A large collection of vertebrate coprolites from black lacustrine shales in the Late Triassic (Rhaetian–Sinemurian) Kap Stewart Formation, East Greenland is examined with regard to internal and external morphology, prey inclusions, and possible relationships to the contemporary vertebrate fauna. A number of the coprolites were mineralogically examined by X-ray diffraction (XRD), showing the primary mineral composition to be apatite, clay minerals, carbonates and, occasionally, quartz in the form of secondary mineral grains. The coprolite assemblage shows multiple sizes and morphotypes of coprolites, and different types of prey inclusions, demonstrating that the coprolite assemblage originates from a variety of different producers.Supplementary material: A description of the size, shape, structure, texture, contents and preservation of the 328 specimens is available at https://doi.org/10.6084/m9.figshare.c.2134335

An alternative technique for production of devices which uses both silicon crystalline wafers (p-type) and heavy doped amorphous silicon thin films (n-type) is reported. The amorphous silicon acts as a finite source of dopant and is deposited (at low temperature, 70 °C) by plasma enhanced chemical vapor deposition on silicon wafers. Afterwards, the process of dopant diffusion into the crystalline silicon occurs in a diffusion furnace at 1000 °C for 2 h, to create p–n junctions. Using SIMS analyses, a dopant (P) transfer into c-Si of about 30% is verified and 87% of the dopant transferred is electrically active. Consequently, n-MOSFET devices are produced using a gate oxide thermally grown at the same diffusion temperature for one hour. The preliminary results of the MOSFET (channel length and width of 0.5 and 5 mm, respectively) show a depletion behavior with a threshold voltage, Vth=−8.2 V and afield-effect mobility, µ_FE=187.8 cm²/(Vs).

In this study, amorphous indium-tungsten oxide (IWO) semiconductor thin films were prepared by an eco-friendly spin-coating process using ethanol and water as solvents. The electrical properties of IWO thin-film transistors (TFTs), together with the structural and morphological characteristics of IWO thin films, were systematically investigated as functions of tungsten concentration and annealing temperature. The optimized IWO channel layer was then integrated on an aqueous aluminum oxide (AlOx) gate dielectric. It is observed that the solution-processed IWO/AlOx TFT presents high stability and improved characteristics, such as an on/off current ratio of 5 × 107, a field-effect mobility of 15.3 cm2 V-1 s-1, a small subthreshold slope of 68 mV dec-1, and a threshold voltage shift of 0.15 V under bias stress for 2 h. The IWO/AlOx TFT could be operated at a low voltage of 2 V, which was 15 times lower than that of conventional SiO2-based devices. The solution-processed IWO thin films synthesized in a green route would be promising candidates for large-area and high-performance low-cost devices. © The Royal Society of Chemistry 2016.

n/a

n/a

Although there are a few research studies on solution-processed p-channel oxide thin-film transistors (TFTs), the strict fabrication conditions and the poor electrical properties have limited their applications in low-power complementary metal oxide semiconductor (CMOS) electronics. Here, the application of the polyol reduction method for processing p-type CuxO and NiOx channel layers and their implementation in TFT devices are reported. The optimized CuxO and NiOx TFTs were achieved at low annealing temperatures (∼300 °C) and exhibited decent electrical properties. Encouraged by the inspiring results obtained on SiO2/Si substrates, the TFT performance was further optimized by device engineering, employing high-k AlOx as the gate dielectric. The fully solution-processed NiOx/AlOx TFT could be operated at a low voltage of 3.5 V and exhibits a high hole mobility of around 25 cm2 V-1 s-1. Our work demonstrates the ability to grow high-quality p-type oxide films and devices via the polyol reduction method over large area substrates while at the same time it provides guidelines for further p-type oxide material and device improvements. © The Royal Society of Chemistry 2016.

© 2016 Taylor {&} Francis.A laboratory-based methodology was designed to assess the bioreceptivity of glazed tiles. The experimental set-up consisted of multiple steps: manufacturing of pristine and artificially aged glazed tiles, enrichment of phototrophic microorganisms, inoculation of phototrophs on glazed tiles, incubation under optimal conditions and quantification of biomass. In addition, tile intrinsic properties were assessed to determine which material properties contributed to tile bioreceptivity. Biofilm growth and biomass were appraised by digital image analysis, colorimetry and chlorophyll a analysis. SEM, micro-Raman and micro-particle induced X-ray emission analyses were carried out to investigate the biodeteriorating potential of phototrophic microorganisms on the glazed tiles. This practical and multidisciplinary approach showed that the accelerated colonization conditions allowed different types of tile bioreceptivity to be distinguished and to be related to precise characteristics of the material. Aged tiles showed higher bioreceptivity than pristine tiles due to their higher capillarity and permeability. Moreover, biophysical deterioration caused by chasmoendolithic growth was observed on colonized tile surfaces.

The aim of this work is to study the behaviour of reinforced concrete flat slab structures under combined vertical and horizontal cyclic loading. A total of five specimens were cast and tested: a control specimen was punched without eccentricity, one specimen was tested under constant vertical loading and monotonically increased eccentricity until failure and the remaining three were tested under constant vertical load, at different shear ratios, and cyclic horizontal loading with increasing horizontal drift ratios. All slabs were similar, measuring 4.25×1.85×0.15m3. The reinforced concrete slab specimens were connected to two steel half columns by 0.25×0.25m2 rigid steel plates, prestressed against the slab using steel bolts, to ensure monolithic behaviour. The cyclic tests were performed using an innovative test setup that allows bending moment redistribution, line of inflection mobility, assures equal vertical displacements at the North-South borders and symmetrical shear forces. Results show that cyclic horizontal actions are very harmful to the slab–column connection, resulting in low horizontal drifts and energy dissipation.

Flat slab structures are a very common structural solution nowadays, due to their architectural and economic advantages. However, flat slab-column connections may be vulnerable to punching failure, especially in an event of an earthquake, with potentially high human and economic losses. This type of structural solution is adequately covered by design codes and recommendations in North America, due to a large amount of experimental research carried out. In Europe the situation is different, missing specific guidance to flat slab design under earthquake action in most European codes. The ACI 318-14 prescriptive approach to the gravity shear ratio-drift ratio relationship shows good agreement with experimental results. Following a similar approach and, based in a databank containing cyclic horizontally loaded tests of slab-column connections found in literature, proposals are made applicable to EC2 and MC2010.

Model-driven engineering (MDE) is believed to have a significant impact in software quality. However, researchers and practitioners may have a hard time locating consolidated evidence on this impact, as the available information is scattered in several different publications. Our goal is to aggregate consolidated findings on quality in MDE, facilitating the work of researchers and practitioners in learning about the coverage and main findings of existing work as well as identifying relatively unexplored niches of research that need further attention. We performed a tertiary study on quality in MDE, in order to gain a better understanding of its most prominent findings and existing challenges, as reported in the literature. We identified 22 systematic literature reviews and mapping studies and the most relevant quality attributes addressed by each of those studies, in the context of MDE. Maintainability is clearly the most often studied and reported quality attribute impacted by MDE. Eighty out of 83 research questions in the selected secondary studies have a structure that is more often associated with mapping existing research than with answering more concrete research questions (e.g., comparing two alternative MDE approaches with respect to their impact on a specific quality attribute). We briefly outline the main contributions of each of the selected literature reviews. In the collected studies, we observed a broad coverage of software product quality, although frequently accompanied by notes on how much more empirical research is needed to further validate existing claims. Relatively, little attention seems to be devoted to the impact of MDE on the quality in use of products developed using MDE.