Rodrigo Martins

This paper describes the development of a novel microfluidic platform for multifactorial analysis integrating four label-free detection methods: electrical impedance, refractometry, optical absorption and fluorescence. We present the rationale for the design and the details of the microfabrication of this multifactorial hybrid microfluidic chip. The structure of the platform consists of a three-dimensionally patterned polydimethylsiloxane top part attached to a bottom SU-8 epoxy-based negative photoresist part, where microelectrodes and optical fibers are incorporated to enable impedance and optical analysis. As a proof of concept, the chip functions have been tested and explored, enabling a diversity of applications: (i) impedance-based identification of the size of micro beads, as well as counting and distinguishing of erythrocytes by their volume or membrane properties; (ii) simultaneous determination of the refractive index and optical absorption properties of solutions; and (iii) fluorescence-based bead counting. © 2016 by the authors.

The present work reports the influence of zinc oxide (ZnO) seed layer annealing temperature on structural, optical and electrical properties of ZnO nanorod arrays, synthesized by hydrothermal method assisted by microwave radiation, to be used as UV sensors. The ZnO seed layer was produced using the spin-coating method and several annealing temperatures, ranging from 100 to 500 °C, have been tested. X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and spectrophotometry measurements have been used to investigate the structure, morphology, and optical properties variations of the produced ZnO nanorod arrays regarding the seed layer annealing temperatures employed. After the growth of ZnO nanorod arrays, the whole structure was tested as UV sensors, showing an increase in the sensitivity with the increase of seed layer annealing temperature. The UV sensor response of ZnO nanorod arrays produced with the seed layer annealed temperature of 500 °C was 50 times superior to the ones produced with a seed layer annealed at 100 °C. © 2016 by the authors.

The charge transfer dynamics at interfaces are fundamental to know the mechanism of photovoltaic processes. The internal potential in solar cell devices depends on the basic processes of photovoltaic effect such as charge carrier generation, separation, transport, recombination, etc. Here we report the direct observation of the surface potential depth profile over the cross-section of the ZnO nanorods/Cu2O based solar cell for two different layer thicknesses at different wavelengths of light using Kelvin probe force microscopy. The topography and phase images across the cross-section of the solar cell are also observed, where the interfaces are well-defined on the nanoscale. The potential profiling results demonstrate that under white light illumination, the photoinduced electrons in Cu2O inject into ZnO due to the interfacial electric field, which results in the large difference in surface potential between two active layers. However, under a single wavelength illumination, the charge carrier generation, separation, and transport processes between two active layers are limited, which affect the surface potential images and corresponding potential depth profile. Because of changes in the active layer thicknesses, small variations have been observed in the charge carrier transport mechanism inside the device. These results provide the clear idea about the charge carrier distribution inside the solar cell in different conditions and show the perfect illumination condition for large carrier transport in a high performance solar cell. © 2016 American Chemical Society.

Abstract: The present work reports the synthesis of zinc oxide (ZnO) nanoparticles with hexagonal wurtzite structure considering a solvothermal method assisted by microwave radiation and using different solvents: water (H2O), 2-ethoxyethanol (ET) and ethylene glycol (EG). The structural characterization of the produced ZnO nanoparticles has been accessed by scanning electron microscopy, X-ray diffraction, room-temperature photoluminescence and Raman spectroscopies. Different morphologies have been obtained with the solvents tested. Both H2O and ET resulted in rods with high aspect ratio, while EG leads to flower-like structure. The UV absorption spectra showed peaks with an orange shift for synthesis with H2O and ET and blue shift for synthesis with EG. The different synthesized nanostructures were tested for photocatalyst applications, revealing that the ZnO nanoparticles produced with ET degrade faster the molecule used as model dye pollutant, i.e. methylene blue. Graphical Abstract: [Figure not available: see fulltext.] © 2015 Springer Science+Business Media New York

Here we present for the first time a TiO2/Cu2O all-oxide heterojunction solar cell entirely produced by spray pyrolysis onto fluorine doped tin oxide (FTO) covered glass substrates, using silver as a back contact. A combinatorial approach was chosen to investigate the impact of the TiO2 window layer and the Cu2O light absorber thicknesses. We observe an open circuit voltage up to 350 mV and a short circuit current density which is strongly dependent of the Cu2O thickness, reaching a maximum of  0.4 mA/cm2. Optical investigation reveals that a thickness of 300 nm spray pyrolysis deposited Cu2O is sufficient to absorb most photons with an energy above the symmetry allowed optical transition of 2.5 eV, indicating that the low current densities are caused by strong recombination in the absorber that consists of small Cu2O grains. © 2014 Elsevier Ltd. All rights reserved.

