The concept of functionally graded material (FGM), may be considered as a model particularly interesting to be applied in components for the automotive industry, if reliability and cost can be controlled in an advantageous way. In fact, coupling superior superficial wear resistance with a significant bulk toughness, without compromising important weight savings, by using Al-Si metal matrix composites (MMC’s) selectively reinforced at the surface with SiC particles, is likely to be considered as a innovative advance to that industrial field, if adequate production techniques are developed. Casting under a centrifugal force may well be considered as one of the most effective methods for processing Al-based FGM´s. A primary problem to be faced when producing MMC´s reinforced with ceramic particles is related with the imperfect wetting of the ceramic particles by the molten matrix alloy. A first consequence of defective wetting may be the formation of ceramic-ceramic, ceramic-gas and/or metal-gas interfaces, instead of the desired metal-ceramic interface. Secondly, wetting phenomena play an essential role regarding the physical, chemical and mechanical characteristics of the metal/ceramic interface. A general consequence of these aspects may be related with the degradation of the material properties, be it mechanical, chemical, or thermal in nature. The present work refers to an X-ray microtomography experiment aiming at the elucidation of some aspects regarding particle distribution in SiCp-reinforced functionally graded aluminium composites. Precursor composites were produced by rheocasting. These were then molten and centrifugally cast in order to produce the FGM composites. From these, small cylindrical samples were extracted and observed by X-ray microtomography at the European Synchrotron Radiation Facility (ESRF). The 3D tomographic images were obtained in edge-detection mode (phase-contrast mode), and an adequate segmentation procedure was employed to isolate the pores and SiC particles from the Al matrix. This has allowed a study of the relations between the matrix, the SiC particles, and locally intervening porosities of varying shapes, aiming at a better understanding of the mechanisms involved.

A novel iron(III) porphyrin disulphide derivative have been successfully immobilised on gold surfaces by self-assembly. The redox response of the modified electrodes was compared with the obtained for a similar iron porphyrin in solution, confirming the immobilisation of the metalloporphyrin. The gravimetric data obtained by electrochemical quartz crystal microbalance (EQCM) during adsorption allowed an estimation of the electrode coverage, providing further evidence for the formation of the porphyrin SAM. The modified electrodes were also measured by conventional and imaging ellipsometry. The electrocatalytic activity of the two modified electrodes was tested for the reduction of the molecular oxygen. (C) 2002 Elsevier Science B.V. All rights reserved.

The present work refers to an X-ray microtomography experiment aiming at the elucidation of some aspects regarding particle distribution in SiC-particle-reinforced functionally graded aluminium composites.
Precursor composites were produced by rheocasting. These were then molten and centrifugally cast to obtain the
functionally graded composites. From these, cylindrical samples, around 1 mm in diameter, were extracted, which were then irradiated with a X-ray beam produced at the European Synchrotron Radiation Facility.
The 3-D images were obtained in edge-detection mode. A segmentation procedure has been adapted in order to
separate the pores and SiC particles from the Al matrix. Preliminary results on the particle and pore distributions are presented.

Co-combustion tests of dry sewage sludges with coal were performed in a pilot bubbling FBC aiming at the characterization of ashes and determining the behaviour of heavy metals in the process. The tests showed compliance with the regulatory levels as far as heavy metal emissions were concerned. The bottom ashes, which accounted for about 70% of the total ash production, were obtained in a granular form, with diameters ranging from 0.5 to 4 mm. The heavy metals were distributed in ashes obtained from different locations of the installation and their concentrations were found to vary depending on the location of capture. The increase in heavy metals content in bottom ashes was not found to lead to higher leachability and ecotoxicity compared to sewage sludges, suggesting that there could be opportunities for their further use. Mercury suffered vaporisation inside the reactor, thus leaving bottom ashes free of contamination by it. However, there was observed a strong retention of mercury in cyclone ashes due to the presence of unburned carbon which probably acted as an adsorbent. The effluent mercury was also found to be mostly associated with the particulate fraction, being less than 20% emitted in gaseous forms. The results suggested that the combustion of the sewage sludge could successfully be carried out and the amount of unburned carbon leaving the combustor but captured in cyclone was large enough to ensure substantial retention of mercury at low temperatures, hence could contribute to an improvement of the mercury release which still remains an issue of great concern to resolve during combustion of waste materials.

A synthesis on the state of art on dinosaur knowledge in Portugal is presented. The following genera have been recognized: Ceratosaurus, Torvosaurus, Lourinhanosaurus, Allosaurus, cf. Compsognathus, Stokesosaurus, cf. Richardoestesia, cf. Archaeopteryx, Euronychodon, cf. Paronychodon, Dinheirosaurus, Lourinhasaurus, Lusotitan, cf. Pleurocoelus, Lusitanosaurus, Dacentrurus, Dracopelta, Phyllodon, Hypsilophodon, Alocodon, Trimucrodon, Draconyx, Iguanodon, and Taveirosaurus. Most are from Late Jurassic localities at the Lourinhã area and Guimarota. A new genus, Lusotitan, is here raised to include the Late Jurassic ‘Brachiosaurus’ atalaiensis. Lower Cretaceous until Cenomanian material is scarce, except for dinosaur footprints. An interesting Late-Cretaceous, mostly small dinosaur association has been collected between Aveiro and Taveiro.

n/a

A new Lower Cretaceous (Aptian-Albian) dinosaur tracksite at the Olhos de Água beach is described. It is the first vertebrate fossil finding ever found in the concerned unit, and yielded 128 tracks in 17 trackways within an area of ca. 80 square metres.
Three tridactyl footprint morphotypes have been recognized: - Type 1 (“Iguanodontipus-like”) - trackways D, F, K, J and P; - Type 2 (large theropod), although larger in size, typically from a Grallator-like theropod footprint, i.e. A, B, G, H and O trackways; - Type 3 (medium size theropod); M is the only track of this type. There are other, poorly preserved, unidentified trackways. The theropod, swinging trackway B was produced by an animal that was limping. The theropod track M starts eastwards but drastically changes westwards, speeding up at the same time; this dinosaur decided to turn around and run in the opposite direction.
This site shows three main trackway directions: to the South, to the East, and westwards. Except for the trackway O, large theropods A, B, G and H walked southwards. Perpendicularly to these, ornithopods, small theropods and unidentified trackmakers walked towards East (5) and West (7). The segregation of trackmakers and directions, with large theropod trackways southwards and other dinosaurs’ west or eastwards, may mean that large theropods patrolled a walkway area to an important resource, most probably water, often frequented by ornithopods and smaller theropods. There is no evidence of social behavior or gregarism: footprints’ overposition shows that the large, southwards walking theropods passed on different occasions. Three trackway sequences can be established by chronologic order.