Phosphogypsum (PG) is a pollutant residue resulting from the production of phosphoric acid in the phosphated fertilizers industry. About 180 millions of tons of PG are generated worldwide per year, which originates storage problems because of the environmental restrictions and the high costs of storage spaces. Taking into account the mineralizer properties of PG it has been studied a way to valorize this residue as an alternative material in the production of Portland cement clinker. The PG and the raw-materials (limestone, marl, sand and iron oxide) were chemical, mineralogical and thermally characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD) and differential thermal analysis and termogravimetric analysis (DTA/TGA). After milling, the phosphogypsum was mixed with the raw-materials in different amounts up to 10% weight. The raw mixtures were submitted to two types of firing schedules, heating up to 1500°C without any holding time or heating up to 1350°C and holding for 20 minutes. After firing, the clinkers were analyzed by optical microscopy, milled and characterized in terms of chemical and mineralogical compositions. The clinkers were used to produce cement mortar according to NP EN 196-1 standard. The resultant test specimens were mechanically tested at 2 and 28 days according to the same standard. The obtained results show a reduction of about 140°C in the clinkerization temperature, when a raw mixture with 5% phosphogypsum was used. Standard clinkers, without phosphogypsum addition, which were fired at 1500°C, originated test specimens with a compressive strength of 48.1MPa at 28 days. Test specimens produced with clinker containing 5% phosphogypsum present higher compressive strength values at 28 days, being 55.1MPa for clinkers produced at 1500°C, and 49.4 MPa for clinkers produced at 1350°C. © (2013) Trans Tech Publications, Switzerland.

Li2O-BaO-Al2O3-La2O 3-P2O5 glasses optically activated with rare earth ions with the 4f5, and 4f8 electronic configuration (Sm3+ and Tb3+, respectively) were analyzed by Raman spectroscopy, absorption, excitation photoluminescence, decay curves and temperature dependent photoluminescence. The spectroscopic characteristics of the as-prepared and heat treated samples at temperatures below and above T g were studied as well as their room temperature photometric properties under ultraviolet excitation. All the doped glasses exhibit typical signatures of the lanthanides in their trivalent charge state. For the samarium doped glass heat treated at 250 C (<Tg) the Sm2+ luminescence was also observed. The analysis of the luminescence efficiency was performed in the interval range of 14 K to room temperature, where the integrated intensity of the luminescence was found to decrease for the Sm 3+ and Tb3+ ions in the studied temperature range. Luminescence decay curves were found to be non-exponential for the 4G5/2 → 6H7/2 and 5D3 → 7F4 transitions of the Sm3+ and Tb3+ ions, respectively. The results strongly suggest the occurrence of energy transfer processes through cross relaxation phenomena, mediated by dipole-dipole interaction in all the studied samples. The decay of the 5D4 → 7F5 emission of the Tb3+ ions was found to be single exponential with a time constant of ∼3.1 ms. Based on the spectroscopic characteristics, models for recombination processes are proposed. The room temperature luminance photometric properties with ultraviolet excitation show that the samarium doped glasses have much lower luminance intensity (around 0.3 Cd/m2) when compared with the 6-7 Cd/m2 observed for the terbium doped ones. © 2013 Elsevier B.V. All rights reserved.