We present the results obtained with an extended-gate ISFET totally based on amorphous oxides (GIZO as the semiconductor, +{\hbox{Ta}}-{2}{\hbox{O}}-{5}{\ hbox{:SiO}}-inf2-inf as the dielectric and +{\hbox{Ta}}-{2}{\hbox{O}}-inf5-inf as the sensitive layer). A full characterization of the device was performed with constant ionic strength pH buffer solutions, revealing a sensitivity of 40 mV/pH with small hysteresis, and good linearity in the pH 4-pH 10 range buffer solutions. These results clearly show that it is possible to produce room-temperature disposable and low cost bio-sensors. © 2005-2012 IEEE.

In this work, we report results concerning the performances of thin-film transistors (TFTs) where the channel layer is based on microcrystalline zinc tin oxide (ZTO) processed by spray pyrolysis technique. TFTs made with 30 nm thick ZTO channel layer deposited at a substrate temperature of 400 C and 300 Cexhibited, respectively, a saturation mobility of 2.9 cm V s and 1.45 cm V s ; voltage of 0.15 V, and 0.2 V; a sub-threshold swing of 400 mV/dec and 500 mV/dec; ON/OFF ratio at the onset of hard saturation current of 3.5 10 and 6 10 , for a drain to source voltage of 10 V (close to or below the gate to source voltage). This indicates that the substrate temperature is relevant in determining the devices' electronic performances. © 2013 IEEE.

This paper deals with high transparent and high conductive oxides based on polycrystalline titanium (Ti) doped (0.5-3 at.%) indium oxide (IO) thin films produced on glass substrates at 400 °C by spray pyrolysis technique. X-ray diffraction analysis confirmed the cubic bixbyite structure of indium oxide. A high mobility of ∼ 97 cm2 V- 1 s- 1, a carrier concentration of ∼ 1.55 × 1020 cm- 3 and a resistivity of ∼ 4.11 × 10- 4 Ω-cm with ∼ 83% of transmittance in the wavelength ranging between 400 and 2500 nm were obtained for 2 at.% Ti doping films, rivalling so to the best known transparent conducting oxide based on indium tin oxide. Moreover, the transmittance in the broad wavelength ranging between 400 and 2500 nm is over 83%, leading so to an increasing carrier generation towards the near infrared region of the spectrum, as required for applications such as solar cells. We also notice that increasing the doping concentration widened the optical band gap and caused a small Burstein-Moss shift, due to mobility decrease, as expected. © 2012 Published by Elsevier B.V.

In this work we present sputtered multicomponent dielectrics based on mixtures of HfO 2 and SiO 2. This way it is possible to get stable amorphous structure up to 800°C, that does not happen for pure HfO 2, for instance, that present a polycrystalline structure when deposited without any intentional substrate heating. Besides, also the band gap of the resulting films is increased when compared with pure HfO2 that theoretically is an advantage in getting a suitable band offset with the semiconductor layer on oxide TFTs. Concerning the electrical characterization, the leakage current on c-Si MIS structures is low as 10 -9 Acm -2 at 10 V. The amorphous structure of the films also lead to better dielectric/semiconductor interfaces, as suggested by C-V characteristics on GIZO MIS structures, which do not present strong variation with frequency. On other hand, the dielectric constant decreases due to the incorporation of SiO 2 and Al 2O 3. Further improvement on insulating and interface characteristics is achieved using multilayer stacks and substrate bias during deposition. © 2012 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

The high visible-near infrared transparent and high carrier mobility (μ) Mo doped (0.5 at%) indium oxide (IMO) films were deposited by the spray pyrolysis technique. The deposited films were irradiated by 50MeV Li 3+ ions with different fluences of 1×1011, 1×1012 and 1×1013 ions cm-2. X-ray diffraction analysis confirmed the cubic bixbyite structure of indium oxide. A fascinating feature is that the ion irradiation process has introduced a fraction of the molybdenum oxide phase. The μ of as-deposited IMO films is decreased from ̃122.4 to 93.3 cm2 V-1 s-1, following the ion irradiation. The theoretically calculated μ and carrier density values were correlated with those measured experimentally. The transport mechanism has been analysed based on the ionized and neutral impurity scattering centres. The average transmittance (400-2500 nm) of the as-deposited IMO films is decreased from 83% to 60% following irradiation. © 2011 IOP Publishing Ltd.

