The high prices currently achieved in the acquisition of non-renewable energy for electricity production and the low levels of energy efficiency in the housing sector are the national situation, which leads the Portuguese government to encourage the acquisition, the installation and the use of technologies which exploit indigenous and renewable energy. This study presents an application that was developed in order to help the citizen in his decision to invest in renewable technologies in their homes. The application is able to elaborate an economic analysis based on the selected type of renewable technology, providing the user with the knowledge of benefits and the annual costs involved in the system that he selected. This tool aims at facilitating the interaction of any user with such technologies and it can be used as a helpful tool to support the decision of investment in such systems.

n/a

n/a

n/a

n/a

Nanostructured silicon single junction thin film solar cells were deposited on commercial red clay roof tiles with engobe surfaces and earthenware wall tiles with glazed surfaces, with a test area of 24 mm 2. We studied the influence of the type of substrate tile, back contact, buffer layer and SiO x passivation layer on the optoelectronic performance of the solar cells. Despite the fact that typical micrometre-sized defects on the surfaces of the tiles and the porous nature of the ceramic substrates make deposition of homogeneous thin films on them quite challenging, we have been able to achieve a cell efficiency of 5% and a quantum efficiency of 80% on non-fully optimized cells on commercial tiles. The method is industrially employable utilizing pre-existing plasma-enhanced chemical vapour deposition technologies. The cost-effectiveness and industrial feasibility of the technique are discussed. Our study shows that photovoltaic tiles can combine energy generation with architectural aesthetics leading to significant implications for advancement in building integrated photovoltaics. © 2011 The Royal Society of Chemistry.

n/a

n/a

n/a

n/a

A commercial sheet of paper based on natural cellulose fibers acting as permeable membrane with thin film metal cathode (Cu) and anode (Al) layers in each face was used to produce paper batteries that could be interconnected in series and rechargeable using water as electrolyte. Their electrical characteristics and the set of electrochemical reactions that support the experimental behavior observed are described in this paper. A series of integrated batteries able to supply a voltage of about 3 V and a current ranging from 0.7 μA to 25 μA in cells with sizes of 1.2 cm × 3.0 cm for a relative humidity in the range of 50-65% were produced in a single sheet of paper, and successfully applied to control the ON/OFF gate state of paper transistors. © 2010 Elsevier Ltd. All rights reserved.

In software, hardware, and embedded system domains, debugging is the process of locating and correcting faults in a system. Depending on the context, the various characteristics of debugging induce different challenges and solutions. Post-silicon hardware debugging, for example, needs to address issues such as limited visibility and controllability, while debugging software entails other issues, such as the handling of distributed or non-deterministic computation. The challenges that accompany such issues are the focus of many current research efforts. Solutions for debugging range from interactive tools to highly analytic techniques. We have seen great advances in debugging technologies in recent years, but bugs continue to occur, and debugging still encompasses significant portions of the life-cycles of many systems. The session covered state-of-the-art approaches as well as promising new research directions in both the hardware and software domains.

This paper presents a step-up micro-power converter for solar energy harvesting applications. The circuit uses a SC voltage tripler architecture, controlled by an MPPT circuit based on the Hill Climbing algorithm. This circuit was designed in a 0.13 mu m CMOS technology in order to work with an a-Si PV cell. The circuit has a local power supply voltage, created using a scaled down SC voltage tripler, controlled by the same MPPT circuit, to make the circuit robust to load and illumination variations. The SC circuits use a combination of PMOS and NMOS transistors to reduce the occupied area. A charge re-use scheme is used to compensate the large parasitic capacitors associated to the MOS transistors. The simulation results show that the circuit can deliver a power of 1266 mu W to the load using 1712 mu W of power from the PV cell, corresponding to an efficiency as high as 73.91%. The simulations also show that the circuit is capable of starting up with only 19% of the maximum illumination level.

n/a

n/a

n/a

The accumulation of lead in several bones of Wistar rats with time was determined and comparedQ3 for the different types of bones. Two groups were studied: a control group (n = 20), not exposedto lead and a contaminated group (n = 30), exposed to lead from birth, first indirectly throughmother’s milk, and then directly through a diet containing lead acetate in drinking water (0.2%).Rats age ranged from 1 to 11 months, with approximately 1 month intervals and each of thecollections had 3 contaminated rats and 2 control rats. Iliac, femur, tibia–fibula and skull havebeen analysed by energy dispersive X-ray fluorescence technique (EDXRF). Samples offormaldehyde used to preserve the bone tissues were also analysed by Electrothermal AtomicAbsorption (ETAAS), showing that there was no significant loss of lead from the tissue to thepreservative. The bones mean lead concentration of exposed rats range from 100 to 300 mg g 1while control rats never exceeded 10 mg g 1. Mean bone lead concentrations were compared andthe concentrations were higher in iliac, femur and tibia–fibula and after that skull. However, ofall the concentrations in the different collections, only those in the skull were statisticallyQ4 significantly different (p o 0.05) from the other types of bones. Analysis of a radar chart alsoallowed us to say that these differences tend to diminish with age. The Spearman correlation testapplied to mean lead concentrations showed strong and very strong positive correlations betweenall different types of bones. This test also showed that mean lead concentrations in bones arenegatively correlated with the age of the animals. This correlation is strong in iliac and femur andvery strong in tibia–fibula and skull. It was also shown that the decrease of lead accumulationwith age is made by three plateaus of accumulation,

n/a

n/a

n/a

{We deduce a shallow water model, describing the motion of the fluid in a lake, assuming inflow-outflow effects across the bottom. This model arises from the asymptotic analysis of the 3D dimensional Navier-Stokes equations. We prove the global in time existence result for this model in a bounded domain taking the nonlinear slip/friction boundary conditions to describe the inflows and outflows of the porous coast and the rivers. The solvability is shown in the class of solutions with L(p)-bounded vorticity for any given p is an element of (1, infinity). Copyright (C) 2009 John Wiley & Sons, Ltd.}

n/a

This dissertation tries to track the route of power production from photovoltaic sources. A worldwide look into the photovoltaic solar power production is given. The theory behind the PV cell and its application in PV power modules is presented. The DC ? DC power converters usually associated with solar PV panels are showed. The main maximum power point tracking (MPPT) algorithms are also showed. A solar PV system was dimensioned using the theoretical models and the solar PV modules (BS ? 40) available at the Departamento de Engenharia Electrotécnica (DEE). This system was used as a reference for designing a simulator implemented in MatLab?Simulink. This simulator includes all the components needed to test the different MPP tracking algorithms. Those components are: A PV solar module, which can be associated with others to form a solar panel; A Flyback DC ? DC power converter and a classic perturb and observe (P&O) tracking algorithm. A solar power meter that gives values in W?m2 was built in order to validate simulation values of the solar PV modules. Measuring the solar module characteristics (tension ? current) and knowing the solar irradiation at that given time it is possible to check if the simulated values and the measured ones agree. With the data collected in the simulation a new MPP tracking algorithm was presented. This is based in the classic P&O algorithm, but using modules that try to overcome the local maxima problem. It also tries to minimize the control oscillations in the converter?inverter, this is done in order to minimize losses and to maximize power production.

n/a