n/a

n/a

n/a

n/a

n/a

In the recent past, multiple techniques and tools have been proposed and contributed to improve the distributed debugging functionalities, in several distinct aspects, such as handling the non-determinism, allowing cyclic interactive debugging of parallel programs, and providing more user-friendly interfaces. However, most of these tools are tied to a specific programming language and provide rigid graphical user interfaces. So they cannot easily adapt to support distinct abstraction levels or user interfaces. They also don't provide adequate support for cooperation with other tools in a software engineering environment. In this paper we discuss several dimensions which may contribute to develop more flexible distributed debuggers. We describe Fiddle, a distributed debugging tool which aims at overcoming some of the above limitations.

The triple-to-double ionization cross-section ratio of Li in the high-energy limit was computed in the sudden approximation with relativistic wave functions. Together with the calculated value of Dalgarno and Sadeghpour (Phys. Rev. A, 46 (1992) R3591), for the Li double-to-single ionization cross-section ratio, the value of 6.263x10-5 was obtained for the triple-to-single ionization cross-section ratio. This value is in full agreement with Wehlitz et al. experimental value of (6.38+-2.40)x10-5 obtained recently with synchrotron radiation (Phys. Rev. Lett., 81 (1998) 1813).

The changes occurring during the heating of a borosilicate glass have been investigated by differential thermal analysis, dilatometric analysis and thermomechanical analysis. The thermal properties of this glass, such as glass transition temperature, dilatometric softening temperature and linear thermal expansion coefficient, have been determined. Viscosity measurements in the temperature range 898-1048 K were performed in a thermomechanical analyser equipped with a penetration attachment for isothermal measurement, and from the temperature dependence of viscosity a value of 290 kJ mol-1 was obtained for the activation energy for viscous flow. Devitrification of the glass was observed, specifically in finely powdered glass samples, where the precipitation of cristobalite was identified by X-ray diffraction. Glass powder compacts sintered by viscous flow and cristobalite precipitation reduced strongly the shrinkage rate. © 2001 Elsevier Science B.V.

n/a

n/a

Hall effect measurements have been used to evaluate the conduction mechanism, exhibited by tin oxide thin film gas sensors deposited by spray pyrolysis. Two experiments have been carried out: (i) Hall measurements in air and (ii) in the presence of methane (first results reported), both as a function of temperature. From the measurements performed it was possible to infer the potential barrier and its dependence with the atmosphere used. The results obtained for the carrier concentration and mobility have been analysed in the light of the oxygen diffusion mechanism at grain boundaries by using the grain boundary-trapping model. In the presence of the methane gas the electrical resistivity decreases due to the lowering of the inter-grain boundary barrier height. © 2001 Published by Elsevier Science Ltd.

In the recent past, multiple techniques and tools have been proposed and contributed to improve the distributed debugging functionalities, in several distinct aspects, such as handling the non-determinism, allowing cyclic interactive debugging of parallel programs, and providing more user-friendly interfaces. However, most of these tools are tied to a specific programming language and provide rigid graphical user interfaces. So they cannot easily adapt to support distinct abstraction levels or user interfaces. They also don’t provide adequate support for cooperation with other tools in a software engineering environment. In this paper we discuss several dimensions which may contribute to develop more flexible distributed debuggers. We describe Fiddle, a distributed debugging tool which aims at overcoming some of the above limitations.

Water trees result from ac electrical aging of the polymeric insulation of medium and HV power cables in a humid or wet environment. As suggested by their name, they arise from penetration of water in the polymer. Visual observation with the help of an optical microscope shows tree (bush) type structures. This suggests that water trees might be fractal objects. Calculation of the fractal dimension from experimental samples may confirm the fractal characteristics and also give information on the damage caused to the polymer. In this work images of water trees taken under the optical microscope, dyed by methylene blue and etched for scanning electron microscopy (SEM), were studied in order to estimate the fractal dimension using a box-counting algorithm. The photographs, made using an optical microscope (scale of 100 mum), of the dyed samples were obtained from laboratory-aged low-density polyethylene (LDPE) specimens using accelerated techniques. Different field amplitude and frequency and also time of aging were used and the dimension values were compared. SEM images resulting from aged cross-linked polyethylene (XLPE) cables revealed a structure at a different scale (similar to 3 mum). Each photograph was analyzed to compare regions with and without water trees.

Water trees result from ac electrical aging of the polymeric insulation of medium and HV power cables in a humid or wet environment. As suggested by their name, they arise from penetration of water in the polymer. Visual observation with the help of an optical microscope shows tree (bush) type structures. This suggests that water trees might be fractal objects. Calculation of the fractal dimension from experimental samples may confirm the fractal characteristics and also give information on the damage caused to the polymer. In this work images of water trees taken under the optical microscope, dyed by methylene blue and etched for scanning electron microscopy (SEM), were studied in order to estimate the fractal dimension using a box-counting algorithm. The photographs, made using an optical microscope (scale of 100 mum), of the dyed samples were obtained from laboratory-aged low-density polyethylene (LDPE) specimens using accelerated techniques. Different field amplitude and frequency and also time of aging were used and the dimension values were compared. SEM images resulting from aged cross-linked polyethylene (XLPE) cables revealed a structure at a different scale (similar to 3 mum). Each photograph was analyzed to compare regions with and without water trees.

n/a

n/a

n/a

Coal fly ashes produced by an extinguished power plant in the north of Portugal have been melted with addition of CaCO3 and Na2CO3 to obtain glasses. One of the formulated compositions was selected for further studies and it was possible to manufacture glass-ceramics by crystallizing the parent glass through adequate time-temperature schedules. The macroscopic appearance, microstructure, mechanical, thermal and chemical properties indicated that these materials are quite attractive for cladding applications, exhibiting in some cases better performances than the conventional ceramic tiles.