Rodrigo Martins

The aim of this paper is to study the role of different metals (aluminium, molybdenum, nickel and titanium) in inducing crystallization in films produced by LPCVD at high and low temperature processes and to compare the structural, morphological, optical and electrical properties of the various films produced. This work envisages the use of the most suitable conditions that lead to the production of films for optoelectronic applications such as solar cells. © 2003 Elsevier B.V. All rights reserved.

In this work, we present the structural and electrical properties of HfO 2, HfO 2 +SiO 2, and HfO 2 +Al 2O 3 dielectric composite layers deposited by sputtering without any intentional substrate heating. The films were deposited on glass and 〈100〉 crystalline silicon (c-Si) substrates from ceramic targets by using argon (Ar) and oxygen (O 2) as sputtering and reactive gases, respectively. The incorporation of SiO 2 and Al 2O 3 into hafnia was obtained by co-sputtering and itwas controlled by adjusting the ratio of r.f. power applied between the targets. The HfO 2 films present a microcrystalline structure, when deposited at room temperature (RT). The lowest leakage current in c-Si MIS (Metal-Insulator- Semiconductor) structures (below 10 9A/cm 2 at 10V on films with a thickness around 180 nm) was obtained for an Ar/O 2 ratio of 14:1 sccm, and further increase in O 2 flow does not enhance the electrical characteristics. The codeposition of SiO 2 or Al 2O 3 with hafnia has a strong influence on the structure of the resulting films since they become amorphous. The leakage current in MISstructures incorporating these multi-component dielectrics is reduced at least by a factor of 2, which is accompanied by an increase on the band gap. The dielectric constant is decreased due to the lower values for SiO 2 and Al 2O 3. © 2009 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

In this work, HfO2 was deposited by r.f. sputtering at room temperature and then annealed for different times at 200°C in a forming gas atmosphere. After annealing for 2 hours the HfO2 layers present a reduction on the flat band voltage of about 1 V, relatively to the as deposited film, decreasing from -2.23V down to -1.28 V. This means an improvement of the interface properties and a reduction on the oxide charge density from 1.33×1012 cm-2 to 7.62×1011 cm -2. The dielectric constant reaches a maximum of 18.3 after 5h annealing due to film's densification. When annealing for longer times such as 10h a small degradation of the electrical properties is observed. After 10h annealing the dielectric constant, flat band voltage and fixed charge density are respectively, 14.9, -2.96 V and 1.64×1012 cm-2 and the leakage current also increases due to film's crystallization.

Nanostructured silicon (na-Si:H) thin films were fabricated using plasma enhanced chemical vapour deposition (PECVD) technique under high silane hydrogen dilution and a discharge frequency of 27 MHz, where the substrate was located in the dark region of the plasma, protected by a grounded metal grid. By not exposing the growth surface directly to the plasma we avoid the silicon growth surface to sustain a high ion bombardment leading to a less defective surface and highly compact films. The intrinsic films grown under these conditions were used to produce the channel region of thin film transistors (TFTs) with a bottom gate staggered configuration, integrating different dielectric layers. The devices produced exhibit a field effect mobility close to 1.84 cm 2 V -1S -1, threshold voltage around 2 V, on/off ratio above 10 7 and sub-threshold slope below 0.5 V/decade, depending on the dielectric used. Copyright © 2010 American Scientific Publishers All rights reserved.

In this work metal induced crystallization was studied using aluminium and gold deposited over 150 nm amorphous silicon films grown by LPCVD. Aluminium and gold layers with thickness between 1 and 5 nm were deposited on the silicon films and after that, the samples were annealed at 500°C from 5 up to 30 h. When the crystallization is induced through a gold layer, the Si crystalline fraction is higher than when using aluminium. For samples crystallized for 30 h at 500°C with 2 nm of metal a crystalline fraction of 57.5% was achieved using gold and only 38.7% when using aluminium. © 2005 Springer Science + Business Media, Inc.

