Rodrigo Martins

The aim of this work is to provide the basis for the interpretation, under steady state conditions, of the lateral photoeffect in p-i-n a-Si:H one-dimensional thin-film position-sensitive detectors (1D TFPSD) and the determination of its linear spatial detection limits, function of the device, and light spot source characteristics. This leads to the development of a model, based on the application of the Poisson, continuity, and current density equations in the p-i-n junction, where two thin resistive layers, as equipotentials, are considered on both sides of the doped layers. The experimental data recorded in 1D TFPSD devices with different performances are compared with the predicted curves and the obtained correlations discussed. © 1995 American Institute of Physics.

N- and p-type weakly absorbing and highly conductive microcrystalline thin μc-Six:Cy:Oz:H films, have been produced by a TCDDC (Two Consecutive Decomposition and Deposition Chamber) system1. The optoelectronic and structural results show that we are in the presence of a mixed phase of Si microcrystals (c-islands) embedded in a-Six:Cy:Oz:H (a-tissue). Based on that, we propose a model where transport mechanisms are explained by the potential fluctuations related to films heterogeneities. Thus, conduction is due to carriers that by tunneling or percolation "pass" or "go" trough the barriers and/or percolate randomly by the formed channels. © 1989.

Curcuma longa L., also known as turmeric, is widely used as a food colorant and has been reported to have antioxidant, anti-inflammatory, anti-mutagenic and anti-cancer properties. The aim of this study was to evaluate the effects of the spray drying on curcuminoid and curcumin contents, antioxidant activity, process yield, the morphology and solubility of the microparticulated solid dispersion containing curcuma extract using a Box Behnken design. The microparticles were spherical in shape, and an increase in outlet temperature from 40 to 80 °C resulted in a significant increase in the yield of microparticles from 16 to 53%. The total curcuminoid content (17.15 to 19.57. mg/g), curcumin content (3.24 to 4.25. mg/g) and antioxidant activity (530.1 to 860.3 μg/mL) were also affected by the spray drying process. The solubility of curcuminoid from C. longa remarkably improved 100-fold in the microparticles, confirming the potential of the ternary solid dispersion technique to improve the dyeing and nutraceutical properties of these compounds. Furthermore, the microparticles were obtained using the spray drying process, can be easily scaled up. © 2011 Elsevier Ltd.

The role of order and disorder on the electronic performances of n -type ionic oxides such as zinc oxide, gallium zinc oxide, and indium zinc oxide used as active (channel) or passive (drain/source) layers in thin film transistors (TFTs) processed at room temperature are discussed, taking as reference the known behavior observed in conventional covalent semiconductors such as silicon. The work performed shows that while in the oxide semiconductors the Fermi level can be pinned up within the conduction band, independent of the state of order, the same does not happen with silicon. Besides, in the oxide semiconductors the carrier mobility is not bandtail limited and so disorder does not affect so strongly the mobility as it happens in covalent semiconductors. The electrical properties of the oxide films (resistivity, carrier concentration, and mobility) are highly dependent on the oxygen vacancies (source of free carriers), which can be controlled by changing the oxygen partial pressure during the deposition process and/or by adding other metal ions to the matrix. In this case, we make the oxide matrix less sensitive to the presence of oxygen, widening the range of oxygen partial pressures that can be used and thus improving the process control of the film resistivity. The results obtained in fully transparent TFT using polycrystalline ZnO or amorphous indium zinc oxide (IZO) as channel layers and highly conductive poly/nanocrystalline ZGO films or amorphous IZO as drain/source layers show that both devices work in the enhancement mode, but the TFT with the highest electronic saturation mobility and on/off ratio 49.9 cm2 V s and 4.3× 108, respectively, are the ones in which the active and passive layers are amorphous. The ZnO TFT whose channel is based on polycrystalline ZnO, the mobility and on/off ratio are, respectively, 26 cm2 V s and 3× 106. This behavior is attributed to the fact that the electronic transport is governed by the s -like metal cation conduction bands, not significantly affected by any type of angular disorder promoted by the 2p O states related to the valence band, or small amounts of incorporated metal impurities that lead to a better control of vacancies and of the TFT off current. © 2007 American Institute of Physics.

This paper describes, for the first time, a method of producing polymorphous silicon (pm-Si:H) films by plasma-enhanced (PE) CVD, using an excitation frequency of 27.12 MHz. The aim is to produce, at high growth rates, nanostructured films that are more stable than the conventional amorphous or polymorphous silicon films grown by PECVD at 13.56 MHz. The processing data show that, at 27.12 MHz, the pm-Si:H films are produced close to the transition region from amorphous to microcrystalline silicon films, at a growth rate of about 0.3 nms-1, using pressures above 160 Pa. Apart from that, the analysis of the exodiffusion, spectroscopic ellipsometry (SE), and micro Raman data reveal that these films are more dense and compact than the polymorphous films grown at 13.56 MHz.

