Rodrigo Martins

An advanced compact and analytical drain current model for the amorphous gallium indium zinc oxide (GIZO) thin film transistors (TFTs) is proposed. Its output saturation behavior is improved by introducing a new asymptotic function. All model parameters were extracted using an adapted version of the Universal Method and Extraction Procedure (UMEM) applied for the first time for GIZO devices in a simple and direct form. We demonstrate the correct behavior of the model for negative VDS, a necessity for a complete compact model. In this way we prove the symmetry of source and drain electrodes and extend the range of applications to both signs of VDS. The model, in Verilog-A code, is implemented in Electronic Design Automation (EDA) tools, such as Smart Spice, and compared with measurements of TFTs. It describes accurately the experimental characteristics in the whole range of GIZO TFTs operation, making the model suitable for the design of circuits using these types of devices. © 2016 Elsevier Ltd

The interaction of light with wavelength-sized photonic nanostructures is highly promising for light management applied to thin-film photovoltaics. Several light trapping effects come into play in the wave optics regime of such structures that crucially depend on the parameters of the photonic and absorbing elements. Thus, multi-parameter optimizations employing exact numerical models, as performed in this work, are essential to determine the maximum photocurrent enhancement that can be produced in solar cells.Generalized spheroidal geometries and high-index dielectric materials are considered here to model the design of the optical elements providing broadband absorption enhancement in planar silicon solar cells. The physical mechanisms responsible for such enhancement are schematized in a spectral diagram, providing a deeper understanding of the advantageous characteristics of the optimized geometries. The best structures, composed of TiO2 half-spheroids patterned on the cells' top surface, yield two times higher photocurrent (up to 32.5 mA/cm2 in 1.5 μm thick silicon layer) than the same devices without photonic schemes.These results set the state-of-the-art closer to the theoretical Lambertian limit. In addition, the considered light trapping designs are not affected by the traditional compromise between absorption enhancement versus current degradation by recombination, which is a key technological advantage. © 2016 Elsevier Ltd.

The intense light scattered from metal nanoparticles sustaining surface plasmons makes them attractive for light trapping in photovoltaic applications. However, a strong resonant response from nanoparticle ensembles can only be obtained if the particles have monodisperse physical properties. Presently, the chemical synthesis of colloidal nanoparticles is the method that produces the highest monodispersion in geometry and material quality, with the added benefits of being low-temperature, low-cost, easily scalable and of allowing control of the surface coverage of the deposited particles. In this paper, novel plasmonic back-reflector structures were developed using spherical gold colloids with appropriate dimensions for pronounced far-field scattering. The plasmonic back reflectors are incorporated in the rear contact of thin film n-i-p nanocrystalline silicon solar cells to boost their photocurrent generation via optical path length enhancement inside the silicon layer. The quantum efficiency spectra of the devices revealed a remarkable broadband enhancement, resulting from both light scattering from the metal nanoparticles and improved light incoupling caused by the hemispherical corrugations at the cells' front surface formed from the deposition of material over the spherically shaped colloids. © 2015 IOP Publishing Ltd.

Electrochemically active bacteria (EAB) have the capability to transfer electrons to cell exterior, a feature that is currently explored for important applications in bioremediation and biotechnology fields. However, the number of isolated and characterized EAB species is still very limited regarding their abundance in nature. Colorimetric detection has emerged recently as an attractive mean for fast identification and characterization of analytes based on the use of electrochromic materials. In this work, WO 3 nanoparticles were synthesized by microwave assisted hydrothermal synthesis and used to impregnate non-treated regular office paper substrates. This allowed the production of a paper-based colorimetric sensor able to detect EAB in a simple, rapid, reliable, inexpensive and eco-friendly method. The developed platform was then tested with Geobacter sulfurreducens, as a proof of concept. G. sulfurreducens cells were detected at latent phase with an RGB ratio of 1.10 ± 0.04, and a response time of two hours.

Photocurrent enhancement in thin a-Si:H solar cells due to the plasmonic light trapping is investigated, and correlated with the morphology and the optical properties of the selfassembled silver nanoparticles incorporated in the cells' back reflector. © 2014 Optical Society of America.