In this work we present sputtered multicomponent dielectrics based on mixtures of HfO 2 and SiO 2. This way it is possible to get stable amorphous structure up to 800°C, that does not happen for pure HfO 2, for instance, that present a polycrystalline structure when deposited without any intentional substrate heating. Besides, also the band gap of the resulting films is increased when compared with pure HfO2 that theoretically is an advantage in getting a suitable band offset with the semiconductor layer on oxide TFTs. Concerning the electrical characterization, the leakage current on c-Si MIS structures is low as 10 -9 Acm -2 at 10 V. The amorphous structure of the films also lead to better dielectric/semiconductor interfaces, as suggested by C-V characteristics on GIZO MIS structures, which do not present strong variation with frequency. On other hand, the dielectric constant decreases due to the incorporation of SiO 2 and Al 2O 3. Further improvement on insulating and interface characteristics is achieved using multilayer stacks and substrate bias during deposition. © 2012 Copyright Society of Photo-Optical Instrumentation Engineers (SPIE).

In this work, metal induced crystallization using nickel was employed to obtain polycrystalline silicon by crystallization of amorphous films for thin film transistor applications. The devices were produced through only one lithographic process with a bottom gate configuration using a new gate dielectric consisting of a multi-layer of aluminum oxide/titanium oxide produced by atomic layer deposition. The best results were obtained for TFTs with the active layer of poly-Si crystallized for 20 h at 500 °C using a nickel layer of 0.5 nm where the effective mobility is 45.5 cm2 V-1 s-1. The threshold voltage, the on/off current ratio and the sub-threshold voltage are, respectively, 11.9 V, 5.55×104 and 2.49 V/dec. © 2005 Elsevier B.V. All rights reserved.

The aim of this work is to study the electrical characteristics of polycrystalline silicon (poly-Si) thin film transistors (TFTs) using spectroscopic impedance technique, where the poly-Si active layer was obtained by metal induced crystallization of amorphous silicon. From the study performed a theoretical model that fitted the impedance data is proposed, in order to obtain the separate contributions of each region that constitutes the TFT namely the channel, non accumulated region and contacts. © 2006 Elsevier B.V. All rights reserved.

In this paper we present results concerning the optimisation of the electronic and mechanical properties presented by amorphous silicon (a-Si:H) thin films produced on polyimide (Kapton® VN) substrates with different thicknesses (25, 50 and 75 μm) by the plasma enhanced chemical vapour deposition (PECVD) technique. The purpose of this study is to obtain a low defect density as well as low residual stresses (specially at the interface) in order to provide good performances for large area (10 mm wide by 80 mm long) flexible position sensitive detectors. The electrical and optical properties presented by the films will be correlated to the sensor characteristics. The properties of samples have been measured by dark/photoconductivity, constant photocurrent measurements (CPM) and the results have been compared with films deposited on Corning 7059 glass substrates during the same run deposition. The residual stresses were measured using an active optical triangulation and angle resolved scattering. The preliminary results indicate that the thinner polymeric substrate with 25 μm presents the highest density of states, which is associated to the residual stresses and strains associated within the film. © 2002 Elsevier Science B.V. All rights reserved.

In this work metal induced crystallization (MIC) using nickel (Ni) was employed to obtain poly-Si by crystallization of amorphous films for application as active layer in TFTs. Ni layers with thicknesses of 0.5 nm, 1 nm and 2 nm were used to crystallize the silicon. The TFTs were produced with a bottom gate configuration using a multi-layer Al2O3/TiO2 insulator produced by atomic layer deposition (ALD) as gate dielectric. The best performances of the TFT produced were obtained when using very thin Ni layers for the crystallization. This is attributed to a lower metal contamination and to the enhancement of grain size, as a result of the lower nucleation density achieved, when using the thinnest Ni layer. Devices that exhibit effective mobility of 45.5 cm2V-1s-1 and an on/off ratio of 5.55×104 were produced using a 0.5 nm Ni layer to crystallize the active channel area.

