n/a

An equivalent model and electromechanical characteristics for the disk motor was obtained based on the Steinmetz parameters. This paper describes a series of tests conducted on an axial flux motor, equipped with an aluminum rotor disc and an YBCO high temperature superconducting rotor disc, at liquid nitrogen temperature (77 K). The rotating magnetic field was produced by a four-pole, three-phase stator winding, at 50 Hz. At asynchronous permanent regime, Steinmetz-type models are able to describe both motors' behavior. From the performed tests, the parameters of both motors' models were deduced. A variable load was used to obtain both motor's characteristics (conventional and superconducting). Experimental obtained characteristics of both motors are compared with the ones predicted from parameters' calculation. The HTS motor provides high efficiency then the conventional ones.

n/a

n/a

n/a

n/a

n/a

n/a

n/a

n/a

n/a

n/a

n/a

In software, hardware, and embedded system domains, debugging is the process of locating and correcting faults in a system. Depending on the context, the various characteristics of debugging induce different challenges and solutions. Post-silicon hardware debugging, for example, needs to address issues such as limited visibility and controllability, while debugging software entails other issues, such as the handling of distributed or non-deterministic computation. The challenges that accompany such issues are the focus of many current research efforts. Solutions for debugging range from interactive tools to highly analytic techniques. We have seen great advances in debugging technologies in recent years, but bugs continue to occur, and debugging still encompasses significant portions of the life-cycles of many systems. The session covered state-of-the-art approaches as well as promising new research directions in both the hardware and software domains.

This paper presents a step-up micro-power converter for solar energy harvesting applications. The circuit uses a SC voltage tripler architecture, controlled by an MPPT circuit based on the Hill Climbing algorithm. This circuit was designed in a 0.13 mu m CMOS technology in order to work with an a-Si PV cell. The circuit has a local power supply voltage, created using a scaled down SC voltage tripler, controlled by the same MPPT circuit, to make the circuit robust to load and illumination variations. The SC circuits use a combination of PMOS and NMOS transistors to reduce the occupied area. A charge re-use scheme is used to compensate the large parasitic capacitors associated to the MOS transistors. The simulation results show that the circuit can deliver a power of 1266 mu W to the load using 1712 mu W of power from the PV cell, corresponding to an efficiency as high as 73.91%. The simulations also show that the circuit is capable of starting up with only 19% of the maximum illumination level.

n/a

n/a

Transactional Memory [3] (TM) is a new paradigm for concurrency control that brings the concept of transactions, widely known from the Databases community, into the management of data located in main memory. TM delivers a powerful semantics for constraining concurrency and provides the means for the extensive use of the available parallel hardware. TM uses abstractions that promise to ease the development of scalable parallel applications by achieving performances close to fine-grained locking while maintaining the simplicity of coarse-grained locking.

n/a

During electric polarization charge is injected into the material. The structure is decorated with space charge and during the subsequent heating an apparent peak and the genuine peaks that are related to dipole randomization and charge detrapping are observed. The method is used here to analyze the molecular movements in polyimide in the temperature range from 293 to 623 K. Two weak relaxations have been observed around 337 K and around 402 K. The electrical conductivity changes with temperature in agreement with the Arrhenius law only below (W= (0.84 +/- 0.03) eV) and above ( W (0.82 +/- 0.03) eV) the temperature range where the beta relaxation is observed. The variation of the electrical conductivity with temperature, in the range of the beta relaxation, is controlled by the variation of the charge currier mobility with temperature and it shows a non-Arrhenius behavior. We suggest that the beta(1) sub-glass relaxation is related to the rotation or oscillation of phenyl groups and the beta(2) sub-glass relaxation is related to the rotation or oscillation of the imidic ring. At higher temperatures an apparent peak was observed. The relaxation time of the trapped charge, at 573 K, is high than 8895 s. (C) 2010 Elsevier B.V. All rights reserved.

n/a

n/a

n/a

The application of diffraction gratings to solar cells is a promising approach to superseding the light trapping limits of conventional Lambertian structures. In this paper a mathematical formalism is derived for calculating the absorption that can be expected in a solar cell equipped with a diffraction grating, which can be applied to any lattice geometry and grating profile. Furthermore, the formalism is used to calculate the upper limit of total absorption that can theoretically be achieved using a diffraction grating. The derived formalism and limits are valid when the solar cell thickness is greater than the coherence length of the illuminating solar spectrum. Comparison is made to the upper limit achievable using an angularly selective Rugate filter, which is also calculated. Both limits are found to be considerably higher than the Lambertian limit within the range of sunlight concentration factors practically employed in photovoltaic systems (1–1000×). The upper limit of absorption using the diffraction grating is shown to be equal to the thermodynamic limit for all absorbances and concentration factors. The limit for the Rugate filter is generally lower, but tends to the thermodynamic limit for lower cell absorbances. Copyright © 2011 John Wiley {&} Sons, Ltd.

New compounds of the general formulas [M(Ar-BIAN)(2)]BF(4) and [M(Ar-BIAN)(NCMe)(2)]BF(4), where M=Cu(1) or Ag(1) and Ar-BIAN = bis(aryl)acenaphthenequinonediimine, were synthesized by the direct reaction of [Cu(NCMe)(4)]BF(4) or [Ag(NCMe)(4)]BF(4) with the corresponding Ar-BIAN ligand in dried CH(2)Cl(2). The synthesized compounds are [M(o, d, p-Me(3)C(6)H(2)-BIAN)(2)]BF(4) where M = Cu(1) (1) and Ag(1) (2), [M(o,d-iPr(2)C(6)H(3)-BIAN)(NCMe)(2)]BF(4) where M = Cu(1) (3) and Ag(1) (4), and [Ag(o,d-iPr(2)C(6)H(3)-BIAN)(2)]BF(4) (5). The crystal structures of compounds 1-3 and 5 were solved by singlecrystal X-ray diffraction. In all cases copper(I) or silver(I) are in a distorted tetrahedron that is constructed from the four nitrogen atoms of the two a-diimine ligands or, in 3, from one a-diimine ligand and two acetonitrile molecules. All compounds were characterized by elemental analyses, matrix-assisted laser desorption ionization time-of-flight mass spectrometry, and IR, UV-vis, and (1)H NMR spectroscopy. The analysis of the molecular geometry and the energetic changes for the formation reactions of the complexes, in a CH(2)Cl(2) solution, were evaluated by density functional theory calculations and compared with the experimental results.