Ana Rita C. Duarte

THEDES, so called therapeutic deep eutectic solvents are here defined as a mixture of two components, which at a particular molar composition become liquid at room temperature and in which one of them is an active pharmaceutical ingredient (API). In this work, THEDES based on menthol complexed with three different APIs, ibuprofen (ibu), BA (BA) and phenylacetic acid (PA), were prepared. The interactions between the components that constitute the THEDES were studied by NMR, confirming that the eutectic system is formed by H-bonds between menthol and the API. The mobility of the THEDES components was studied by PFGSE NMR spectroscopy. It was determined that the self-diffusion of the species followed the same behavior as observed previously for ionic liquids, in which the components migrate via jumping between voids in the suprastructure created by punctual thermal fluctuations. The solubility and permeability of the systems in an isotonic solution was evaluated and a comparison with the pure APIs was established through diffusion and permeability studies carried out in a Franz cell. The solubility of the APIs when in the THEDES system can be improved up to 12 fold, namely for the system containing ibu. Furthermore, for this system the permeability was calculated to be 14 × 10−5 cm/s representing a 3 fold increase in comparison with the pure API. With the exception of the systems containing PA an increase in the solubility, coupled with an increase in permeability was observed. In this work, we hence demonstrate the efficiency of THEDES as a new formulation for the enhancement of the bioavailability of APIs by changing the physical state of the molecules from a solid dosage to a liquid system.

In this work, stents were produced from natural origin polysaccharides. Alginate, gellan gum, and a blend of these with gelatin were used to produce hollow tube (stents) following a combination of templated gelation and critical point carbon dioxide drying. Morphological analysis of the surface of the stents was carried out by scanning electron microscopy. Indwelling time, encrustation, and stability of the stents in artificial urine solution was carried out up to 60 days of immersion. In vitro studies carried out with simulated urine demonstrated that the tubes present a high fluid uptake ability, about 1000{%}. Despite this, the materials are able to maintain their shape and do not present an extensive swelling behavior. The bioresorption profile was observed to be highly dependent on the composition of the stent and it can be tuned. Complete dissolution of the materials may occur between 14 and 60 days. Additionally, no encrustation was observed within the tested timeframe. The ability to resist bacterial adherence was evaluated with Gram-positive Staphylococcus aureus and two Gram-negatives Escherichia coli DH5 alpha and Klebsiella oxytoca. For K. oxytoca, no differences were observed in comparison with a commercial stent (Biosoft((R)) duo, Porges), although, for S. aureus all tested compositions had a higher inhibition of bacterial adhesion compared to the commercial stents. In case of E. coli, the addition of gelatin to the formulations reduced the bacterial adhesion in a highly significant manner compared to the commercial stents. The stents produced by the developed technology fulfill the requirements for ureteral stents and will contribute in the development of biocompatible and bioresorbable urinary stents.

Abstract The present study relates to the use of supercritical carbon dioxide (SCCO{\textless}inf{\textgreater}2{\textless}/inf{\textgreater}) to modify the properties of cork by incorporation of new molecules. The impact of SCCO{\textless}inf{\textgreater}2{\textless}/inf{\textgreater}processing on the morphology and on the mechanical properties was found to be negligible.The impregnation of disperse blue 14 (blue dye) on cubic shaped cork samples of 5 mm occurs progressively,is dependent of the processing conditions and of the presence of lenticels and growth rings. The impregnation of the samples bulk was achieved with processing at 10 MPa and 313 K for 16 h. The solubility and sorption of SCCO{\textless}inf{\textgreater}2{\textless}/inf{\textgreater} in the cork matrix was measured using circular discs and the diffusion coefficients calculated to be on the order of 10{\textless}sup{\textgreater}-8{\textless}/sup{\textgreater} cm{\textless}sup{\textgreater}2{\textless}/sup{\textgreater}/s, the same order as for wood materials. This work demonstrates the feasibility of supercritical fluid technology to impart new features to cork, which may lead to innovative architectural, outdoor and industrial applications.

