Over the last decades, several indices based on ash chemistry and ash fusibility have been used to predict the ash behaviour during coal combustion, namely, its tendency for slagging and fouling. However, due to the physical–chemical differences between coals and biomass, in this work only the applicability of an ash fusibility index (AFI) to the combustion and co-combustion of three types of biomass (straw pellets, olive cake and wood pellets) with coals was evaluated. The AFI values were compared with the behaviour of ash during combustion in a pilot fluidized bed and a close agreement was observed between them. For a better understanding of the mechanisms associated with bed ash sintering, they were evaluated by SEM/EDS and the elements present on the melted ash were identified. Evidences of different sintering mechanisms were found out for the fruit biomass and herbaceous biomass tested, depending on the relative proportions of problematic elements. The particles deposited on a fouling probe inserted in the FBC were analyzed by XRD and the differences between the compounds identified allowed concluding that the studied biomasses present different tendencies for fouling. Identification of KCl and K2SO4 in the deposits confirmed the higher tendency for fouling of fruit biomass tested rather than wood pellets.

Clavicles and interclavicles are plesiomorphically present in Reptilia. However, several groups show reduction or even loss of these elements. Crocodylimorpha, e.g., lost the clavicles, whereas dinosaurs are generally interpreted to only preserve the clavicles, the theropod furcula representing an unique case of fused clavicles. In sauropods, reports of clavicles are relatively frequent in non-titanosauriforms. These elements are elongated, curved, and rather stout bones with a spatulate and a bifurcate end. However, they were always found as single bones, and differ from the relatively short and unbifurcated clavicles found articulated with the scapulae of basal sauropodomorphs.
Elements from the Howe Quarry (Late Jurassic; Wyoming, USA) shed new light on these interpretations. Besides the elongated, curved bones (herein named morphotype A), also pairs of symmetric, L-shaped bones were recovered (morphotype B), associated with diplodocid dorsal and cervical vertebrae. Elements resembling morphotype B - articulated between the scapulae - have recently been reported from a diplodocid found near Tensleep, Wyoming. Taphonomic evidence, as well as the fact that they were preserved in symmetrical pairs, therefore implies that morphotype B represents the true sauropod clavicles.
Contrary to earlier reports, morphotype A elements from the Howe Quarry, as well as of previously reported specimens show a symmetry plane following the long axis of the elements. It is thus possible that the morphotype A elements were single bones from the body midline. The only such element present in the pectoral girdle of tetrapods are the interclavicle and the furcula. Comparison with crocodilian and lacertiform interclavicles indicates that the bifurcate end of the sauropod elements might represent the reduced transverse processes of the anterior end, and the spatulate end would have covered the coracoids or sternal plates ventrally.
The presence of both clavicles and interclavicles in the pectoral girdle stiffens the anterior trunk, and enhances considerably its stability. Such an enforcement might have been needed in diplodocids due to the strong lateral forces induced to the fore-limbs by the posteriorly placed center of mass (due to shorter fore- than hind-limbs), as well as lateral movements of the enormously elongated necks and tails. The absence of clavicles and interclavicles in titanosauriforms coincides with the development of wide-gauge locomotion style.
The presence of interclavicles in sauropods supports the recently proposed homology of the furcula with the interclavicle, instead of representing fused clavicles. Interclavicles were thus not lost, but may have remained cartilaginous or have yet to be found in basal dinosauriforms.

Since the 1980’s, several buildings throughout the world have been subject to gas explosions, impact by cars or airplanes, or car bomb attacks. In many cases the effect of the impact or explosion has been the failure of a critical structural member at the perimeter of the building. After the failure, the load supported by that member could not be redistributed and part or all of the structure has collapsed in a progressive manner. The phenomenon that occurs when local failure is not confined to the area of initial distress, and spreads horizontally and/or vertically through the structure, is termed progressive collapse.

Progressive collapse is a relatively rare event, as it requires both an accidental action to cause local damage and a structure that lacks adequate continuity, ductility, and redundancy to prevent the spread of damage. It is technically very difficult and economically prohibitive to design buildings for absolute safety. However it is possible to construct precast concrete buildings that afford an acceptable degree of safety with regard to accidental actions.

A structure is normally designed to respond properly, without damage, under normal load conditions, but local and/or global damages cannot be avoided under the effect of an unexpected, but moderate degree of accidental overload. Properly designed and constructed structures usually possess reasonable probability not to collapse catastrophically under such loads, depending on different factors, for example: the type of loading; the degree and the location of accidental loading in regard to the structure and its structural members; the type of structural system, the construction technology, and the spans between structural vertical members, etc.