Curcuma longa L., also known as turmeric, is widely used as a food colorant and has been reported to have antioxidant, anti-inflammatory, anti-mutagenic and anti-cancer properties. The aim of this study was to evaluate the effects of the spray drying on curcuminoid and curcumin contents, antioxidant activity, process yield, the morphology and solubility of the microparticulated solid dispersion containing curcuma extract using a Box Behnken design. The microparticles were spherical in shape, and an increase in outlet temperature from 40 to 80 °C resulted in a significant increase in the yield of microparticles from 16 to 53%. The total curcuminoid content (17.15 to 19.57. mg/g), curcumin content (3.24 to 4.25. mg/g) and antioxidant activity (530.1 to 860.3 μg/mL) were also affected by the spray drying process. The solubility of curcuminoid from C. longa remarkably improved 100-fold in the microparticles, confirming the potential of the ternary solid dispersion technique to improve the dyeing and nutraceutical properties of these compounds. Furthermore, the microparticles were obtained using the spray drying process, can be easily scaled up. © 2011 Elsevier Ltd.

The aim of this study was to investigate the influence of ultrasound and high-shear mixing on the properties of microparticles obtained by spray congealing. Dispersions containing 10% carbamazepine and 90% carrier Gelucire® 50/13 (w/w) were prepared using magnetic stirring, high-shear mixing, or ultrasound. Each preparation was made using hot-melt mixing spray congealing to obtain the microparticles. All microparticles presented a spherical shape with high encapsulation efficiency (>99%). High-shear mixing and ultrasound promoted a decrease in the size of microparticles (D90) to 62.8 ± 4.1 μm and 64.9 ± 3.3 μm, respectively, while magnetic stirring produced microparticles with a size of 84.1 ± 1.4 μm. The use of ultrasound led to microparticles with increased moisture content as identified through sorption isotherm studies. In addition, rheograms showed distinct rheological behaviour among different dispersion preparations. Therefore, the technique used to prepare dispersions for spray congealing can affect specific characteristics of the microparticles and should be controlled during the preparation. © 2013 Informa UK Ltd. All rights reserved.

In this paper we report results concerning the use of paper as substrate and as an electronic component for the next generation of sustainable low cost electronic systems, where different examples of applications are given. © 2013 Society for Information Display.

The ability to process and dimensionally scale field-effect transistors with and on paper and to integrate them as a core component for low-power-consumption analog and digital circuits is demonstrated. Low-temperature-processed p- and n-channel integrated oxide thin-film transistors in the complementary metal oxide semiconductor (CMOS) inverter architecture are seamlessly layered on mechanically flexible, low-cost, recyclable paper substrates. The possibility of building these circuits using low-temperature processes opens the door to new applications ranging from smart labels and sensors on clothing and packaging to electronic displays printed on paper pages for use in newspapers, magazines, books, signs, and advertising billboards. Because the CMOS circuits reported constitute fundamental building blocks for analog and digital electronics, this development creates the potential to have flexible form factor computers seamlessly layered onto paper. The holistic approach of merging low-power circuitry with a recyclable substrate is an important step towards greener electronics. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

P-type thin-film transistors (TFTs) using room temperature sputtered tin and copper oxide as a transparent oxide semiconductor have been produced on rigid and paper substrates. The SnO x films shows p-type conduction presenting a polycrystalline structure composed with a mixture of tetragonal β-Sn and α-SnO x phases, after annealing at 200°C. These films exhibit a hole carrier concentration in the range of ≈ 10 16-10 18 cm -3, electrical resistivity between 101-102 Ωcm, Hall mobility of 4.8 cm 2/Vs, optical band gap of 2.8 eV and average transmittance ≈ 85 % (400 to 2000 nm). Concerning copper oxide Cu xO thin films they exhibit a polycrystalline structure with a strongest orientation along (111) plane. The Cu xO films produced between an oxygen partial pressure of 9 to 75% showed p-type behavior, as it was measured by Hall effect and Seebeck measurements. The bottom gate p-type SnO x TFTs present field-effect mobility above 1.24 cm 2/Vs (including the paper p-type oxide TFT) and an on/off modulation ratio of 10 3 while the Cu xO TFTs exhibit a field-effect mobility of 1.3×10 -3 cm 2/Vs and an on/off ratio of 2×10 2. © 2012 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

