Rodrigo Martins

Indium molybdenum oxide thin films were RF sputtered at room temperature on glass substrates with a reference base pressure of 7.5 × 10- 4 Pa. The electrical and optical properties of the films were studied as a function of oxygen partial pressures (OPP) ranging from 1.5 × 10- 3 Pa to 3.5 × 10- 3 Pa. The obtained data show that the bulk resistivity of the films increased by about 4 orders of magnitude (from 7.9 × 10- 3 to 7.6 × 101 Ω-cm) when the OPP increased from 1.5 × 10-3 to 3.5 × 10- 3 Pa, and the carrier concentration decreased by about 4 orders (from 1.77 × 1020 to 2.31 × 1016 cm- 3). On the other hand, the average visible transmittance of 30.54% of the films (brown colour; OPP = 1.5 × 10- 3 Pa) was increased with increasing OPP to a maximum of 80.47% (OPP = 3.5 × 10- 3 Pa). The optical band gap calculated from the absorption edge of the transmittance spectra ranges from 3.77 to 3.88 eV. Further, the optical and electrical properties of the films differ from those deposited at similar conditions but with a base pressure lower than 7.5 × 10- 4 Pa. © 2007 Elsevier B.V. All rights reserved.

In this work, the relation between oxidant/monomer ratio and the electrical conductivity of polypyrrole was studied using different ratios. We achieved a maximum value for electrical conductivity of 7.5 S/cm for a ratio of 2:1. We also developed a chemical dip-coating process to produce the cathode layer in tantalum capacitors. We obtained capacitances of about 80 μF after 8 cycles using the sequence Monomer/Oxidant.

Insensitivity to light irradiation is desirable for conventional applications of thin-film transistors, i.e., the active matrices of displays. However, if one produces a device presenting controlled sensitivity to light, many other applications can benefit or can even be created. In this work it is shown the influence of the photon energy on the optoelectronic properties presented by n-type bottom-gate thin-film transistors based on indium zinc oxide. In the dark, the devices present very good electrical properties, working in the enhancement mode, exhibiting on-off ratios higher than 107 and channel mobility above 30 cm2/V s. Remarkable results were achieved when the devices were exposed to light radiation, the most striking one is the possibility to switch between enhancement (in the dark) and depletion (illuminated) modes, with different threshold voltages and on/off ratios, function of the light power density and wavelength used. This type of behavior permits to design circuits where one can have the same transistor working either in the enhancement or depletion modes, function of the light beam and intensity impinging on it, highly important for short wavelength detector applications. © 2006 Elsevier B.V. All rights reserved.

In this work, HfO2 was deposited by r.f. sputtering at room temperature and then annealed for different times at 200°C in a forming gas atmosphere. After annealing for 2 hours the HfO2 layers present a reduction on the flat band voltage of about 1 V, relatively to the as deposited film, decreasing from -2.23V down to -1.28 V. This means an improvement of the interface properties and a reduction on the oxide charge density from 1.33×1012 cm-2 to 7.62×1011 cm -2. The dielectric constant reaches a maximum of 18.3 after 5h annealing due to film's densification. When annealing for longer times such as 10h a small degradation of the electrical properties is observed. After 10h annealing the dielectric constant, flat band voltage and fixed charge density are respectively, 14.9, -2.96 V and 1.64×1012 cm-2 and the leakage current also increases due to film's crystallization.

Nanocrystalline hydrogenated silicon (nc-Si:H) thin films are generally accepted to be a two phase material-Si crystalline and Si:H amorphous. This work reports the use of impedance spectroscopy to determine the amorphous and crystalline electrical conductivity of a/nc-Si:H films obtained by hot wire chemical vapour deposition. Different relaxation time or time constants are detected, if the film is composed by inhomogeneous material, by measuring ac impedance in a wide range of frequencies. Relating the conduction mechanism of the film to a series of two RC circuits constituted by a resistance and a capacitor in parallel, we may determine distinct ac conductivities and correlate that to the crystalline, amorphous and interface components. The amorphous films analysed exhibit one ac conductivity component while for nanocrystalline films two ac conductivity components are observed. The average value of ac conductivities is in agreement with that of dc conductivity. © 2006.