The aim of this paper is to study the role of gold (Au) induced crystallization on amorphous silicon (a-Si) films produced by low pressure chemical vapor deposition (LPCVD) at low process temperatures (550 °C) to allow the use of glass substrates. Concerning the crystallization process Au was deposited by e-beam thermal evaporation over the silicon (Si), using different metal thickness, from 5 to 100 Å. The samples were then annealed at 450, 500 and 550 °C and the crystallization time was changed from 5 up to 30 h. The structure of the films was analyzed by X-ray diffraction (XRD) and spectroscopic ellipsometry (SE) while electrical conductivity measurements were performed to obtain the electrical properties of the films produced, namely the activation energy (EA) and how it changes with the Au thickness used. The data achieved show that the increase of the metal layer thickness decreases the time needed to get full crystallization. However this leads to lower conduction activation energy (EA) meaning that there is also an increase of Au incorporation that leads to the production of doped films. © 2004 Elsevier B.V. All rights reserved.

This paper deals with the role the substrate on the structure of undoped and n-doped polycrystalline silicon (poly-Si) films produced by Low Pressure Chemical Vapour Deposition (LPCVD). The structural and electrical properties of the films deposited on glass, glass covered with molybdenum (Mo), oxidised crystalline silicon and oxidised crystalline silicon covered with Mo were analysed using X-ray diffraction and Spectroscopic Ellipsometry, dark conductivity and Hall effect measurements. Undoped poly-Si films deposited over Mo present modifications in the crystalline structure relatively to those deposited on the other substrates. The presence of Mo changes the preferential growth orientation, enhancing the Si {111} grains orientation, leading to more compact films. The electrical measurements also confirm that the films grown on Mo substrates present better characteristics. Some differences are also observed during the initial growth stages when using glass or oxidised silicon. Very thin n-doped films present a less effective doping effect when deposited on oxidised silicon than the ones deposited on glass substrates.

In this paper a new approach is presented for the simulation of spectroscopic ellipsometry (SE) data to estimate the level of nickel (Ni) contamination in silicon crystallized by metal induced crystallization (MIC). The method employs the addition of Ni as reference for a Bruggemann effective medium approximation (BEMA) to simulate the optical response of the crystallized silicon. This new approach is sensitive to changes in the initial average metal thickness used on the crystallization process to thickness values as low as 0.05 nm. This corresponds to a volume fraction of 0.24%, confirmed by Rutherford backscattering spectrometry (RBS) where it was observed that the Ni volume fraction detected by SE varies linearly with the metal amount inside the crystallized films determined by RBS. © 2008.

Doped and undoped a-Si:H and a-SiC:H films were deposited by R. F. decomposition of silane and silane/methane mixtures respectively, in a two consecutive (decomposition and deposition) chambers glow discharge capacitively coupled system. Their electro-optical properties were extensively investigated through dark conductivity, photoconductivity, spectral response, optical absorption, R. F. transmission spectra, electron spin ressonance and CxV MOS measurements.

Abstract: The present work reports the synthesis of zinc oxide (ZnO) nanoparticles with hexagonal wurtzite structure considering a solvothermal method assisted by microwave radiation and using different solvents: water (H2O), 2-ethoxyethanol (ET) and ethylene glycol (EG). The structural characterization of the produced ZnO nanoparticles has been accessed by scanning electron microscopy, X-ray diffraction, room-temperature photoluminescence and Raman spectroscopies. Different morphologies have been obtained with the solvents tested. Both H2O and ET resulted in rods with high aspect ratio, while EG leads to flower-like structure. The UV absorption spectra showed peaks with an orange shift for synthesis with H2O and ET and blue shift for synthesis with EG. The different synthesized nanostructures were tested for photocatalyst applications, revealing that the ZnO nanoparticles produced with ET degrade faster the molecule used as model dye pollutant, i.e. methylene blue. Graphical Abstract: [Figure not available: see fulltext.] © 2015 Springer Science+Business Media New York

In this paper we present the effect of thickness on the electrical and optical properties of intrinsic/nondoped zinc oxide thin films deposited at room temperature by radio frequency magnetron sputtering, able to be used as a semiconductor material on electronic devices, like for example ozone gas sensors and ultraviolet detectors. These films are polycrystalline with a c-axis preferential orientation parallel to the substrate. The films present a resistivity that varies from 5.0 × 104 Ω cm to 1.0 × 109 Ω cm with an optical visible transmittance of 85%. The sensor response exceeds more than five orders of magnitude when exposed to UV light recovering to the initial state in the presence of ozone. © 2006 Elsevier B.V. All rights reserved.