High visible to near infrared (NIR) transparent Mo (0-1 at%) doped In2O3 (IMO) thin films with high carrier mobility were deposited on Corning-1737 glass substrates at 400 °C by spray pyrolysis experimental technique. The films were annealed in vacuum (∼1×10-4 mbar) at 550 °C for 45 min. XRD analysis confirmed that indium oxide belongs to cubic bixbyite structure. The preferred growth orientation along (2 2 2) plane for low Mo doping level shifts to (4 0 0) for higher Mo doping levels. Crystallite sizes extracted from the XRD data corroborate the changes in full-width at half-maximum due to the variation in Mo doping. Scanning electron microscopy study illustrates the evolution in surface microstructures as a function of Mo doping. The negative sign of Hall coefficient confirmed n-type conductivity. Films with high mobility of ∼149 cm2/(V s), carrier concentration of ∼1.0×1020 cm-3, resistivity of ∼4.0×10-4 Ω cm and high figure of merit of ∼1.02×10-2 Ω-1 were observed for post-annealed films (0.5 at% Mo). The obtained high average transparency of ∼83% in the wavelength range 400-2500 nm confirms that transmittance is well extended into the NIR region. © 2009 Elsevier B.V. All rights reserved.

Nanostructured silicon (na-Si:H) thin films were fabricated using plasma enhanced chemical vapour deposition (PECVD) technique under high silane hydrogen dilution and a discharge frequency of 27 MHz, where the substrate was located in the dark region of the plasma, protected by a grounded metal grid. By not exposing the growth surface directly to the plasma we avoid the silicon growth surface to sustain a high ion bombardment leading to a less defective surface and highly compact films. The intrinsic films grown under these conditions were used to produce the channel region of thin film transistors (TFTs) with a bottom gate staggered configuration, integrating different dielectric layers. The devices produced exhibit a field effect mobility close to 1.84 cm 2 V -1S -1, threshold voltage around 2 V, on/off ratio above 10 7 and sub-threshold slope below 0.5 V/decade, depending on the dielectric used. Copyright © 2010 American Scientific Publishers All rights reserved.

Molybdenum doped indium oxide (IO) thin films were deposited on the Coring F1737 glass substrates at 400 °C by spray pyrolysis technique. TheModoping was varied between 0 and 4 at.%. The films were characterized by their structural, electrical and optical properties. The films are confirmed to be cubic bixbyite In 2O 3 with a strongest orientation along (222) for 0.5 at.% Mo, which is shifted to (400) plane when the Mo doping is increased to ≥1.2 at.%. The films deposited with 0.5 at.% Mo showed high mobility of ̃90 cm 2/Vs, resistivity of ̃6.8×10 -4ωcm and carrier concentration of ̃1.01× 1020 cm -3 with >̃73% transmittance in the visible range between 500 and 800 nm. The transmittance is well extended into near infrared region.

Molybdenum (0-1 at. %) doped indium oxide thin films with high near-infrared (NIR) transparency and high carrier mobility were deposited on Corning-1737 glass substrates at 400 °C by a spray pyrolysis experimental technique. X-ray diffraction (XRD) analysis confirmed the cubic bixbyite structure of indium oxide. The preferred growth orientation along the (222) plane for the low Mo doping level (0.5 at. %) shifts to (400) for higher Mo doping levels (<0.6 at. %). The crystallite size extracted from the XRD data corroborates the changes in full width at half maximum due to the variation in Mo doping. A scanning electron microscopy study illustrated the evolution in the surface microstructure as a function of Mo doping. The negative sign of the Hall coefficient confirmed the n -type conductivity. A high carrier mobility of ∼122.4 cm2 /V s, a carrier concentration of ∼9.5× 1019 cm-3, a resistivity of ∼5.3× 10-4cm, and a high figure of merit of ∼4.2× 10-2 -1 are observed for the films deposited with 0.5 at. % Mo. The obtained high average transparency of ∼83% in the wavelengths ranging from 400 to 2500 nm confirmed the extension of transmittance well into the NIR region. © 2009 American Institute of Physics.

