Transparent, undoped semiconductive thin films of zinc oxide were deposited by radio frequency plasma enhanced reactive thermal evaporation of zinc rods in the presence of oxygen at room temperature, without any post-deposition annealing treatments. The study of the variation of rf power, in the range 5-200W, on the main properties of these films was made. A decrease of the electrical conductivity of these films with increasing rf power was observed (10(-3) to 10(-12) (Omega cm)(-1)), respectively, while the average visible transparency was kept practically constant (approximate to 80%). From this initial study, a set of bottom-gate type thin-film transistors were made using the most promising semiconductor materials. Preliminary I(V) measurements showed all transistors working, with best results obtained from zinc oxide material deposited at the lowest rf power (20 W), within the deposition conditions range which leads to semiconductive material. Such devices presented an I-on (20 V)/I-off (-5 V) ratio of 6 x 10(6) and a field-effect mobility of 0.37 cm(2)/(V s). (C) 2010 Elsevier B.V. All rights reserved.

Transparent, undoped semiconductive thin films of zinc oxide were deposited by radio frequency plasma enhanced reactive thermal evaporation of zinc rods in the presence of oxygen at room temperature, without any post-deposition annealing treatments. The study of the variation of rf power, in the range 5-200W, on the main properties of these films was made. A decrease of the electrical conductivity of these films with increasing rf power was observed (10(-3) to 10(-12) (Omega cm)(-1)), respectively, while the average visible transparency was kept practically constant (approximate to 80%). From this initial study, a set of bottom-gate type thin-film transistors were made using the most promising semiconductor materials. Preliminary I(V) measurements showed all transistors working, with best results obtained from zinc oxide material deposited at the lowest rf power (20 W), within the deposition conditions range which leads to semiconductive material. Such devices presented an I-on (20 V)/I-off (-5 V) ratio of 6 x 10(6) and a field-effect mobility of 0.37 cm(2)/(V s). (C) 2010 Elsevier B.V. All rights reserved.

In this paper we present an amorphous silicon device that can be used in two operation modes to measure the concentration of ions in solution. While crystalline devices present a higher sensitivity, their amorphous counterpart present a much lower fabrication cost, thus enabling the production of cheap disposable sensors for use, for example, in the food industry. The devices were fabricated on glass substrates by the PECVD technique in the top gate configuration, where the metallic gate is replaced by an electrolytic solution with an immersed Ag/AgCl reference electrode. Silicon nitride is used as gate dielectric enhancing the sensitivity and passivation layer used to avoid leakage and electrochemical reactions. In this article we report on the semiconductor unit, showing that the device can be operated in a light-assisted mode, where changes in the pH produce changes on the measured ac photocurrent. In alternative the device can be operated as a conventional ion selective field effect device where changes in the pH induce changes in the transistor's threshold voltage.

In this paper we present an amorphous silicon device that can be used in two operation modes to measure the concentration of ions in solution. While crystalline devices present a higher sensitivity, their amorphous counterpart present a much lower fabrication cost, thus enabling the production of cheap disposable sensors for use, for example, in the food industry. The devices were fabricated on glass substrates by the PECVD technique in the top gate configuration, where the metallic gate is replaced by an electrolytic solution with an immersed Ag/AgCl reference electrode. Silicon nitride is used as gate dielectric enhancing the sensitivity and passivation layer used to avoid leakage and electrochemical reactions. In this article we report on the semiconductor unit, showing that the device can be operated in a light-assisted mode, where changes in the pH produce changes on the measured ac photocurrent. In alternative the device can be operated as a conventional ion selective field effect device where changes in the pH induce changes in the transistor's threshold voltage.