© 2015 Elsevier B.V. Abstract Deep eutectic solvents (DES) can be formed by bioactive compounds or pharmaceutical ingredients. A therapeutic DES (THEDES) based on ibuprofen, a non-steroidal anti-inflammatory drug (NSAID), and menthol was synthesized and its thermal behavior was analyzed by differential scanning calorimetry (DSC). A controlled drug delivery system was developed by impregnating a starch:poly-Ï$μ$-caprolactone polymeric blend (SPCL 30:70) with the menthol:ibuprofen THEDES in different ratios (10 and 20 wt{%}), after supercritical fluid sintering at 20 MPa and 50 °C. The morphological characterization of SPCL matrices impregnated with THEDES was performed by scanning electron microscopy (SEM) and micro-computed tomography (micro-CT). Drug release studies were carried out in a phosphate buffered saline. The results obtained provide important clues for the development of carriers for the sustainable delivery of bioactive compounds.

A therapeutic deep eutectic system (THEDES) is here defined as a deep eutectic solvent (DES) having an active pharmaceutical ingredient (API) as one of the components. In this work, THEDESs are proposed as enhanced transporters and delivery vehicles for bioactive molecules. THEDESs based on choline chloride (ChCl) or menthol conjugated with three different APIs, namely acetylsalicylic acid (AA), benzoic acid (BA) and phenylacetic acid (PA), were synthesized and characterized for thermal behaviour, structural features, dissolution rate and antibacterial activity. Differential scanning calorimetry and polarized optical microscopy showed that ChCl:PA (1:1), ChCl:AA (1:1), menthol:AA (3:1), menthol:BA (3:1), menthol:PA (2:1) and menthol:PA (3:1) were liquid at room temperature. Dissolution studies in PBS led to increased dissolution rates for the APIs when in the form of THEDES, compared to the API alone. The increase in dissolution rate was particularly noticeable for menthol-based THEDES. Antibacterial activity was assessed using both Gram-positive and Gram-negative model organisms. The results show that all the THEDESs retain the antibacterial activity of the API. Overall, our results highlight the great potential of THEDES as dissolution enhancers in the development of novel and more effective drug delivery systems.

Human articular cartilage functions under a wide range of mechanical loads in synovial joints, where hydrostatic pressure (HP) is the prevalent actuating force. We hypothesized that the formation of engineered cartilage can be augmented by applying such physiologic stimuli to chondrogenic cells or stem cells, cultured in hydrogels, using custom-designed HP bioreactors. To test this hypothesis, we investigated the effects of distinct HP regimens on cartilage formation in vitro by either human nasal chondrocytes (HNCs) or human adipose stem cells (hASCs) encapsulated in gellan gum (GG) hydrogels. To this end, we varied the frequency of low HP, by applying pulsatile hydrostatic pressure or a steady hydrostatic pressure load to HNC-GG constructs over a period of 3 weeks, and evaluated their effects on cartilage tissue-engineering outcomes. HNCs (10×10 6 cells/mL) were encapsulated in GG hydrogels (1.5{%}) and cultured in a chondrogenic medium under three regimens for 3 weeks: (1) 0.4 MPa Pulsatile HP; (2) 0.4 MPa Steady HP; and (3) Static. Subsequently, we applied the pulsatile regimen to hASC-GG constructs and varied the amplitude of loading, by generating both low (0.4 MPa) and physiologic (5 MPa) HP levels. hASCs (10×10 6 cells/mL) were encapsulated in GG hydrogels (1.5{%}) and cultured in a chondrogenic medium under three regimens for 4 weeks: (1) 0.4 MPa Pulsatile HP; (2) 5 MPa Pulsatile HP; and (3) Static. In the HNC study, the best tissue development was achieved by the pulsatile HP regimen, whereas in the hASC study, greater chondrogenic differentiation and matrix deposition were obtained for physiologic loading, as evidenced by gene expression of aggrecan, collagen type II, and sox-9; metachromatic staining of cartilage extracellular matrix; and immunolocalization of collagens. We thus propose that both HNCs and hASCs detect and respond to physical forces, thus resembling joint loading, by enhancing cartilage tissue development in a frequency- and amplitude-dependant manner. © Copyright 2012, Mary Ann Liebert, Inc.