Molybdenum-doped indium oxide (IMO) thin films were deposited at 450 °C for varying molybdenum concentrations in the range of 0.5-2 at% by the spray pyrolysis technique. These films confirmed the cubic bixbyite structure of polycrystalline In2O3. The preferred growth orientation along the (2 2 2) plane shifts to (4 0 0) on higher Mo doping levels. The films doped with 0.5 at% Mo showed high mobility of 76.9 cm2/(V s). The high visible transmittance extends well into the near-infrared region. A possibility of using the produced IMO films in nanocrystalline (nc) silicon solar cell applications is discussed in this article. The morphological studies showed a change in the microstructure, which is consistent with the change in crystallographic orientation. © 2008 Elsevier B.V. All rights reserved.

Hafnium oxide-aluminum oxide (HfAlO) dielectric films were cosputtered using HfO2 and Al2 O3 targets, and their properties are studied in comparison with pure HfO2 films. The X-ray diffraction studies confirmed that the HfO2 films are nanocrystalline with a monoclinic phase. The as-deposited HfAlO films with a chemical composition of (HfO2) 0.86 (Al2 O3) 0.14 are amorphous even after annealing at 500°C. Further, the cosputtered films show a slight reduction in leakage current. The leakage current density may be significantly reduced below 3× 10-10 A cm-2 at an electric field of 0.25 MV/cm when applying the proper radio-frequency bias to the substrate. © 2009 The Electrochemical Society.

Molybdenum doped (0-1 at. %) indium oxide thin films with high near infrared (NIR) transparency and carrier mobility were deposited on Corning-1737 glass substrates at 400 °C by spray pyrolysis experimental technique. Films with mobility as high as ∼149 cm2 /V s were obtained when annealed in vacuum at 550 °C, which also possess carrier concentration of ∼1× 1020 cm-3 and resistivity as low as ∼4.0× 10-4 cm. Further, both the average visible transmittance (500-800 nm) and the average NIR transmittance are >83%. This clearly shows that the transmittance is extended well into the NIR region. © 2009 American Institute of Physics.

In this work, we present the structural and electrical properties of HfO 2, HfO 2 +SiO 2, and HfO 2 +Al 2O 3 dielectric composite layers deposited by sputtering without any intentional substrate heating. The films were deposited on glass and 〈100〉 crystalline silicon (c-Si) substrates from ceramic targets by using argon (Ar) and oxygen (O 2) as sputtering and reactive gases, respectively. The incorporation of SiO 2 and Al 2O 3 into hafnia was obtained by co-sputtering and itwas controlled by adjusting the ratio of r.f. power applied between the targets. The HfO 2 films present a microcrystalline structure, when deposited at room temperature (RT). The lowest leakage current in c-Si MIS (Metal-Insulator- Semiconductor) structures (below 10 9A/cm 2 at 10V on films with a thickness around 180 nm) was obtained for an Ar/O 2 ratio of 14:1 sccm, and further increase in O 2 flow does not enhance the electrical characteristics. The codeposition of SiO 2 or Al 2O 3 with hafnia has a strong influence on the structure of the resulting films since they become amorphous. The leakage current in MISstructures incorporating these multi-component dielectrics is reduced at least by a factor of 2, which is accompanied by an increase on the band gap. The dielectric constant is decreased due to the lower values for SiO 2 and Al 2O 3. © 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

In the present work we investigate, the role of zinc oxide (ZnO) thin films passivating layer deposited by rf magnetron sputtering at room temperature on low (18%) and high (80%) porosity porous silicon (PS). The micro-Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM) analysis have been carried out to understand the effect of ZnO films coating on PS. A systematic investigation from Raman spectroscopy suggests the formation of a good quality ZnO wurtzite structure on PS. The photoluminescence (PL) measurements on PS and ZnO coated PS shows a red, blue and UV emission bands at around ∼1.8, ∼2.78 and ∼3.2 eV. An enhancement of all PL emission bands have been achieved after ZnO films deposition on high porosity PS. © 2007 Elsevier B.V. All rights reserved.