Nowadays, among the available transparent semiconductors for device use, the great majority (if not all) have n-type conductivity. The fabrication of a transparent p-type semiconductor with good optoelectronic properties (comparable to those of n-type: InOx, ITO, ZnOx or FTO) would significantly broaden the application field of thin films. However, until now no material has yet presented all the required properties. Cu2S is a p-type narrow-band-gap material with an average optical transmittance of about 60% in the visible range for 50 nm thick films. However, due to its high conductivity at room temperature, 10 nm in thickness seems to be appropriate for device use. Cu2S thin films with 10 nm in thickness have an optical visible transmittance of about 85% rendering them as very good candidates for transparent p-type semiconductors. In this work CuxS thin films were deposited on alkali-free (AF) glass by thermal evaporation. The objective was not only the determination of its optoelectronic properties but also the feasibility of an active layer in a p-type thin film transistor. In our CuxS thin films, p-type high conductivity with a total visible transmittance of about 50% have been achieved. (C) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Nowadays, among the available transparent semiconductors for device use, the great majority (if not all) have n-type conductivity. The fabrication of a transparent p-type semiconductor with good optoelectronic properties (comparable to those of n-type: InOx, ITO, ZnOx or FTO) would significantly broaden the application field of thin films. However, until now no material has yet presented all the required properties. Cu2S is a p-type narrow-band-gap material with an average optical transmittance of about 60% in the visible range for 50 nm thick films. However, due to its high conductivity at room temperature, 10 nm in thickness seems to be appropriate for device use. Cu2S thin films with 10 nm in thickness have an optical visible transmittance of about 85% rendering them as very good candidates for transparent p-type semiconductors. In this work CuxS thin films were deposited on alkali-free (AF) glass by thermal evaporation. The objective was not only the determination of its optoelectronic properties but also the feasibility of an active layer in a p-type thin film transistor. In our CuxS thin films, p-type high conductivity with a total visible transmittance of about 50% have been achieved. (C) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

n/a

n/a

High temperature superconducting (HTS) machines are recognized to offer several advantageous features when comparing to conventional ones. Amongst these, highlights the decrease in weight and volume of the machines, due to increased current density in conductors or the absence of iron slots' teeth; or the decrease in AC losses and consequent higher efficiency of the machines, even accounting for cryogenics. These concepts have been already demonstrated and some machines have even achieved commercial stage. In this paper, several alternative approaches are applied to electrical motors employing HTS materials. The first one is an all superconducting linear motor, where copper conductors and permanent magnets are replaced by Bi-2223 windings and trapped flux magnets, taking advantage of stable levitation due to flux pinning, higher current densities and higher excitation field. The second is an induction disk motor with Bi-2223 armature, where iron, ironless and hybrid approaches are compared. Finally, an innovative command strategy, consisting of an electronically variable pole pairs' number approach, is applied to a superconducting hysteresis disk motor. All these concepts are being investigated and simulation and experimental results are presented.

A fluorene-based pi-conjugated copolymer with on-chain dibenzoborole units was used in the development of a nanocoated gold interdigitated microelectrode array device which successfully detects fluoride in a broad range of concentrations (10(-11)-10(-4) M) in aqueous solution, upon impedance spectroscopy measurements. A calibration curve obtained over this range of concentrations and a new analytical method based on impedance spectroscopy measurements in aqueous solution is proposed. The sensor nanofilm was produced by spin-coating and diagnosed via spectroscopic ellipsometry, AFM, and electrically conductivity techniques. Changes in the conductivity due to the boron-fluoride complex formation seem to be the major mechanism behind the dependence of impedimetric results on the fluoride concentration. (C) 2010 Elsevier B.V. All rights reserved.

A fluorene-based pi-conjugated copolymer with on-chain dibenzoborole units was used in the development of a nanocoated gold interdigitated microelectrode array device which successfully detects fluoride in a broad range of concentrations (10(-11)-10(-4) M) in aqueous solution, upon impedance spectroscopy measurements. A calibration curve obtained over this range of concentrations and a new analytical method based on impedance spectroscopy measurements in aqueous solution is proposed. The sensor nanofilm was produced by spin-coating and diagnosed via spectroscopic ellipsometry, AFM, and electrically conductivity techniques. Changes in the conductivity due to the boron-fluoride complex formation seem to be the major mechanism behind the dependence of impedimetric results on the fluoride concentration. (C) 2010 Elsevier B.V. All rights reserved.