This paper deals with a new process to improve the stability of a-Si:H pin solar cells deposited in a single batch process by proper passivation of the interfaces. The process consists in removing partially a deposited sacrificial oxide layer grown between the p/i or i/n interfaces by SF6 etching. This layer is an absorber of defects and impurities that are introduced in the interfaces, mainly from the chamber walls and the substrate surface. The results achieved in laboratory samples lead to devices in which the fill factor and short circuit current density were improved respectively towards 75% and 16.5 mA cm-2, with a final working efficiency of about 9.5%. © 2001 Elsevier Science Ltd. All rights reserved.

This paper deals with the engineering aspects related to the rf energy coupling in Plasma Enhanced Chemical Vapour Deposition (PECVD) processes, in a diode-type unit in which an extra grid is used. The main emphasis is given in the determination of the real power delivered to the gas and comparing it with the total power losses, besides determining the best way to control the powder formed during the process. © 1994.

This paper describes a novel colorimetric method for detection of nucleic acid targets in a homogeneous format with improved sensitivity by means of a system based on the combination of a tunable monochromatic light source and an amorphous/nanocrystalline silicon photodetector that detects color and light intensity changes undergone by samples/assays containing tailored gold nanoparticles probes. This new low cost, portable, fast and simple optoelectronic platform, with the possibility to be re-used, permits detection of at least 400 fentomole of specific DNA sequences without target or signal amplification and was applied to the rapid detection of human pathogens in large variety of clinical samples such as Mycobacterium tuberculosis. © 2008 Elsevier B.V. All rights reserved.

The process conditions of growing thin silicon films by plasma enhanced chemical vapour deposition (PECVD) were presented. The plasma impedance was found to monitor the powders in the PECVD systems and good quality silicon films were grown close to the plasma regime where the powders were formed. The silicon films exhibited properties which were interpreted based on a two-phase model where silicon nanostructures were embedded in a disordered network.

Wide band gap microcrystalline silicon films have aroused considerable interest since they combine some electro-optical advantages of amorphous and crystalline materials highly important to produce electro-optical devices such as TFTs and solar cells. In this paper we present results concerning the electro-optical characteristics of highly transparent and conductive n-type μc-Si based films. Here, emphasis is given to the production of n-type μc-films with optical gaps of 2.3 eV and dark conductivity's of 6.5 Scm-1.

Silicon oxycarbide microcrystallinc layers, n- and p-doped, highly conductive and highly transparent have been produced using a Two Consecutive Decomposition and Deposition Chamber (TCDDC) system. The films exhibit suitable properties for optoelectronic applications where wide band gap materials with required conductivity and stability are needed. In this paper we present the role of partial oxygen pressure (po2) in controlling the composition, structure and transport properties (conductivity. δd and optical gap, Eop) of silicon oxycarbide microcrystalline layers. © 1994 Materials Research Society.

This paper presents results of the spatial and frequency detection limits of an integrated array of 32 one-dimensional amorphous silicon thin film position sensitive detectors with a nip structure, under continuous and pulsed laser operation conditions. The data obtained show that 0.45×0.06 cm arrays, occupying a total active area of about 1 cm2 have a spatial resolution better than 10 μm (modulation transfer function of about 0.2), with a cut-off frequency of about 6.8 KHz. Besides that, under pulsed laser conditions the device non-linearity has its minimum (about 1.6%), for a frequency of about 200Hz. Up to the limits of the cut-off frequency, the device non-linearity increases to values above 4%.

This paper deals with the determination of plasma impedance and ion density in r.f. plasmas using different mixtures of silane with methane or ethylene and r.f. powers. The aim is to correlate these parameters with carbon and hydrogen contents of the films produced. The data achieved show that the best carbon incorporation is achieved using ethylene gas mixtures, under low gas mixture concentration, where the substrate also sustains a low ion bombardment. The data also show that particulates in the plasma can be more easily formed in the ethylene-based processes. © 2001 Published by Elsevier Science B.V.

The aim of this work is to present a model able to explain the role of the lateral drift current on the experimental behaviour exhibited by p-i-n amorphous silicon solar cells (J-V characteristics, responsivity and the apparent device degradation behaviour), when the ratio between the covered and uncovered metal collected areas of the device is higher than one or recrystallization occurs in the edges of the p-i-n junction.

Here we report the performance of a selective floating gate (V GS) n-type non-volatile memory paper field-effect transistor. The paper dielectric exhibits a spontaneous polarization of about 1 mCm-2 and GIZO and IZO amorphous oxides are used respectively as the channel and the gate layers. The drain and source regions are based in continuous conductive thin films that promote the integration of fibres coated with the active semiconductor. The floating memory transistor writes, reads and erases the stored information with retention times above 14500 h, and is selective (for VGS > 5 ± 0.1 V). That is, to erase stored information a symmetric pulse to the one used to write must be utilized, allowing to store in the same space different information. © 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

This paper discusses the electron transport and the optical characteristics of amorphous indium zinc oxide and the role of the oxygen partial pressure on tailoring its properties. The data show that by varying the oxygen partial pressure during the deposition process from 10-3 to 2 × 10-1 Pa, the electrical resistivity varies from about 10-4 to 2 × 101 Ω cm, which corresponds to a variation on the Hall mobility from 60 to 10 cm2 V-1 s-1. The conductivity and mobility analysis show that the transport of carriers is not band tail limited, as happens in conventional disordered semiconductors, but highly dependent on the ionicity and the presence of oxygen vacancies, where mobility is mainly limited by carrier scattering. The optical characteristics inferred from the transmittance data reveal films with optical gaps in the range of 3.68-3.76 eV, very close to the ones observed on crystalline/polycrystalline IZO films (3.7-3.9 eV). © 2006 Elsevier B.V. All rights reserved.