This work refers to the fabrication of hybrid solar cells based on porous silicon (PS) filled with copper phthalocyanine (CuPc) to form GZO/CuPc-PS/Si/Al structure. We used n-type Si since photoinduced charge transfer from CuPc to Si is observed only for n-type Si. The characteristic 100% peak at 6.8°2θ from XRD confirms that the CuPc coating on PS exists in α-CuPc polymorph. The systematic increase in FWHM of XRD peak at 69.1°2θ and red-shift of LO phonon Raman spectra indicate a progressive reduction of Si nanocrystallites size with increasing etching time and the estimated size agrees well with atomic force microscopic images. The FTIR results confirm the formation of α-CuPc polymorph and it is also corroborated well with XRD and Raman results. © 2008.

In this work the electrical and structural properties of two high k materials as hafnium oxide (HfO2) and tantalum oxide (Ta2O5) produced at room temperature are exploited. Aiming low temperature processing two techniques were employed: r.f. sputtering and electron beam evaporation. The sputtered HfO2 films present a nanocrystalline structure when deposited at room temperature. The same does not happen for the evaporated films, which are essentially amorphous. The density and the electrical performance of both sputtered and evaporated films are improved after annealing them at 200 °C. On the other hand, the Ta2O5 samples deposited at room temperature are always amorphous, independently of the technique used. The density and electrical performance are not so sensitive to the annealing process. The set of data obtained show that these dielectrics processed at temperatures below 200 °C present promising properties aiming to produce devices at low temperature with improved interface properties and reduced leakage currents. © 2007 Elsevier B.V. All rights reserved.

Molybdenum doped indium oxide (IMO) thin films were deposited on the glass substrates preheated to 450 °C by spray pyrolysis technique. The Mo doping was varied between 0 and 2.0 at.%. The films were characterized by their structural, electrical and optical properties. The films are confirmed to be cubic bixbyite In2O3 with a strongest orientation along (222) plane, which is shifted to (400) plane for the increase in Mo doping to 1.25 and 2 at.%. The film deposited with 0.5 at.% Mo doping shows high mobility of 76.9 cm2V- 1s- 1 , resistivity of 1.8 × 10- 3 Ω-cm and high carrier concentration of 4.6 × 1019 cm- 3 with 81.3% transmittance in the visible range between 500 and 800 nm. Further, the transparency extents well into the near-IR range. © 2008 Elsevier B.V. All rights reserved.

In the present work, we investigate the influence of hydrocarbon (CHx) thin film coating on porous silicon (PS) by plasma enhanced chemical vapor deposition (PECVD) technique to detect CO2 gas. The fabricated CHx/PS heterojunction device shows up to one and two orders of magnitude enhancement in current under CO2 gas exposure. FTIR spectroscopy measurements reveal a remarkable structural modification of the CHx/PS device during CO2 gas exposure. Further, the enhancement of CHx related absorbance bands by a factor 6.2 for the CHx/PS specimen in comparison with PS confirm the good quality of the deposited CHx thin films. © 2007 Elsevier B.V. All rights reserved.

In this work, it is demonstrated the application of a high k dielectric, as hafnium oxide (HfO2), in poly-Si thin film transistors (TFTs) obtained by metal induced lateral crystallization (MILC). The dielectric layer was deposited at room temperature by sputtering, using argon and oxygen as process gases. As produced TFTs exhibit field effect mobility around 45 cm2 V-1 s-1and Ion/Ioff ratio of about 2 × 105. After annealing in a forming gas atmosphere for about 1 h at 200 °C, the threshold voltage and the sub-threshold slope are reduced, respectively from 4.8 to 2 V and from 1.6 to 1.4 V/dec. Nevertheless, by doing so, we notice a reduction on the field effect mobility of about 45% and a decrease of about 2.5 times on the Ion/Ioff ratio. Longer annealing time will not improve the TFT's performance. © 2008 Elsevier B.V. All rights reserved.

In this paper a new approach is presented for the simulation of spectroscopic ellipsometry (SE) data to estimate the level of nickel (Ni) contamination in silicon crystallized by metal induced crystallization (MIC). The method employs the addition of Ni as reference for a Bruggemann effective medium approximation (BEMA) to simulate the optical response of the crystallized silicon. This new approach is sensitive to changes in the initial average metal thickness used on the crystallization process to thickness values as low as 0.05 nm. This corresponds to a volume fraction of 0.24%, confirmed by Rutherford backscattering spectrometry (RBS) where it was observed that the Ni volume fraction detected by SE varies linearly with the metal amount inside the crystallized films determined by RBS. © 2008.