abstract Vermilion red, mercury sulphide (a-HgS), was one of the most important reds in art and its use as a pigment dates back to Antiquity. In medieval Europe, it could be mined as cinnabar, or produced as vermilion by heating mercury with sulphur. This work aims to study the production of synthetic vermilion as a medieval pigment and to confirm which was the source (mineral or artificial) of the reds used in Portuguese medieval illuminations. The production of synthetic vermilion was based on the process described in the Judaeo-Portuguese medieval treatise “The book on how to make colours”, using materials and technologies as close as possible to the medieval ones. The reaction mechanism was studied by following the heating process by X-ray diffraction, and it was possible to conclude that the transformation from black cubic b-HgS into red hexagonal a-HgS is a solid-state phase transition, occurring at 235 ?C. This result is contrary to what published in technical art literature, in which this process is described as a sublimation. Moreover, Scanning Electron Microscopy evidenced a sinterization effect on the artificial vermilion, not found in medieval original samples nor in paints prepared with mineral cinnabar from Almadén (Spain). Red mercury sulphide, natural and synthetic,was then prepared as a parchment-glue paint and compared to proteinaceous red paints from 12the13th century minia- tures produced in important medieval monasteries, previously fully characterized by a multi-analytical approach (m-Energy dispersive X-ray fluorescence, m-Fourier Transform Infrared Spectroscopy, Raman microscopy). A comparative Electron probe microanalysis of the red paints point to amineral provenance for medieval vermilion found in Portuguese illuminations

The wind energy production is a growing industry and the energy produced is renewable and environmentally cleaner than most of the energy production systems. The supports of the wind energy generators may be built with precast concrete elements. The precast solutions for these structures are competitive in comparison to other structural systems. The evolution of the technology for wind energy production shows a clear need for larger wind turbines and longer blades and, consequently, taller towers. The experience also shows that precast concrete solutions increase their competitiveness as the tower height increases. Offshore wind farms have some advantages in relation to onshore ones, which explains recent investments in this area. Also in this case, the durability of concrete in the sea when compared to steel, gives advantages to precast concrete in relation to other structural solutions. This paper shows the evolution of the supports of the wind energy generators and the advantages of the use of precast concrete towers.

The orange protein (ORP) isolated from the sulfate-reducing bacterium Desulfovibrio gigas (11.8 kDa) contains a mixed-metal sulfide cluster of the type [S2MoS2CuS2MoS2](3-) noncovalently bound to the polypeptide chain. The D. gigas ORP was heterologously produced in Escherichia coli in the apo form. Different strategies were used to reconstitute the metal cluster into apo-ORP and obtain insights into the metal cluster synthesis: (1) incorporation of a synthesized inorganic analogue of the native metal cluster and (2) the in situ synthesis of the metal cluster on the addition to apo-ORP of copper chloride and tetrathiomolybdate or tetrathiotungstate. This latter procedure was successful, and the visible spectrum of the Mo-Cu reconstituted ORP is identical to the one reported for the native protein with absorption maxima at 340 and 480 nm. The (1)H-(15)N heteronuclear single quantum coherence spectra of the reconstituted ORP obtained by strategy 2, in contrast to strategy 1, exhibited large changes, which required sequential assignment in order to identify, by chemical shift differences, the residues affected by the incorporation of the cluster, which is stabilized inside the protein by both electrostatic and hydrophobic interactions.

This paper presents a domain-specific querying language for model-driven spreadsheets. We briefly show the design of the language and present in detail its implementation, from the denormalization of data and translation of our user-friendly query language to a more efficient query, to the execution of the query using Google. To validate our work, we executed an empirical study, comparing QuerySheet with an alternative spreadsheet querying tool, which produced positive results.

These tutorial notes present a methodology for spreadsheet engineering. First, we present data mining and database techniques to reason about spreadsheet data. These techniques are used to compute relationships between spreadsheet elements (cells/columns/rows). These relations are then used to infer a model defining the business logic of the spreadsheet. Such a model of a spreadsheet data is a visual domain specific language that we embed in a well-known spreadsheet system. The embedded model is the building block to define techniques for model-driven spreadsheet development, where advanced techniques are used to guarantee the model-instance synchronization. In this model-driven environment, any user data update as to follow the the model-instance conformance relation, thus, guiding spreadsheet users to introduce correct data. Data refinement techniques are used to synchronize models and instances after users update/evolve the model. These notes briefly describe our model-driven spreadsheet environment, the MDSheet environment, that implements the presented methodology. To evaluate both proposed techniques and the MDSheet tool, we have conducted, in laboratory sessions, an empirical study with the summer school participants. The results of this study are presented in these notes.

