n/a

n/a

n/a

n/a

n/a

n/a

n/a

n/a

The thermal decompositions of methyl azidoformate (N3COOMe), ethyl azidoformate (N3COOEt) and 2-azido-N,N-dimethylacetamide (N3CH2CONMe2) have been studied by matrix isolation infrared spectroscopy and real-time ultraviolet photoelectron spectroscopy. N2 appears as an initial pyrolysis product in all systems, and the principal interest lies in the fate of the accompanying organic fragment. For methyl azidoformate, four accompanying products were observed: HNCO, H2CO, CH2NH and CO2, and these are believed to arise as a result of two competing decomposition routes of a four-membered cyclic intermediate. Ethyl azidoformate pyrolysis yields four corresponding products: HNCO, MeCHO, MeCHNH and CO2, together with the five-membered-ring compound 2-oxazolidone. In contrast, the initial pyrolysis of 2-azido-N,N-dimethyl acetamide, yields the novel imine intermediate Me2NCOCHNH, which subsequently decomposes into dimethyl formamide (HCONMe2), CO, Me2NH and HCN. This intermediate was detected by matrix isolation IR spectroscopy, and its identity confirmed both by a molecular orbital calculation of its IR spectrum, and by the temperature dependence and distribution of products in the PES and IR studies. Mechanisms are proposed for the formation and decomposition of all the products observed in these three systems, based on the experimental evidence and the results of supporting molecular orbital calculations.

The thermal decompositions of methyl azidoformate (N3COOMe), ethyl azidoformate (N3COOEt) and 2-azido-N,N-dimethylacetamide (N3CH2CONMe2) have been studied by matrix isolation infrared spectroscopy and real-time ultraviolet photoelectron spectroscopy. N2 appears as an initial pyrolysis product in all systems, and the principal interest lies in the fate of the accompanying organic fragment. For methyl azidoformate, four accompanying products were observed: HNCO, H2CO, CH2NH and CO2, and these are believed to arise as a result of two competing decomposition routes of a four-membered cyclic intermediate. Ethyl azidoformate pyrolysis yields four corresponding products: HNCO, MeCHO, MeCHNH and CO2, together with the five-membered-ring compound 2-oxazolidone. In contrast, the initial pyrolysis of 2-azido-N,N-dimethyl acetamide, yields the novel imine intermediate Me2NCOCHNH, which subsequently decomposes into dimethyl formamide (HCONMe2), CO, Me2NH and HCN. This intermediate was detected by matrix isolation IR spectroscopy, and its identity confirmed both by a molecular orbital calculation of its IR spectrum, and by the temperature dependence and distribution of products in the PES and IR studies. Mechanisms are proposed for the formation and decomposition of all the products observed in these three systems, based on the experimental evidence and the results of supporting molecular orbital calculations.

n/a

n/a

It is experimentally known that the linearity and sensitivity of the position sensitive detectors (PSD) are dependent on the resistance of the collecting layer and of the load resistance, mainly if the detection is based on the measurement of the photo-lateral voltage. To determine the value of the load resistance to be used in metal - insulator - semiconductor (MIS) PSDs structures that lead to the maximum value of sensitivity and linearity, we propose an electrical model through which it is able to simulate the proper sensor response and how the load resistance influence the results obtained. This model is valid for PSDs where the resistance of the collecting resistive layer is quite low (≤ 500 Ω), leading to a low output impedance. Under these conditions we conclude that the value of the load resistance should be of about 1 kΩ in order to achieve a good compromise between the linearity and the sensitivity of the PSD. This result is in agreement with the set of experiments performed. © 2005 Materials Research Society.

n/a

n/a

n/a

n/a

n/a

n/a

n/a

n/a

n/a

The linearity and sensitivity of linear Position Sensitive Detectors (PSD) are the two principal characteristics of sensors to be optimised in sensor fabrication. This work presents several efforts made to understand the internal and external parameters that influence the linearity and sensitivity of Metal Insulator Semiconductor (MIS) linear PSD with an active length of 6 cm. The use of long sensitive areas allows the PSD to achieve greater resolution without the need of a highly accurate light spot integration mechanism. The PSD is built in a multi-layered structure consisting of Cr/a-Si:H (n+ doped)/a-Si:H (intrinsic)/SiOx (passivation layer)/Au, where the active a-Si:H layers were deposited by Modified Triode Plasma Enhanced Chemical Vapour Deposition (MTPECVD), which allows the deposition of good electronic grade material with a low (≈ 1 × 1015 cm-3) defect density inferred by CPM. The sensor linearity and sensitivity shows dependence on the sensor width to length ratio, SiOx layer and on the value of the load resistance. Sensitivities of more than 30 mV/cm were achieved with linearity near 99%. Besides that, this type of MIS structure allows an improved spectral response in the near-UV region and has its maximum response at 540 nm. © 2005 Springer Science + Business Media, Inc.

n/a

n/a