Today there is a strong interest in the scientific and industrial community concerning the use of biopolymers for electronic applications, mainly driven by low-cost and disposable applications. Adding to this interest, we must recognize the importance of the wireless auto sustained and low energy consumption electronics dream. This dream can be fulfilled by cellulose paper, the lightest and the cheapest known substrate material, as well as the Earth's major biopolymer and of tremendous global economic importance. The recent developments of oxide thin film transistors and in particular the production of paper transistors at room temperature had contributed, as a first step, for the development of disposable, low cost and flexible electronic devices. To fulfil the wireless demand, it is necessary to prove the concept of self powered devices. In the case of paper electronics, this implies demonstrating the idea of self regenerated thin film paper batteries and its integration with other electronic components. Here we demonstrate this possibility by actuating the gate of paper transistors by paper batteries. We found that when a sheet of cellulose paper is covered in both faces with thin layers of opposite electrochemical potential materials, a voltage appears between both electrodes - paper battery, which is also self-regenerated. The value of the potential depends upon the materials used for anode and cathode. An open circuit voltage of 0.5V and a short-circuit current density of 1μA/cm2 were obtained in the simplest structure produced (Cu/paper/Al). For actuating the gate of the paper transistor, seven paper batteries were integrated in the same substrate in series, supplying a voltage of 3.4V. This allows proper ON/OFF control of the paper transistor. Apart from that transparent conductive oxides can be also used as cathode/anode materials allowing so the production of thin film batteries with transparent electrodes compatible with flexible, invisible, self powered and wireless electronics. © 2011 SPIE.

A complementary metal oxide semiconductor (CMOS) device is described. The device is based on n-(In-Ga-Zn-O) and p-type (SnO x) active oxide semiconductors and uses a transparent conductive oxide (In-Zn-O) as gate electrode that sits on a flexible, recyclable paper substrate that is simultaneously the substrate and the dielectric. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Today there is a strong interest in the scientific and industrial community concerning the use of biopolymers for electronic applications, driven mainly by low-cost and disposable applications. Adding to this interest, we must recognise the importance of the dream of wireless auto-sustained and low-energy-consumption electronics. This dream can be fulfilled by cellulose paper, the lightest and the cheapest known substrate material, as well as the Earth's major biopolymer and of tremendous global economic importance. Most of the paper used up to now is optimised in terms of the required mechanical and physical properties to be used as the support of inks of different origins. In the future, specific electronic heterogeneous paper sheets should be fabricated aiming to get paper fibers with required bulk and surface functionalities, proper water/vapour barrier, size and diameter/thickness of the fibrils and full paper thickness. This will be the function of components/devices to be incorporated/integrated such as thin-film transistors, complementary metal oxide semiconductor devices, passive electronic components (resistances, inductors and capacitors), memory transistors, electrochromics and thin-film paper batteries. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Reported herein is a nonvolatile n-type floating gate memory paper field-effect transistor, emphasizing the role of the paper structure and properties on the device performance recorded such as in the high capacitance per unit area at low frequencies (>2.5 μFcm-2) and so on the set of high charge retention times achieved (>16000 hours). The device was built via the hybrid integration of natural cellulose fibers, which act simultaneously as substrate and gate dielectric, using amorphous indium zinc and gallium indium zinc oxides respectively for the gate electrode and channel layer. This was complemented by the use of continuous patterned metal layers as source/drain electrodes. © 2010 Copyright SPIE - The International Society for Optical Engineering.