© 2014 American Institute of Chemical Engineers. Significance: Natural deep eutectic solvents (NADES) are defined as a mixture of two or more solid or liquid components, which at a particular composition present a high melting point depression becoming liquids at room temperature. NADES are constituted by natural molecules and fully represent the green chemistry principles. For these reasons, the authors believe that the submitted manuscript is a highly valuable contribution to the field of green chemistry and chemical engineering. For the first time, the possibility to use NADES as enhancers of supercritical fluid technology is revealed.

A new generation of scaffolds capable of acting not only as support for cells but also as a source of biological cues to promote tissue regeneration is currently a hot topic of in bone Tissue Engineering (TE) research. The inclusion of growth factor (GF) controlled release functionalities in the scaffolds is a possible strategy to achieve such goal. Platelet Lysate (PL) is an autologous source of GFs, providing several bioactive agents known to act on bone regeneration. In this study, chitosan-chondroitin sulfate nanoparticles loaded with PL were included in a poly(d,l-lactic acid) foam produced by supercritical fluid foaming. The tridimensional (3D) structures were then seeded with human adipose-derived stem cells (hASCs) and cultured in vitro under osteogenic stimulus. The osteogenic differentiation of the seeded hASCs was observed earlier for the PL-loaded constructs, as shown by the earlier alkaline phosphatase peak and calcium detection and stronger Runx2 expression at day 7 of culture, in comparison with the control scaffolds. Osteocalcin gene expression was upregulated in presence of PL during all culture period, which indicates an enhanced osteogenic induction. These results suggest the synergistic effect of PL and hASCs in combinatory TE strategies and support the potential of PL to increase the multifunctionality of the 3D hybrid construct for bone TE applications. © 2012 Elsevier B.V. All rights reserved.

Supercritical carbon dioxide has been used as a green solvent due to their well-known potential in biomaterials impregnation. The versatility of this technique enables the loading of implants with Active Pharmaceutical Ingredients which present several benefits when compared with traditional techniques to impregnate active compounds. In this review, we have summarized the recent progresses achieved in supercritical CO2assisted impregnation of active compounds and therapeutic deep eutectic systems for biomedical applications.

© 2017 American Chemical Society. Recent findings have reported the reason why some living beings are able to withstand the huge thermal amplitudes between winter and summer in their natural habitats. They are able to produce metabolites decreasing deeply the crystallization temperature of water, avoiding cell disrupture due to the presence of ice crystals and overcoming osmotic effects. In vitro, the possibility to cool living cells and tissues to cryogenic temperatures in the absence of ice can be achieved through a vitrification process. Vitrification has been suggested as an alternative approach to cryopreservation and could hereafter follow an interesting biomimetic perspective. The metabolites produced by these animals are mostly sugars, organic acids, choline derivatives, or urea. When combined at a particular composition, these compounds form a new liquid phase which has been defined as Natural Deep Eutectic Solvents (NADES). In this review, we relate the findings of different areas of knowledge from evolutive biology, cryobiology, and thermodynamics and give a perspective to the potential of NADES in the development of new cryoprotective agents.

A laboratory-scale reactor system is built and operated to measure the kinetic of formation for single and mixed carbon dioxide-tetrahydrofuran hydrates. The T-cycle method, which is used to collect the kinetic data, is briefly discussed. For single carbon dioxide hydrate, the induction time decreases with the increase of the initial carbon dioxide pressure up to 2.96. MPa. Beyond this pressure, the induction time is becoming relatively constant with the increase of initial carbon dioxide pressure indicating that the liquid phase is completely supersaturated with carbon dioxide. Experimental results show that the inclusion of tetrahydrofuran reduces the induction time required for hydrate formation. These observations indicate hydrate nucleation process and onset growth are more readily to occur in the presence of tetrahydrofuran. In contrast, the presence of sodium chloride prolongs the induction time due to clustering of water molecules with the ions and the salting-out effects. It is also shown that the degree of subcooling required for hydrate formation is affected by the presence of tetrahydrofuran and sodium chloride in the hydrate forming system. The presence of tetrahydrofuran in the hydrate system significantly reduces the amount of carbon dioxide uptake. The apparent rate constant, k, for those systems are reported. © 2010.