No structure can be expected to be totally resistant to actions arising from an unexpected and extreme cause, but it should not be damaged to an extent that is disproportionate to the original cause.

The aim of fib Bulletin 63 is to summarize the present knowledge on the subject and to provide guidance for the design of precast structures against progressive collapse. This is addressed in terms of (a) the classification of the actions, (b) their effect on the structural types, (c) the strategies to cope with such actions, (d) the design methods and (e) some typical detailing, all supplemented with illustrations from around the world, and some model calculations.

n/a

n/a

Supply chains (SCs) may experience instability induced by disturbances such as extreme climate conditions or accidents. These events can cause severe negative effects on SCs, jeopardising the on-time delivery of products and services to customers. This paper proposes a mapping framework to improve SC resilience to such events, avoiding possible failure modes. The proposed mapping framework allows identification of the current SC operation and possible transition states, together with points of vulnerability. An illustrative example of the framework applied to a real-life wine SC is presented.

n/a

Mass balances of ash and potassium for a fluidized bed combustor were performed incorporating measurement uncertainties. The total output mass of ash or a chemical element should be equal to the mass in the input fuel; however, this is not often achieved. A realistic estimation of recovery uncertainty can support the reliability of a mass balance. Estimation of uncertainty helps to establish a reliable evaluation of the recovery ratio of ash mass and elemental mass. This may clarify whether any apparent lack in closing the mass balance can be attributed to uncertainties. The evaluation of measurement uncertainty for different matrices, namely coal, biomass, sand and ashes from different streams was based on internal quality control data and external quality control data, namely analysis of samples from proficiency tests or use of a certified reference material. The evaluation of intermediate precision and trueness allowed the estimation of measurement uncertainty. Due to the different physic and chemical characteristics of the studied matrices, the uncertainty of precision was evaluated using R-charts of data obtained from the analysis of duplicates for the majority of samples. This allowed evaluating sample heterogeneity effects. The instrumental acceptance criterion was also considered and included in the combined uncertainty. The trueness was evaluated using data from several proficiency tests and from analysis of a certified reference material or sample spiking. Statistically significant bias was included.

Three species of biomass origin (straw pellets, olive cake and wood pellets) and two coals from different countries (Coal Polish and Coal Colombian) have been studied to understand the fate of their ash forming matter during the combustion process and to investigate the influence of co-firing biomass with coal. Three different approaches to investigate the ash behaviour were employed: (1) chemical fractionation analysis to evaluate the association/reactivity of ash forming elements in the fuels as a prediction tool, (2) establishment of elements partitioning in ash streams produced in the combustion and co-combustion trials, and (3) evaluation of enrichment factors of elements in the ash streams. The chemical fractionation analysis was applied to all fuels used to evaluate how the association/reactivity of elements making up ash may influence their behaviour during combustion. Combustion tests were carried out on a pilot scale fluidized bed combustor (FBC). Four ash streams were obtained at different locations. The uncertainty of measurements was estimated allowing a critical evaluation of mass balances over the combustion system and the partitioning of elements in the ash streams. The enrichment factors of elements in the several ash streams were estimated, incorporating uncertainties associated with analytical measurements. Results obtained showed that for FBC the relation between the chemical fractionation and the experimental partitioning is strongly affected by elutriation of particles. The element enrichment factor estimated for each ash stream, using Al as a reference element, revealed better correlations with the elements reactivity obtained by chemical fractionation because it overcomes particles elutriation effects. Nevertheless, it was observed that the reactivity estimated by chemical fractionation could not be solely interpreted as tendency of the elements to volatilize on FBC system, as reaction in bed zone of boiler may also occur retaining reactive elements.

A gene encoding Bfr (bacterioferritin) was identified and isolated from the genome of Desulfovibrio vulgaris cells, and overexpressed in Escherichia coli. In vitro, H2O2 oxidizes Fe2+ ions at much higher reaction rates than O-2. The H2O2 oxidation of two Fe2+ ions was proven by Mossbauer spectroscopy of rapid freeze-quenched samples. On the basis of the Mossbauer parameters of the intermediate species we propose that D. vulgaris Bfr follows a mineralization mechanism similar to the one reported for vertebrate H-type ferritins subunits, in which a diferrous centre at the ferroxidase site is oxidized to diferric intermediate species, that are subsequently translocated into the inner nanocavity. D. vulgaris recombinant Bfr oxidizes and stores up to 600 iron atoms per protein. This Bfr is able to bind DNA and protect it against hydroxyl radical and DNase deleterious effects. The use of H2O2 as an oxidant, combined with the DNA binding and protection activities, seems to indicate a DPS (DNA-binding protein from starved cells)-like role for D. vulgaris Bfr.