The electrosynthesis of polypyrrole (PPy) has been achieved on aluminium in aqueous medium of tartaric acid by means of cyclic voltammetry, potentiostatic and galvanostatic techniques. Scanning electron microscopy (SEM) and X-ray microanalysis by energy spectroscopy dispersion (EDS) applying on surfaces show that the PPy coating is developed from the metal surface through the cracks of the initial Al2O3 layer. A mechanism involving the participation of the supporting electrolyte and the pyrrole (Py) in distinct active sites was proposed based on the linear sweep voltammetry. It is observed for all applied electrochemical techniques that the pyrrole concentration has to be higher than 0.1 M to allow the polypyrrole electrodeposition in acid medium. Scanning electron microscopy, secondary electrons (SE) and backscattering electrons (BE), shows that the PPy coating obtained in galvanostatic and potentiostatic modes starts with small islands at weak applied potentials or current densities. Moreover, EDS reveals a good homogeneity and compactness of the film achieved in galvanostatic method. The corrosion results in 3% NaCl medium show that the PPy coating decreases the corrosion behaviour of the aluminium. The bilayer Al2O3/PPy shows a capacitor with future applications. © 2006 Elsevier Ltd. All rights reserved.

This paper discusses the electron transport and the optical characteristics of amorphous indium zinc oxide and the role of the oxygen partial pressure on tailoring its properties. The data show that by varying the oxygen partial pressure during the deposition process from 10-3 to 2 × 10-1 Pa, the electrical resistivity varies from about 10-4 to 2 × 101 Ω cm, which corresponds to a variation on the Hall mobility from 60 to 10 cm2 V-1 s-1. The conductivity and mobility analysis show that the transport of carriers is not band tail limited, as happens in conventional disordered semiconductors, but highly dependent on the ionicity and the presence of oxygen vacancies, where mobility is mainly limited by carrier scattering. The optical characteristics inferred from the transmittance data reveal films with optical gaps in the range of 3.68-3.76 eV, very close to the ones observed on crystalline/polycrystalline IZO films (3.7-3.9 eV). © 2006 Elsevier B.V. All rights reserved.

It is experimentally known that the linearity and sensitivity of the position sensitive detectors (PSD) are dependent on the resistance of the collecting layer and of the load resistance, mainly if the detection is based on the measurement of the photo-lateral voltage. To determine the value of the load resistance to be used in metal - insulator - semiconductor (MIS) PSDs structures that lead to the maximum value of sensitivity and linearity, we propose an electrical model through which it is able to simulate the proper sensor response and how the load resistance influence the results obtained. This model is valid for PSDs where the resistance of the collecting resistive layer is quite low (≤ 500 Ω), leading to a low output impedance. Under these conditions we conclude that the value of the load resistance should be of about 1 kΩ in order to achieve a good compromise between the linearity and the sensitivity of the PSD. This result is in agreement with the set of experiments performed. © 2005 Materials Research Society.

This work presents a study on the effect of an interfacial silicon oxide layer placed between Au and a-Si:H MIS (metal-insulator-semiconductor) photodiodes in their performances, by stopping the Au diffusion towards the a-Si:H. The results show that the Au diffuses very easily to the oxide free a-Si:H surface, even at room temperature, degrading the photodiode performance. On the other hand, the MIS photodiodes with the interfacial oxide show an improvement of their characteristics after annealing, function of its thickness, and degree of film's compactness. This effect is associated with the presence of oxide of thicknesses ≥5 Å at the Au/a-Si:H interface that prevents the Au diffusion and improves the photodiode characteristics, which does not happen when the interfacial oxide is absent. © 2004 Elsevier B.V. All rights reserved.

This work presents a study performed on several Au contacts deposited by evaporation on oxide free and oxidised (5-20Å of oxide) a-Si:H surfaces. The characterisation of the films was performed on as deposited, aged and annealed at 150°C structures. SIMS and RBS measurements show that the Au diffuses very easily on oxide free a-Si:H surfaces, even at room temperature, resulting in the formation of an oxide at the device surface that acquires a blue colour instead of the gold colour of the contacts. This was also visible in the SEM pictures of the cross section of the structures produced and on the changes of the surface morphology observed by AFM measurements. On the other hand, when the Au is deposited on oxidised a-Si:H surfaces, the results show that the oxide prevents the Au from diffusing and the nature of the contact is preserved. That is, better rectifying and stability performances are obtained in MIS like structures than in Schottky structures.

This work presents a study performed on the deposition of pm-Si:H by plasma enhanced chemical vapor deposition using excitation frequencies of 13.56 and 27.12 MHz, where the interest of increasing the excitation frequency relies on higher plasma dissociation and reduced energy of ion bombardment, thus allowing the deposition of superior grade material at higher growth rates. The plasma impedance, which allows the monitoring of particle formation in the plasma, was correlated to the film properties, characterized by spectroscopic ellipsometry and hydrogen exodiffusion experiments. The set of data obtained show that by using the 27.12-MHz excitation frequency the hydrogen dilution and the r.f. power density needed to produce pm-Si:H can be reduced. Growth rates above 3.1 Å/s were obtained, the films being more dense and chemically more stable than those obtained with the standard 13.56 MHz. © 2003 Elsevier B.V. All rights reserved.