Hydroxyapatite [Hap; Ca10(PO4)6(OH)2) and b-tricalcium phosphate [b-TCP; Ca3(PO4)2] are biocompatible calcium phosphates used in skeletal surgery. The natural HAp is one of the main components of bone and, as a synthetic material, has been widely used for bone replacement presenting good bioactivity. Nevertheless synthetic HAp presents a slow in vivo degradation rate which is disadvantageous for bone’s reparative process. b-TCP has also good osteogenic characteristics presenting the ability to form strong bonds with the bone however, its degradation rate is too fast [1]. Therefore, a composite combining these two ceramics is valuable as it exhibits a suitable degradation rate. Because of the piezoelectric properties of bone it is known that electrical polarization of calcium phosphates can enhance the bioactivity and biointegration of implants [2]. Previous studies have already showed that HAp/b-TCP ceramics can be electrically polarized and that electrical polarization enhances osteogenesis in the early stage of the implantation process. However further studies are required to understand, optimize and improve the polarization technique [1]. In this work a commercial biphasic ceramic powders were pressed in a mold at 200 MPa to produce disc shaped samples. Afterwards, the samples were sintered at temperatures from 950ºC to 1150ºC and the influence of the heat treatment in the electrical polarization and subsequent bioactivity was investigated. The samples were polarized under a high DC electric field at relatively lower temperature (200oC) compared to previous studies and the stability of polarization was tested using TSDC (thermally depolarization currents) measurements. It was studied the influence of the water, initially present in the material, in the total charge deposited during polarization, its stability and its relation with heat treatment after pressing. The influence of the addition of b-TCP on sample’s stored charge was also evaluated. Finally bioactivity tests in a simulated body fluid solution were made taking into account the signal of the charge in each surface of the disc samples so that the results could be compared to previous ones.

{Aluminophosphate glasses belonging to the Li2O-BaO-Al 2O3- La2O3-P2O 5 system doped with Tb3+ were prepared and investigated. Methods as Induced Coupled Plasma-Mass Spectrometry (ICP-MS), Induced Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES) and X-ray diffraction (XRD) have been used to establish the elemental composition of these vitreous materials. The influence of the Tb3+ ions on the optical properties of the phosphate glasses has been investigated in relation with the structural characteristics of the vitreous matrix. The optical behavior has been studied by ultra-violet-visible (UV-Vis) spectroscopy, revealing electronic transitions specific for terbium ions. Fluorescence spectroscopy measurements have been performed by excitation in the UV and visible domains (377 nm and 488 nm) which resulted in the most significant fluorescence peaks in the Vis domain (540 and 547 nm). Structural information via vibration modes were provided by Fourier Transform Infrared (FTIR) absorption spectra in the 400-4000 cm-1 range. Absorption peaks specific for the vitreous phosphate matrix were put in evidence as P-O-P symmetrical and asymmetrical stretching vibration modes, P-O-P bend, PO2- symmetrical and asymmetrical stretching vibration modes

Marinobacter hydrocarbonoclasticus is a marine bacterium widespread in the Mediterranean sea and Atlantic Ocean, and growing at temperate temperatures. This bacterium can perform complete denitrification, reducing nitrate to molecular nitrogen under anaerobic conditions. Here the nitrite concentration, pH and nitrous oxide reductase activity was monitored during bacterial growth, showing that this bacterium can also perform complete denitrification under low oxygen tension, using lactate as carbon source, in the presence of nitrate as alternative electron acceptor. Nitrous oxide reductase activity was observed after 7 h of growth under low oxygen tensions, and is maintained constant after 48h. Nitrite concentration reaches its maximum at mid-exponential phase and in the stationary phase, at lower oxygen tensions is almost non-existent.

Purpose - The purpose of this paper is to examine how different business models, embodied in awards, standards and frameworks, can contribute to modelling a lean and green approach for an organization and its supply chain. Design/methodology/approach - In total, 12 business models were studied. A literature review was conducted to provide a comprehensive understanding of each model. After defining lean and green management paradigms, a number of guidelines were developed to connect and integrate lean and green principles. Findings - The study reveals a number of categories that are common in most business models, providing adequate conditions for a lean-green transformation. The guidelines were developed to model a lean-green organization by applying specific principles and tools of a lean and green culture. Research limitations/implications - The relationships identified within and between models reflect a partial view of a lean-green transformation. The approach adopted merges the different principles, and tends to emphasize similarities and minimize differences. Practical implications - The proposed model can be the basis for further research in lean and green paradigms, contributing to understanding when an organization and its supply chain can apply the lean and green principles and tools. Originality/value - This study is the first attempt to understand, develop and integrate a lean and green organizational culture approach, based in standardized management business models.