The fluid phase behaviour for the binary systems carbon dioxide+cyclobutanone and propane+cyclobutanone has been determined experimentally, using Cailletet equipment. For both the systems bubble points have been determined for a number of isopleths covering the whole mole fraction range. Additionally, for the binary system carbon dioxide+cyclobutanone dew points and critical points could be observed for a number of overall-compositions rich in carbon dioxide. The temperature and pressure range were, respectively, from 278 to 369K and from 0.1 to 14.0MPa. Correlation of the experimental data of both systems has been performed using the Soave-Redlich-Kwong (SRK) equation of state. Satisfactory results have been achieved using only one binary interaction parameter. © 2003 Elsevier B.V. All rights reserved.

The design and production of structures with nanometer-sized polymer films based on layer-by-layer (LbL) are of particular interest for tissue engineering since they allow the precise control of physical and biochemical cues of implantable devices. In this work, a method is developed for the preparation of nanostructured hollow multilayers tubes combining LbL and template leaching. The aim is to produce hollow tubes based on polyelectrolyte multilayer films with tuned physical-chemical properties and study their effects on cell behavior. The final tubular structures are characterized by differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), microscopy, swelling, and mechanical tests, including dynamic mechanical analysis (DMA) in physiological simulated conditions. It is found that more robust films could be produced upon chemical cross-linking with genipin. In particular, the mechanical properties confirms the viscoelastic properties and a storage and young modulus about two times higher. The water uptake decreases from about 390{%} to 110{%} after the cross-linking. The biological performance is assessed in terms of cell adhesion, viability, and proliferation. The results obtained with the cross-linked tubes demonstrate that these are more suitable structures for cell adhesion and spreading. The results suggest the potential of these structures to boost the development of innovative tubular structures for tissue engineering approaches.

Green technology actively seeks new solvents to replace common organic solvents that present inherent toxicity and have high volatility, leading to evaporation of volatile organic compounds to the atmosphere. Over the past two decades, ionic liquids (ILs) have gained enormous attention from the scientific community, and the number of reported articles in the literature has grown exponentially. Nevertheless, IL "greenness" is often challenged, mainly due to their poor biodegradability, biocompatibility, and sustainability. An alternative to ILs are deep eutectic solvents (DES). Deep eutectic solvents are defined as a mixture of two or more components, which may be solid or liquid and that at a particular composition present a high melting point depression becoming liquids at room temperature. When the compounds that constitute the DES are primary metabolites, namely, aminoacids, organic acids, sugars, or choline derivatives, the DES are so called natural deep eutectic solvents (NADES). NADES fully represent green chemistry principles. Can natural deep eutectic solvents be foreseen as the next generation solvents and can a similar path to ionic liquids be outlined? The current state of the art concerning the advances made on these solvents in the past few years is reviewed in this paper, which is more than an overview on the different applications for which they have been suggested, particularly, biocatalysis, electrochemistry, and extraction of new data. Citotoxicity of different NADES was evaluated and compared to conventional imidazolium-based ionic liquids, and hints at the extraction of phenolic compounds from green coffee beans and on the foaming effect of NADES are revealed. Future perspectives on the major directions toward which the research on NADES is envisaged are here discussed, and these comprised undoubtedly a wide range of chemically related subjects. © 2014 American Chemical Society.

