n/a

Cross-linked polyethylene (XLPE) is currently widely used as an insulating material for power cables due to its good physical properties, however when in use it undergoes an electrical ageing process. Its ability to trap electric charge can give rise to space charge accumulation in the bulk of the polymer and produce localised electric stresses that can lead to cable failure, since the electric field will be increased above the design stress in some regions favouring the initiation of degradation there. In this work the PEA (pulsed electro-acoustic) method was used to compare the charge dynamics in three samples (XLPE cable peelings) aged in different ways (electrothermally in the laboratory, field aged in service and thermally aged in the laboratory). Very different transient behavior was found depending upon the ageing history. This is related to differences in the migration of chemical species in the insulation layer, which are known to act as charge traps. All materials showed heterocharge peaks when the space charge reached stability, the magnitude of which seems to be related to the severity of the ageing. (c) 2007 Elsevier B.V. All rights reserved.

Amorphous silicon carbide films were obtained by plasma enhanced chemical vapor deposition (PECVD) technique using a gas mixture of silane, methane, and hydrogen with a high excitation frequency and a high hydrogen dilution ratio. The high temperature annealing behavior of the amorphous silicon carbide films was studied by annealing at 1373 K for 1 h in nitrogen atmosphere. A very thin Au film was deposited on part of the films to investigate the metal induced crystallization effect. Well aligned nanotubes were found on the silicon carbide films covered by a thin gold layer after the high temperature annealing by atomic force microscopy. Further study is necessary to identify the nature of the nanotubes and elucidate their growth mechanism. © 2006 Elsevier B.V. All rights reserved.

Diphasic silicon films (nc-Si/a-Si:H) have been prepared by a new regime of plasma enhanced chemical vapour deposition in the region adjacent of phase transition from amorphous to microcrystalline state. Comparing to the conventional amorphous silicon (a-Si:H), the nc-Si/a-Si:H has higher photoconductivity (σph), better stability, and a broader light spectral response range in the longer wavelength range. It can be found from Raman spectra that there is a notable improvement in the medium range order. The blue shift for the stretching mode and red shift for the wagging mode in the IR spectra also show the variation of the microstructure. By using this kind of film as intrinsic layer, a p-i-n junction solar cell was prepared with the initial efficiency of 8.51% and a stabilized efficiency of 8.01% (AM1.5, 100 mw/cm2) at room temperature. © 2006.

A series of amorphous silicon carbide films were prepared by plasma enhanced chemical vapor deposition technique on (100) silicon wafers by using methane, silane, and hydrogen as reactive resources. A very thin (around 15 Å) gold film was evaporated on the half area of the a-SiC:H films to investigate the metal induced crystallization effect. Then the a-SiC:H films were annealed at 1100°C for 1 hour in the nitrogen atmosphere. Fourier transform infrared spectroscopy (FTIR), X-Ray diffraction (XRD), and scanning electron microscopy (SEM) were employed to analyze the microstructure, composition and surface morphology of the films. The influences of the high temperature annealing on the microstructure of a-SiC:H film and the metal induced metallization were investigated.

This work deals with the study of the role of the film thickness and composition on the color selectivity of the collecting spectrum of glass/ZnO:Ga/p-a-Si1-xCx:H/ a-Si1-x C x:H /a-Si:H/n-a-Si:H/Al photoelectronic detectors produced in a single chamber plasma enhanced chemical vapor deposition (PECVD) system. The cross contaminations were minimized by a rotate-cover substrate holder system. The devices can detect the blue illumination at small reverse bias and detect red illumination at large reverse bias. The role of the process parameters, especially the thickness of the p-type and intrinsic a-Si1-x C x:H, and the intrinsic a-Si:H layers on the device performances were studied in detail aiming to achieve a better detectivity. © 2005 Materials Research Society.