In this work metal-insulator-semiconductor (MIS) photodiodes with a structure: Cr/a-Si:H(n+)/a-Si:H(i)/oxide/Au were studied, where the main objective was to determine the influence of the oxide layer on the performance of the devices. The results achieved show that their performance is a function of both oxide thickness and oxide density. The a-Si:H oxidation method used was the immersion in H2O2 solution. By knowledge of the oxide growth process it was possible to fabricate photodiodes exhibiting an open circuit voltage of 0.65V and short circuit current density under AM1.5 illumination of 11mA/cm2, with a response times less than 1μs for load resistance <400Ω, and a signal to noise ratio of 1×107. © 2003 Elsevier B.V. All rights reserved.

In this work we present results of a study performed on metal-insulator-semiconductor (MIS) diodes with the following structure: substrate (glass)/Cr (2000 Å)/a-Si:H n+(400 Å)/a-Si:H i (5500 Å)/oxide (0-40 Å)/Au (100 Å) to determine the influence of the oxide passivation layer grown by different techniques on the electrical performance of MIS devices. The results achieved show that the diodes with oxides grown using hydrogen peroxide present higher rectification factor (2×106) and signal to noise (S/N) ratio (1×10 7 at -1 V) than the diodes with oxides obtained by the evaporation of SiO2, or by the chemical deposition of SiO2 by plasma of hexamethyldisiloxane. However, in the case of deposited oxides, the breakdown voltage is higher, 30 V instead of 3-10 V for grown oxides. The ideal oxide thickness, determined by spectroscopic ellipsometry, is dependent on the method used to grow the oxide layer and is in the range between 6 and 20 Å. The reason for this variation is related to the degree of compactation of the oxide produced, which is not relevant for applications of the diodes in the range of ±1 V, but is relevant when high breakdown voltages are required. © 2003 Elsevier B.V. All rights reserved.

Shape memory alloys (SMA) represents a class of metallic materials that has the capability of recovering a previously defined initial shape when subject to an adequate thermomechanical treatment. The present work aims to study the influence of thermal cycles on the transition temperatures of a Ni-Ti alloy. In this system, small variations around the equiatomic composition give rise to significant transformation temperature variations ranging from 173 to 373 K. SMA usually presents the shape memory effect after an annealing treatment at ca. 973 K. The optimisation of the thermomechanical treatment will allow to "tune" the material to different transformation temperature ranges from the same starting material, just by changing the processing conditions. Differential scanning calorimeter (DSC) and in situ high-temperature X-ray diffraction (XRD) have been used to identify the transformation temperatures and the phases that are present after different thermal cycles. The results concerning a series of thermal cycles with different heating and cooling rates (from 1.67×10-2 to 1.25×10-1 K/s) and different holding temperatures (from 473 to 1033 K) are presented. © 2004 Elsevier B.V. All rights reserved.

In this paper we present the effect of the insertion of a non-doped nanocrystalline zinc oxide/buffer layer on the electrical, optical and structural properties of indium tin oxide produced at room temperature by radio frequency plasma enhanced reactive thermal evaporation on polymeric substrates. The electrical resistivity of the ITO films is reduced by more than two orders of magnitude (4.5×10-1 to 2.9×10-3 Ωcm). From the Hall effect measurements it is observed that the large decrease associated to the electrical resistivity, is due to the increase associated to the Hall mobility. Concerning the optical properties no effect was observed, being the transmittance in the visible and near the infra red region always higher than 80%.

In this work, we show the possibility to use undoped porous silicon (PS) thin films produced by hot wire chemical vapour deposition technique (HW-CVD) as ethanol detector. Silicon thins films produced by HW-CVD technique, under certain deposition conditions, have a porous structure [Vacuum 52 (1999) 147]. Therefore, in the presence of an alcohol, the OH group is adsorbed by the uncompensated bonds behaving as donor-like carriers leading to an increase in the current flowing through the material. This current enhancement is bias dependent in glass/ITO/i-a-Si:H/Al sensor and increases as the ethanol vapour pressure increases from 10-1mbar to atmospheric pressure. The response time of the current of the sensor and its recovery time are in the range of 10-50s at room temperature. Ethanol quantities above 50ppm can be detected. © Published by Elsevier B.V.

The need to improve the efficiency of the European university system is discussed. It is considered possible to increase university funding by letting students pay for their education. It is suggested that European universities raise more money for research from private sources by selling services. It is found appropriate to strive for excellence at the level of specific departments or schools to begin with.

