We report in this paper the influence of the rf power on the properties of p-type silicon thin films produced by hot wire plasma assisted chemical vapor deposition (HWPA-CVD) technique, using a gas mixture containing SiH4, B2H6, CH4 and H2. The influence of the rf power in the film morphology, its structure and its composition has been determined by means of scanning electron microscopy (SEM), X-ray diffraction (XRD) and infrared spectroscopy. The electrical dark conductivity, activation energy, optical band gap and growth rate values for the different rf power was also evaluated. The data achieved show that rf power rules the surface morphology, the film structure and its electrical characteristics. © 2001 Elsevier Science B.V. All rights reserved.

This paper presents the process conditions that lead to the production of nanostructured silicon films grown by plasma enhanced chemical vapour deposition close to the so-called gamma regime (powder formation), highly dense and with low density of bulk states. Thus, the powder management is one important issue to be addressed in this paper. As a general rule we observed that high quality films (low density of states and high μτ products) are obtained when films are grown under low ion bombardment at high hydrogen dilution and deposition pressure conditions, to allow the proper surface passivation and surface activation.

In this work we present the results of a study on the uniformity of ZnO thin films produced by spray pyrolysis. The properties of the thin films depend essentially on the carrier gas pressure and gas flow used. The best films for optoelectronic applications were obtained with a carrier gas pressure of 2 bar and solution flow of 37 ml/min. The velocity of the nozzle affects essentially the uniformity of the ZnO thin films. However this important characteristic of the large area thin films is independent of the nature (doped and undoped) of the thin film and exhibits a high dependence on the variation of the temperature along the substrate. © 2001 Materials Research Society.

The performances of amorphous and nano-crystalline porous silicon thin films as gas detector are pioneer reported in this work. The films were produced by the hot wire chemical vapour deposition (HW-CVD). These films present a porous like-structure, which is due to the uncompensated bonds and oxidise easily in the presence of air. This behaviour is a problem when the films are used for solar cells or thin film transistors. For as gas detectors, the oxidation is a benefit, since the CO, H2 or O2 molecules replace the OH adsorbed group. In the present study we observe the behaviour of amorphous and nano-crystalline porous silicon thin films under the presence of ethanol, at room temperature. The data obtained reveal a change in the current values recorded by more than three orders of magnitude, depending on the film preparation condition. This current behaviour is due to the adsorption of the OH chemical group by the Si uncompensated bonds as can be observed in the infrared spectra. Besides that, the current response and its recover time are done in few seconds.

Flexible large area thin film position sensitive detectors based on amorphous silicon technology were prepared on polyimide substrates using the conventional plasma enhanced chemical vapor deposition technique. The sensors were characterized by spectral response, illuminated I-V characteristics position detectability measurements and atomic force microscopy. The obtained one-dimensional position sensors, 5-mm wide and 60-mm long, presented a maximum spectral response at 600 nm, an open circuit voltage of 0.6 V and a position detectability with a correlation of 0.9989 associated to a S.D. of 1×10-2, comparable to those produced on glass substrates.

Coal fly ashes produced by an extinguished power plant in the north of Portugal have been melted with addition of CaCO3 and Na2CO3 to obtain glasses. One of the formulated compositions was selected for further studies and it was possible to manufacture glass-ceramics by crystallizing the parent glass through adequate time-temperature schedules. The macroscopic appearance, microstructure, mechanical, thermal and chemical properties indicated that these materials are quite attractive for cladding applications, exhibiting in some cases better performances than the conventional ceramic tiles.

In this work, we present the properties of n-type silicon films obtained by hot wire plasma assisted technique produced at different rf power and gas flow rate. The films were produced at a filament temperature of 2000°C and the rf power was varied from 0 W to 200 W while gas flow rate was varied from 15 to 100 sccm keeping rf power at 50 W. In this flow rate range, the growth rate of the films varied from 5Å/s to 250Å/s and the corresponding electrical room dark conductivity varied from 10-2 to 10(Ωcm)-1. On the other hand, we observed that the electrical conductivity increased from 2 to 6(Ωcm)-1, and the Hall mobility from 0.1 to 2 cm2/V.s as rf power change from 0 W to 200 W. The infrared, EDS and XPS analyses revealed the existence of oxygen incorporation, which is not related to post-deposition oxidation. The X-ray diffraction and μRaman data show the presence of Si crystals in the films structure and the SEM micrographs reveal a granular surface morphology with grain sizes lower than 60 nm.