© 2017 Elsevier B.V. The preparation of natural deep eutectic solvents (NADESs) from cheap and readily available raw materials is reported. In this work, we have considered mixtures of choline chloride (CC) or betaine (Bet) with 3 sugar molecules (glucose (Glu), xylose (Xyl) and sucrose (Suc)) and 2 carboxylic acids (citric (CA) and tartaric (Tart) acids). The formation of NADESs was investigated by polarized optical microscopy (POM) and differential scanning calorimetry (DSC). The CC mixtures give origin to NADESs for 1:1 M ratio with the sugar molecules and for 2:1, 1:1 and 1:2 with the carboxylic acids, while Bet mixtures only formed NADES with the carboxylic acids. The effect of water content (up to 5{%} (wt.{%})) and temperature in conductivity and rheology were characterized. The NADESs were found to be non-thixotropic, Newtonian liquids with high viscosity, decreasing with increasing temperature and water content. The conductivity is limited by charge carrier mobility, thus increasing with water content and temperature.

Phase equilibrium measurements of single and mixed organic clathrate hydrates with hydrogen were determined within a pressure range of 2.0-14.0. MPa. The organic compounds studied were furan, 2,5-dihydrofuran, tetrahydropyran, 1,3-dioxolane and cyclopentane. These organic compounds are known to form structure II clathrate hydrates with water. It was found that the addition of hydrogen to form a mixed clathrate hydrate increases the stability compared to the single organic clathrate hydrates. Moreover, the mixed clathrate hydrate also has a much higher stability compared to a pure hydrogen structure II clathrate hydrate. Therefore, the organic compounds act as promoter materials. The stabilities of the single and mixed organic clathrate hydrates with hydrogen showed the following trend in increasing order: 1,3-dioxolane {\textless} 2,5-dihydrofuran {\textless} tetrahydropyran {\textless} furan {\textless} cyclopentane, indicating that both size and geometry of the organic compound determine the stability of the clathrate hydrates. © 2011 Elsevier B.V.

The possibility to fabricate marine collagen porous structures crosslinked with genipin under high pressure carbon dioxide is investigated. Collagen from shark skin is used to prepare pre-scaffolds by freeze-drying. The poor stability of the structures and low mechanical properties require crosslinking of the structures. Under dense CO 2 atmosphere, crosslinking of collagen pre-scaffolds is allowed for 16 h. Additionally, the hydrogels are foamed and the scaffolds obtained present a highly porous structure. In vitro cell culture tests performed with a chondrocyte-like cell line show good cell adherence and proliferation, which is a strong indication of the potential of these scaffolds to be used in tissue cartilage tissue engineering. The development of an optimized processing technique for the preparation of stable structures from marine origin collagen is described. The samples are processed under a dense carbon dioxide atmosphere that promotes crosslinking and enhances the morphology of the 3D architectures obtained. © 2013 WILEY-VCH Verlag GmbH {&} Co. KGaA, Weinheim.

Fast-dissolving delivery systems (FDDS) have received increasing attention in the last years. Oral drug delivery is still the preferred route for the administration of pharmaceutical ingredients. Nevertheless, some patients, e.g. children or elderly people, have difficulties in swallowing solid tablets. In this work, gelatin membranes were produced by electrospinning, containing an encapsulated therapeutic deep-eutectic solvent (THEDES) composed by choline chloride/mandelic acid, in a 1:2 molar ratio. A gelatin solution (30{%} w/v) with 2{%} (v/v) of THEDES was used to produce electrospun fibers and the experimental parameters were optimized. Due to the high surface area of polymer fibers, this type of construct has wide applicability. With no cytotoxicity effect, and showing a fast-dissolving release profile in PBS, the gelatin fibers with encapsulated THEDES seem to have promising applications in the development of new drug delivery systems.