The aim of this work is to present an analytical model which can to interpret the role of the collecting resistive layer on the static performances exhibited by 2D amorphous silicon hydrogenated p-i-n thin film position sensitive detectors. In addition, experimental results concerning the device linearity and spatial resolution are presented and checked against the predicted values of the analytical model proposed. © 1999 Elsevier Science S.A. All rights reserved.

This paper deals with the structure, composition and electro-optical characteristics of n-type amorphous and microcrystalline silicon thin films produced by plasma-enhanced chemical vapour deposition in a hydrogenhelium mixture. In addition, special emphasis is given to the role that hydrogen incorporation plays in the film's properties and in the characteristics of n-type microcrystalline films presenting simultaneously optical gaps of about 2·3 eV (controlled by the hydrogen content in the film), a dark conductivity of 6-5S cm-1 and a Hall mobility of about 0·86 cm2 V-1 s-1, the highest combined values for n-type microcrystalline silicon films, as far as we know.

The aim of this work is to provide the basis for the interpretation of the lateral photoeffect in p-i-n a-Si:H one-dimensional thin-film position-sensitive detectors (1D TFPSDs) under steady state, through an analytical model. The experimental data recorded in 1D TFPSD devices with different characteristics are compared with the predicted curves and the obtained correlations are discussed. © 1996.

This new production technique is based on the growth of a-Si films on a reactor where gas decomposition promoted by a capacitively coupled r. f. power system takes place in a chamber separated from that where amorphous films are deposited under the action of an electromagnetic static field. Using this method, we shall reduce films contamination caused by the residual gas desorbed from reactor walls. At the same time, there is a reduction plasma ion and electron damages on the deposited films. The main species impinging upon our substrates will be mainly composed of long life radicals with high mobilities and high diffusion rates, which will give origin to a random silicon network free of long poly-silane chains.

Today there is a strong interest in the scientific and industrial community concerning the use of biopolymers for electronic applications, driven mainly by low-cost and disposable applications. Adding to this interest, we must recognise the importance of the dream of wireless auto-sustained and low-energy-consumption electronics. This dream can be fulfilled by cellulose paper, the lightest and the cheapest known substrate material, as well as the Earth's major biopolymer and of tremendous global economic importance. Most of the paper used up to now is optimised in terms of the required mechanical and physical properties to be used as the support of inks of different origins. In the future, specific electronic heterogeneous paper sheets should be fabricated aiming to get paper fibers with required bulk and surface functionalities, proper water/vapour barrier, size and diameter/thickness of the fibrils and full paper thickness. This will be the function of components/devices to be incorporated/integrated such as thin-film transistors, complementary metal oxide semiconductor devices, passive electronic components (resistances, inductors and capacitors), memory transistors, electrochromics and thin-film paper batteries. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The electrosynthesis of polypyrrole (PPy) has been achieved on aluminium in aqueous medium of tartaric acid by means of cyclic voltammetry, potentiostatic and galvanostatic techniques. Scanning electron microscopy (SEM) and X-ray microanalysis by energy spectroscopy dispersion (EDS) applying on surfaces show that the PPy coating is developed from the metal surface through the cracks of the initial Al2O3 layer. A mechanism involving the participation of the supporting electrolyte and the pyrrole (Py) in distinct active sites was proposed based on the linear sweep voltammetry. It is observed for all applied electrochemical techniques that the pyrrole concentration has to be higher than 0.1 M to allow the polypyrrole electrodeposition in acid medium. Scanning electron microscopy, secondary electrons (SE) and backscattering electrons (BE), shows that the PPy coating obtained in galvanostatic and potentiostatic modes starts with small islands at weak applied potentials or current densities. Moreover, EDS reveals a good homogeneity and compactness of the film achieved in galvanostatic method. The corrosion results in 3% NaCl medium show that the PPy coating decreases the corrosion behaviour of the aluminium. The bilayer Al2O3/PPy shows a capacitor with future applications. © 2006 Elsevier Ltd. All rights reserved.

In this paper we present results concerning the performance exhibited by an integrated array of 32 one-dimensional amorphous silicon thin film position sensitive detectors based on nip and hetero amorphous silicon structures, with a total active area size below 1 cm2 linearity, its spatial resolution and response time, that make it one of the most interesting analog detector to be used in unmanned optical inspection control systems where a continuous detection process is required. This opens a wide range of applications for amorphous silicon devices in the area of image processing. © 2002 Elsevier Science B.V. All rights reserved.