n/a

n/a

This paper presents a micro power light energy harvesting system for indoor environments. Light energy is collected by amorphous silicon photovoltaic (a-Si:H PV) cells, processed by a switched capacitor (SC) voltage doubler circuit with maximum power point tracking (MPPT), and finally stored in a large capacitor. The MPPT fractional open circuit voltage (V-OC) technique is implemented by an asynchronous state machine (ASM) that creates and dynamically adjusts the clock frequency of the step-up SC circuit, matching the input impedance of the SC circuit to the maximum power point condition of the PV cells. The ASM has a separate local power supply to make it robust against load variations. In order to reduce the area occupied by the SC circuit, while maintaining an acceptable efficiency value, the SC circuit uses MOSFET capacitors with a charge sharing scheme for the bottom plate parasitic capacitors. The circuit occupies an area of 0.31 mm(2) in a 130 nm CMOS technology. The system was designed in order to work under realistic indoor light intensities. Experimental results show that the proposed system, using PV cells with an area of 14 cm(2), is capable of starting-up from a 0 V condition, with an irradiance of only 0.32 W/m(2). After starting-up, the system requires an irradiance of only 0.18 W/m(2) (18 mu W/cm(2)) to remain operating. The ASM circuit can operate correctly using a local power supply voltage of 453 mV, dissipating only 0.085 mu W. These values are, to the best of the authors' knowledge, the lowest reported in the literature. The maximum efficiency of the SC converter is 70.3 % for an input power of 48 mu W, which is comparable with reported values from circuits operating at similar power levels.

This paper presents a micro power light energy harvesting system for indoor environments. Light energy is collected by amorphous silicon photovoltaic (a-Si:H PV) cells, processed by a switched capacitor (SC) voltage doubler circuit with maximum power point tracking (MPPT), and finally stored in a large capacitor. The MPPT fractional open circuit voltage (V-OC) technique is implemented by an asynchronous state machine (ASM) that creates and dynamically adjusts the clock frequency of the step-up SC circuit, matching the input impedance of the SC circuit to the maximum power point condition of the PV cells. The ASM has a separate local power supply to make it robust against load variations. In order to reduce the area occupied by the SC circuit, while maintaining an acceptable efficiency value, the SC circuit uses MOSFET capacitors with a charge sharing scheme for the bottom plate parasitic capacitors. The circuit occupies an area of 0.31 mm(2) in a 130 nm CMOS technology. The system was designed in order to work under realistic indoor light intensities. Experimental results show that the proposed system, using PV cells with an area of 14 cm(2), is capable of starting-up from a 0 V condition, with an irradiance of only 0.32 W/m(2). After starting-up, the system requires an irradiance of only 0.18 W/m(2) (18 mu W/cm(2)) to remain operating. The ASM circuit can operate correctly using a local power supply voltage of 453 mV, dissipating only 0.085 mu W. These values are, to the best of the authors' knowledge, the lowest reported in the literature. The maximum efficiency of the SC converter is 70.3 % for an input power of 48 mu W, which is comparable with reported values from circuits operating at similar power levels.

Trace elemental content was analysed in edible tissues of Mytilus galloprovincialis collected in five different sampling areas near the mouth of river Tagus estuary in Lisbon. The concentrations of essential elements (S, K, Ca, Fe, Cu, Zn, As, Br and Sr) were determined by energy-dispersive X-ray fluorescence (EDXRF) spectrometry, while toxic elements (Cr, Cd, Hg, Se and Pb) were measured by inductively coupled plasma-atomic emission spectrometry (ICP-AES). The results show that the essential elements K and S are present at the highest concentrations in all the studied samples reaching 2,920 and 4,520 μg g(-1) (fresh weight), respectively. The highest levels of heavy metals found were in two areas close to the city for Pb and Cd, but below the maximum allowed values.

We have measured the x-ray spectra from highly charged Si, S and Cl ions in collisions with thin foils using a high-resolution x-ray spectrometer. The observed lines have been assigned to various transitions in H-, He- and Li-like ions. For proper identification of line positions, the theoretical calculations have been carried out using a state-of-the-art MCDF code including QED effects, with which the experimental data is in excellent agreement. We have also observed, for the first time, x-rays arising out of the decay of long-lived resonant states in the He-like ions of each species. Details will be presented.

Systems externally reinforced by bonded fibre reinforced polymers (FRP) are widely used in the retrofitting and strengthening of reinforced concrete (RC) structures. A drawback of the usage of this technique lies on the uncertainty of the long term behaviour of those reinforcements. Researchers have paid heed to this aspect and a number of tests and alternative techniques have recently been described. An experimental programme developed to supplement work of the authors recently published and which focused on specimens not submitted to aggressive environments is described. The specimens used have the same geometry as in the previous paper, but they were exposed to salt fog cycles and dry/wet cycles with salt water for periods of 3000 h, 5000 h and 10,000 h. The interface of the glass fiber polymeric composite (GFRP)-to-concrete was characterized after the systems underwent such aggressive conditions. The GFRP wrap comprised of two layers and wet lay-up technique was used on its preparation and application. The cohesion and friction angle for GFRP-to-concrete interfaces were measured tat selected stages of ageing process and envelope failure laws were obtained based on the Mohr–Coulomb failure criterion. Changes of 27% in cohesion and 8% in the friction angle were found due to the attack of the interface and consequences of the changes are examined.