The special Professor Walter E. Spear commemoration issue of the Philosophical Magazine, published in October 2009, contains papers which cover the numerous relevant issues, driven by commercial applications, primarily solar energy and displays. Kocka reviews the complex microstructure of crystallites embedded in the amorphous silicon tissue, the transport mechanism is determined by the conductive grains and influenced by the passivation through H at the grain boundaries. Hugger and co-researchers report on transient photocapacitance spectroscopy and drive-level capacitance profiling as a way of elucidating the fundamental electronic properties of hydrogenated ncSi. Tawada recounts the history of a-Si:H pin heterojunction solar cells, emphasizing the role of the p-type silicon carbide layer in the improvement of the device. Schubert and colleagues focus their work on the production of flexible PV modules with many applications in the architectural arena or integrated into clothing.

This paper reports the performance of small area solar cells, 128 linear integrated position sensitive detector arrays and thin film transistors based on nanostructured silicon thin films produced by plasma-enhanced chemical vapour deposition technique, close to the onset of dusty plasma conditions, within the transition region from amorphous to microcrystalline. The small area solar cells, produced in a modified single chamber reactor, exhibited very good electrical characteristics with a conversion efficiency exceeding 9%. The 128 integrated position sensitive detector arrays, based on a similar pin structure, allow real-time 3D object imaging with a resolution higher than 90 l p/mm. The thin film transistors produced exhibited field effect mobility of 2.47 cm 2/V/s, threshold voltage of 2 V, on/off ratio larger than 10 7 and sub-threshold slopes of 0.32 V/decade, which are amongst the best results reported for this type of device. © 2009 Taylor & Francis.

Here we report the performance of a selective floating gate (V GS) n-type non-volatile memory paper field-effect transistor. The paper dielectric exhibits a spontaneous polarization of about 1 mCm-2 and GIZO and IZO amorphous oxides are used respectively as the channel and the gate layers. The drain and source regions are based in continuous conductive thin films that promote the integration of fibres coated with the active semiconductor. The floating memory transistor writes, reads and erases the stored information with retention times above 14500 h, and is selective (for VGS > 5 ± 0.1 V). That is, to erase stored information a symmetric pulse to the one used to write must be utilized, allowing to store in the same space different information. © 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

This paper discusses the effect of order and disorder on the electrical and optical performance of ionic oxide semiconductors based on zinc oxide. These materials are used as active thin films in electronic devices such as pn heterojunction solar cells and thin-film transistors. Considering the expected conduction mechanism in ordered and disordered semiconductors the role of the spherical symmetry of the s electron conduction bands will be analyzed and compared to covalent semiconductors. The obtained results show p-type c-Si/a-IZO/poly-ZGO solar cells exhibiting efficiencies above 14% in device areas of about 2.34 cm2. Amorphous oxide TFTs based on the Ga-Zn-Sn-0 system demonstrate superior performance than the polycrystalline TFTs based on ZnO, translated by ION/IOFF ratio exceeding 107, turn-on voltage below 1-2 V and saturation mobility above 25 cm2/Vs. Apart from that, preliminary data on p-type oxide TFT based on the Zn-Cu-O system will also be presented. © 2009 SPIE.

The electron transport in n-type polycrystalline zinc oxide, nanocrystalline Zinc-Gallium-Oxygen and amorphous Indium-Zinc-Oxygen systems produced by rf magnetron sputtering at room temperature, under different oxygen partial pressure were investigated. It was found that the carrier transport is not band tail limited, being governed by metal cations irrespective to the film's structure. The highest net room temperature electron mobility was achieved on the amorphous films and noticed that for the single component oxides the mobility decreases as the carrier concentration increases, while the reverse behaviour was observed for the multicomponent oxides, independently of their structure. These behaviours are related to the role that negative charge defects in excess of 1010 cm- 2 generated on multicomponent oxides have on carriers scattering and so on their electronic performances. © 2007 Elsevier B.V. All rights reserved.

This paper describes a novel colorimetric method for detection of nucleic acid targets in a homogeneous format with improved sensitivity by means of a system based on the combination of a tunable monochromatic light source and an amorphous/nanocrystalline silicon photodetector that detects color and light intensity changes undergone by samples/assays containing tailored gold nanoparticles probes. This new low cost, portable, fast and simple optoelectronic platform, with the possibility to be re-used, permits detection of at least 400 fentomole of specific DNA sequences without target or signal amplification and was applied to the rapid detection of human pathogens in large variety of clinical samples such as Mycobacterium tuberculosis. © 2008 Elsevier B.V. All rights reserved.

