge pressure, gas flow temperature and rf power density). The model proposed is based on the Navier-Stokes equations applied to a gas flow considered to be quasi-incompressible and quasi-inviscous, whenever the Mach number is below 0·3. This condition leads to the establishment of the proper quasisteady-state gas flow equations, and the corresponding equations of energy and momentum balance ascribed to the mass profile of the species formed, under the presence of a low-rf-power plasma density, are able to predict the uniformity distribution of the film over the entire deposited substrate area.

The aim of this work is to present an analytical model able to interpret the experimental data of the dependence of film's uniformity on the discharge pressure, gas flow and temperature used during the production of thin films by the plasma enhancement chemical vapour deposition technique, under optimised electrode's geometry and electric field distribution. To do so, the gas flow is considered to be quasi-incompressible and inviscous leading to the establishment of the electro-fluid-mechanics equations able to interpret the film's uniformity over the substrate area, when the discharge process takes place in the low power regime.

The aim of this work is to present an analytical model able to interpret the role of the thin collecting resistive layer on the static performances exhibited by 1D amorphous silicon hydrogenated p-i-n thin film position sensitive detectors. The data obtained show that the devices present a linearity and a spatial resolution, of respectively, better than 99% and 20 μm for a spatial detection limit of about 80 mm, highly dependent on the characteristics exhibited by the collecting resistive layer that should have sheet resistivities in the range of 10 to 103 Ω/sq, as predicted by the model proposed. © 1996 American Institute of Physics.

The aim of this work is to present experimental data concerning the role of the oxygen partial pressure during the production process on the properties (structure, morphology, composition, and transport properties) exhibited by doped microcrystalline silicon oxycarbide films. The films were produced by a two consecutive decomposition and deposition chamber system, where a spatial separation between the plasma and the growth regions is achieved. The films produced by this technique are highly conductive and highly transparent with suitable properties for optoelectronic applications requiring wide band-gap and low-conductivity materials. © 1995, American Vacuum Society. All rights reserved.

The aim of this work is to interpret the role of the lateral leakage current on the a-Si:H solar cell performances (J-V characteristics, responsivity and the apparent device degradation behaviour), under low illumination conditions.

PIN solar cells were light soaked up to 60 hours. The cell characteristics, the optoelectronic properties and the microstructure parameter (R = I2100/I2100+I2000) as well as the hydrogen content (CH) and density of states (g(Ef)) of the active i-layer were monitored throughout the entire light induced degradation process and compared with the correspondents μτ product (for both carriers) inferred through steady photoconductivity and FST measurements. Data show a strong correlation between the decrease of μτ product for electron and the increase of the fraction of hydrogen bonded on internal surfaces (R increases from 0.1 to 0.4) suggesting structural changes during the light induced defects' formation. For holes, the μτ product remains approximately constant and only dependent on the initial hydrogen content. As g(Ef) increases, μτ presents an asymmetrical decrease showing that electrons are more sensitive to defects' growth than holes. We also observe that the rate of degradation is faster for samples having the lowest defect densities, R and CH, showing that the amount of degradation is not a simple function of the photon exposure (Gt product) but also depends on the material microstructure.

Amorphous Silicon solar cells have been produced by a two consecutive decomposition and deposition chamber system, using polished S. S. substrates. Through a systematic investigation of the electrical and optical properties of doped and undoped amorphous silicon layers (1) we observe that the deposition conditions (gas partial pressure, density of r. f. power, substrate temperature, electromagnetic static fields applied to the substrate, and gas flow rate) influence films properties. In the course of this investigation we have been studying the role of the sheet resistance, R//s, of the I. T. O. layer on the short circuit current, I//s//c, and on the open circuit voltage, V//o//c, of p. i. n. structures of 16cm**2 in area. The obtained results indicate that V//o//c is almost independent on R//s, while I//s//c variation approaches a square root dependence on R//s.