In this work, blends of starch and poly-$ε$-caprolactone (PCL) doped with different concentrations of 1-butyl-3-methylimidazolium acetate ([BMIM]Ac) or 1-butyl-3-methylimidazolium chloride ([BMIM] Cl) were studied. The blends were characterized by mechanical analysis, infra-red spectroscopy (FTIR), differential scanning calorimetry (DSC) and dielectric relaxation spectroscopy (DRS), evaluating the IL doping effect. The samples were subjected to supercritical carbon dioxide foaming and the morphology of the structures was assessed. DSC shows a single glass transition and melting endotherm for foamed and unfoamed samples, having no effect upon IL doping, and DRS shows increased molecular mobility for blends with higher IL concentrations, and some hindrance for lower ones. The conductivity for SPCL doped with 30{%} [BMIM] Cl, before and after foaming, is comparable to the conductivity of the IL but exhibits more stable conductivity values, opening doors for applications as self-supported conductive materials. © 2014 the Partner Organisations.

Some approaches have been developed in our group to investigate the role of novel ionic liquids as process and property modifiers of natural-based polymers. In our previous work, we proposed the use of ionic liquids as plasticizing agents for the creation of porous structures from a semi-crystalline natural-based polymer. The current work intended to complement the previous studies, evaluating the ability of ionic liquid (IL) to plasticize polymers such as blends of starch-poly-lactic acid (SPLA) and its effect on supercritical fluid foaming process (SCF) and providing more insights on the mechanisms involved. For this purpose, blends of starch with poly (lactic) acid, with different ratios of starch and poly-lactic acid of 50:50 and 30:70 were modified and processed using 1-butyl-3-methylimidazolium chloride ([bmim]Cl). Supercritical fluid foaming was studied at different soaking times (1, 3 and 6h) using carbon dioxide at 20.0MPa and 40°C. The blends were characterized by different techniques, such as infra-red spectroscopy, differential scanning calorimetry and compression and tensile mechanical analysis. The morphology of the foamed structures was analyzed by scanning electron microscopy and micro-computed tomography. The results suggest that after 3h of soaking time an equilibrium state of carbon dioxide into the bulk samples is attained, yielding structures with 6{%} and 15{%} of porosity, for SPLA70 and SPLA50 respectively. The solubility of carbon dioxide within the matrices was studied for the same conditions and the results demonstrate a higher sorption degree in the samples doped with ionic liquid. Sorption and desorption diffusion coefficients of supercritical CO 2 in the SPLA matrix were determined for the raw polymer and for the SPLA doped with [bmim]Cl. It was found that the lower desorption diffusion coefficients are related with the higher porosity obtained by the foaming process. © 2013.

© 2014 American Chemical Society. Engineering metabolically demanding tissues requires the supply of nutrients, oxygen, and removal of metabolic byproducts, as well as adequate mechanical properties. In this work, we propose the development of chitosan (CHIT)/alginate (ALG) freestanding membranes fabricated by layer-by-layer (LbL) assembly. CHIT/ALG membranes were cross-linked with genipin at a concentration of 1 mg·mL {\textless} sup {\textgreater} -1 {\textless} /sup {\textgreater} or 5 mg·mL {\textless} sup {\textgreater} -1 {\textless} /sup {\textgreater} . Mass transport properties of glucose and oxygen were evaluated on the freestanding membranes. The diffusion of glucose and oxygen decreases with increasing cross-linking concentration. Mechanical properties were also evaluated in physiological-simulated conditions. Increasing cross-linking density leads to an increase of storage modulus, Young modulus, and ultimate tensile strength, but to a decrease in the maximum hydrostatic pressure. The in vitro biological performance demonstrates that cross-linked films are more favorable for cell adhesion. This work demonstrates the versatility and feasibility of LbL assembly to generate nanostructured constructs with tunable permeability, mechanical, and biological properties.

In this experimental phase equilibrium study, we show for the first time that it is possible to stabilize structure sH of hydrogen clathrate hydrate with the help of some selected promoters. It was established that the formation pressures of these systems are significantly higher than that of structure sII of hydrogen clathrate hydrate when tetrahydrofuran (THF) is used as a promoter. Although no experimental evidence is available yet, it is estimated that the hydrogen storage capacity of structure sH can be as high as 1.4 wt {%} of H 2 , which is about 40{%} higher compared to the hydrogen storage capacity in structure sH. © 2008 American Chemical Society.