We report the architecture and the performances of a memory based on a single field-effect transistor built on paper able to write-erase and read. The device is composed of natural multilayer cellulose fibers that simultaneously act as structural support and gate dielectric; active and passive multicomponent amorphous oxides that work as the channel and gate electrode layers, respectively, complemented by the use of patterned metal layers as source/drain electrodes. The devices exhibit a large counterclockwise hysteresis associated with the memory effect, with a turn-on voltage shift between 1 and -14.5 V, on/off ratio and saturation mobilities of about 104 and 40 cm 2 V-1 s-1, respectively, and estimated charge retention times above 14 000 h. © 2008 American Institute of Physics.

Amorphous/nanocrystalline silicon p i′ i i′ n devices fabricated on micromachined glass substrates are integrated with oligonucleotide-derivatized gold nanoparticles for a colorimetric detection method. The method enables the specific detection and quantification of unamplified nucleic acid sequences (DNA and RNA) without the need to functionalize the glass surface, allowing for resolution of single nucleotide differences between DNA and RNA sequences-single nucleotide polymorphism and mutation detection. The detector's substrate is glass and the sample is directly applied on the back side of the biosensor, ensuring a direct optical coupling of the assays with a concomitant maximum photon capture and the possibility to reuse the sensor. © 2007 American Institute of Physics.

This paper aims to discuss the effect of order and disorder on the electrical performances of covalent silicon semiconductors and ZnO based ionic oxide semiconductors used as active channel layers in thin film transistors. The effect of disorder on covalent semiconductors directly affects their electrical transport properties due to the asymmetric behaviour of sp states, while in ionic oxide semiconductors it is found that this effect is small due to the fact that angular disorder has no effect on the spherical symmetry of s states. To this we must add that the mobility of carriers in both systems is quite different, being also affected by electron-phonon interactions (weak in silicon and strong in ionic oxides leading to formation of polarons). Besides, the impurity doping effect and the presence of vacancies in disordered silicon and in ionic oxides behave differently, which will influence the thin film properties and so, the performances of the devices produced. © 2007 Springer-Verlag.

The role of order and disorder on the electronic performances of n -type ionic oxides such as zinc oxide, gallium zinc oxide, and indium zinc oxide used as active (channel) or passive (drain/source) layers in thin film transistors (TFTs) processed at room temperature are discussed, taking as reference the known behavior observed in conventional covalent semiconductors such as silicon. The work performed shows that while in the oxide semiconductors the Fermi level can be pinned up within the conduction band, independent of the state of order, the same does not happen with silicon. Besides, in the oxide semiconductors the carrier mobility is not bandtail limited and so disorder does not affect so strongly the mobility as it happens in covalent semiconductors. The electrical properties of the oxide films (resistivity, carrier concentration, and mobility) are highly dependent on the oxygen vacancies (source of free carriers), which can be controlled by changing the oxygen partial pressure during the deposition process and/or by adding other metal ions to the matrix. In this case, we make the oxide matrix less sensitive to the presence of oxygen, widening the range of oxygen partial pressures that can be used and thus improving the process control of the film resistivity. The results obtained in fully transparent TFT using polycrystalline ZnO or amorphous indium zinc oxide (IZO) as channel layers and highly conductive poly/nanocrystalline ZGO films or amorphous IZO as drain/source layers show that both devices work in the enhancement mode, but the TFT with the highest electronic saturation mobility and on/off ratio 49.9 cm2 V s and 4.3× 108, respectively, are the ones in which the active and passive layers are amorphous. The ZnO TFT whose channel is based on polycrystalline ZnO, the mobility and on/off ratio are, respectively, 26 cm2 V s and 3× 106. This behavior is attributed to the fact that the electronic transport is governed by the s -like metal cation conduction bands, not significantly affected by any type of angular disorder promoted by the 2p O states related to the valence band, or small amounts of incorporated metal impurities that lead to a better control of vacancies and of the TFT off current. © 2007 American Institute of Physics.