In view of the increasing need for larger-area display devices with improved image quality it becomes increasingly important to decrease resistivity while maintaining transparency in transparent conducting oxides (TCOs). Accomplishing the goal of increased conductivity and transparency will require a deeper understanding of the relationships between the structure and the electro-optical properties of these materials. In this work we study the role of tin doping in InOx thin films. Undoped indium oxide (InOx) and indium tin oxide (ITO) thin films were deposited at room temperature by radio-frequency plasma enhanced reactive thermal evaporation (rf-PERTE), a new technique recently developed in our laboratory using as evaporation source either In rods or a 90%In:10%Sn alloy, respectively. The two most important macroscopic properties-optical transparency and electrical resistivity-seem to be independent of the tin content in these deposition conditions. Results show that the films present a visible transmittance of the order of 82%, and an electrical resistivity of about 8 x 10(-4) Omega . cm. Surface morphology characterization made by atomic force microscopy (AFM) showed that homogeneity of the films deposited from a 90%In:10%Sn alloy is enhanced (a film with small and compact grains is produced) and consequently a smooth surface with reduced roughness and with similar grain size and shape is obtained. Films deposited from pure In rods evaporation source show the presence of aggregates randomly distributed above a film tissue formed of thinner grains.

In view of the increasing need for larger-area display devices with improved image quality it becomes increasingly important to decrease resistivity while maintaining transparency in transparent conducting oxides (TCOs). Accomplishing the goal of increased conductivity and transparency will require a deeper understanding of the relationships between the structure and the electro-optical properties of these materials. In this work we study the role of tin doping in InOx thin films. Undoped indium oxide (InOx) and indium tin oxide (ITO) thin films were deposited at room temperature by radio-frequency plasma enhanced reactive thermal evaporation (rf-PERTE), a new technique recently developed in our laboratory using as evaporation source either In rods or a 90%In:10%Sn alloy, respectively. The two most important macroscopic properties-optical transparency and electrical resistivity-seem to be independent of the tin content in these deposition conditions. Results show that the films present a visible transmittance of the order of 82%, and an electrical resistivity of about 8 x 10(-4) Omega . cm. Surface morphology characterization made by atomic force microscopy (AFM) showed that homogeneity of the films deposited from a 90%In:10%Sn alloy is enhanced (a film with small and compact grains is produced) and consequently a smooth surface with reduced roughness and with similar grain size and shape is obtained. Films deposited from pure In rods evaporation source show the presence of aggregates randomly distributed above a film tissue formed of thinner grains.

Conductive and transparent undoped thin films of indium oxide (InOx), 120 nm average thick, were deposited by radio frequency plasma enhanced reactive thermal evaporation (rf-PERTE) of indium in the presence of oxygen at room temperature. Several substrates were used in order to study their influence on the main properties of these films: alkali free (AF) glass, fused silica, crystalline silicon and polyethylene terephthalate (PET). Surface morphology of the InOx films as a function of the substrates was observed by SEM and showed that the undoped InOx films obtained are nano-structured. For the c-Si substrate, InOx films with increased grain size are obtained, induced by the crystalline substrate. Films deposited on fused silica and AF glass substrates show a nano-grainy surface with similar surface morphologies. The InOx films deposited on AF glass show the highest values of both: electrical conductivity of about 1100 (Omega cm)(-1) and visible transmittance of 85%. The substrate has a greater influence on the surface morphology of the films when a polymer (PET) is used. InOx films deposited on PET show a decrease in the electrical conductivity (90 (Omega cm)(-1)) and a slight decrease in the average visible transmittance (78%).

Conductive and transparent undoped thin films of indium oxide (InOx), 120 nm average thick, were deposited by radio frequency plasma enhanced reactive thermal evaporation (rf-PERTE) of indium in the presence of oxygen at room temperature. Several substrates were used in order to study their influence on the main properties of these films: alkali free (AF) glass, fused silica, crystalline silicon and polyethylene terephthalate (PET). Surface morphology of the InOx films as a function of the substrates was observed by SEM and showed that the undoped InOx films obtained are nano-structured. For the c-Si substrate, InOx films with increased grain size are obtained, induced by the crystalline substrate. Films deposited on fused silica and AF glass substrates show a nano-grainy surface with similar surface morphologies. The InOx films deposited on AF glass show the highest values of both: electrical conductivity of about 1100 (Omega cm)(-1) and visible transmittance of 85%. The substrate has a greater influence on the surface morphology of the films when a polymer (PET) is used. InOx films deposited on PET show a decrease in the electrical conductivity (90 (Omega cm)(-1)) and a slight decrease in the average visible transmittance (78%).