In this work we studied the influence of the dopant elements and concentration on the properties of ZnO thin film deposited by spray pyrolysis. The results show that the doping affects the thin films properties mainly the electrical ones, function of dopant concentration and nature. The most important changes were observed for films doped with 1at% of indium which exhibit a resistivity of 1.9 × 10-1 Ωcm associated with a transmitance of 90%. After the annealing treatment, the resistivity of the film decreases to 5.9 × 10-3 Ωcm without significative changes in the optical properties. The films were also used to produce amorphous silicon solar cells where the best results were obtained for ZnO:In. © 2002 Elsevier Science Ltd. All rights reserved.

Where a-Si:H pin devices are concerned, one of the main obstacles regarding improved performance is device stability, usually attributed to adverse behaviour at various interfaces within the device. Several attempts have been made to overcome this problem, such as the use of blocking layers at the interfaces. Although these have led to some improvements in device performance, most of the problems associated with device stability remain. This is mainly due to the defects at the interfaces, since the blocking layers (silicon alloys with carbon, nitrogen or oxygen) usually have a high density of bulk states, in comparison to intrinsic a-Si:H films. In this paper, we present a method that seems to be capable of improving device stability. It consists of performing a controlled removal of oxide interlayers at the interfaces, by an appropriate etching process. This enables the production of highly smoothed interfaces, and reduces possible cross-contamination of the i-layer from the adjacent doped layers. This amounts to a new design of typical pin devices, in which thin absorber layers are placed at the p/i and i/n interfaces. Their purpose is to trap most of the impurity atoms diffused from the doped layers, after which they are removed by appropriate etching. The fabrication of the absorbers (sacrificial layers), the nature of the etching and the tailoring of the defect profile at the interfaces will be discussed, including the performance exhibited by the resulting devices. © 2002 Elsevier Science B.V. All rights reserved.

In this work we present the results of a study concerning the role of the properties of zinc oxide thin films deposited by spray pyrolysis on its sensitivity to methane or ethane. It was found that using highly resistive thin layers leads to an increase in the film sensitivity. The variation of the operating temperature of the film leads to a significant change in the sensitivity of the sensor and the ideal operating temperature dependence of the gas used. The sensitivity of the ZnO thin films changes linear with the increase of the gas concentration. However these films seem to be more appropriated for the detection of methane than for ethane since the value of sensitivity obtained are higher and its variation with the gas concentration more pronounced. After the annealing treatment performed the films sensitivity decreases.

The influence of doping on the properties of zinc oxide thin films deposited by spray pyrolysis has been studied. The results show that the doping affects the properties of the films, mainly the electrical ones, function of its concentration and nature. The most significative improvement were observed for films doped with 1 at.% of indium exhibiting a resistivity of 1.9 × 10-1 Ω m associated to a transmittance of 86%, characteristics required for applications on the optoelectronic devices. © 2001 Elsevier Science Ltd. All rights reserved.

The influence of different TCOs (SnO2 and ITO) on the photoelectrical properties of 1-D position sensitive detectors based on p-i-n structures was studied. A strong cross-contamination in the p-layer and contamination in the i-layer reduce the quality of the device. Numerical analysis of TCO/p-i-n structure also revealed a strong increase in defect states at the p-layer surface which can be attributed to the reduction of TCO. ITO seems to be less appropriate for a front TCO, although the spectral response of the p-i-n structure under reverse bias is not significantly affected by the conditions at the TCO/p heterojunction.

In this paper we report results concerning the effect of the TCO interface on hydrogenated amorphous silicon (a-Si:H) p-i-n homojunction solar cells. Its correlation with dark current density-voltage (J-V) characteristics and spectral response, before and after while light-soaking degradation, is analysed. From this study, we conclude that the properties and stability of these devices are not only influenced by the a-Si:H film properties, but also by the properties of the transparent conductive electrode and its interface with the a-Si:H layer.

This paper deals with the engineering aspects related to the rf energy coupling in Plasma Enhanced Chemical Vapour Deposition (PECVD) processes, in a diode-type unit in which an extra grid is used. The main emphasis is given in the determination of the real power delivered to the gas and comparing it with the total power losses, besides determining the best way to control the powder formed during the process. © 1994.

One of the main problems in producing large area amorphous silicon devices concerns films uniformity. In this paper we present data concerning the role of reactor geometry and design and on the film performances as well as the problems related to mechanical mismatches in scaling up the reactor size. © 1991 Elsevier Science Publishers B.V. All rights reserved.