The present work reports the influence of zinc oxide (ZnO) seed layer annealing temperature on structural, optical and electrical properties of ZnO nanorod arrays, synthesized by hydrothermal method assisted by microwave radiation, to be used as UV sensors. The ZnO seed layer was produced using the spin-coating method and several annealing temperatures, ranging from 100 to 500 °C, have been tested. X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM) and spectrophotometry measurements have been used to investigate the structure, morphology, and optical properties variations of the produced ZnO nanorod arrays regarding the seed layer annealing temperatures employed. After the growth of ZnO nanorod arrays, the whole structure was tested as UV sensors, showing an increase in the sensitivity with the increase of seed layer annealing temperature. The UV sensor response of ZnO nanorod arrays produced with the seed layer annealed temperature of 500 °C was 50 times superior to the ones produced with a seed layer annealed at 100 °C. © 2016 by the authors.

In this paper we present results of intrinsic/non doped zinc oxide films deposited at room temperature by rf magnetron sputtering able to be used as a truly semiconductor on electronic devices like ozone gas sensors and ultra-violet detectors. The produced films are polycrystalline with a c-axis preferential orientation parallel to the substrate. The films' resistivity varies from 4.0×10-2 Ωcm to 1.0×10-9 Ωcm, depending on the deposition conditions used (rf power density and oxygen partial pressure), which turns not affecting the optical properties (in average a transmittance of around 85 % and an optical band gap of about 3.44 eV, independent of the deposition conditions used). When exposed to UV light the sensor response based on these films may exceed more than 5 orders of magnitude, recovering to the initial state in the presence of ozone. The sensitivity of the films is improved when the oxygen partial pressure increases and the rf power density used decreases, due to changes on the structural properties of the films. © 2006 Materials Research Society.

In this paper we present results of intrinsic/non-doped zinc oxide deposited at room temperature by radio frequency magnetron sputtering able to be used as a semiconductor material on electronic devices, like for example ozone gas sensors, ultra-violet detectors and thin film transistors. These films present a resistivity as high as 2.5×108 Ω cm with an optical transmittance of 90%. Concerning the structural properties, these films are polycrystalline presenting a uniform and very smooth surface. © 2005 Elsevier B.V. All rights reserved.

We present the results obtained with an extended-gate ISFET totally based on amorphous oxides (GIZO as the semiconductor, +{\hbox{Ta}}-{2}{\hbox{O}}-{5}{\ hbox{:SiO}}-inf2-inf as the dielectric and +{\hbox{Ta}}-{2}{\hbox{O}}-inf5-inf as the sensitive layer). A full characterization of the device was performed with constant ionic strength pH buffer solutions, revealing a sensitivity of 40 mV/pH with small hysteresis, and good linearity in the pH 4-pH 10 range buffer solutions. These results clearly show that it is possible to produce room-temperature disposable and low cost bio-sensors. © 2005-2012 IEEE.

In this work, we investigate the role of amorphous silicon (a-Si:H) thin films deposited by a plasma enhanced chemical vapor deposition (PECVD) technique on porous silicon (PS) to facilitate its water vapor and oxygen gas sensing properties using its electrical response. Overall we notice a rectifying behavior from a-Si:H/PS heterojunction device, where a current enhancement of one and four orders of magnitude was observed in the presence of oxygen gas and water vapor, in comparison with atmospheric air at room temperature, respectively. The photoluminescence (PL) investigation of PS shows a slight blue shift in the PL emission band from 1.72 to 1.77 eV and the intensity of the PL is enhanced by a factor of 5.4 with increase of porosity from 21% to 77%. This PL emission may originate from the O-Si-H related absorbance bands. Alternatively, quenching of the PL intensity was observed after a-Si:H films were deposited on PS specimens. Besides, micro-Raman and atomic force microscopic (AFM) analyse were carried out to understand the structure and morphological features of the PS and a-Si:H/PS specimens. © 2007 Elsevier B.V. All rights reserved.

In the present work, we investigate the influence of hydrocarbon (CHx) thin film coating on porous silicon (PS) by plasma enhanced chemical vapor deposition (PECVD) technique to detect CO2 gas. The fabricated CHx/PS heterojunction device shows up to one and two orders of magnitude enhancement in current under CO2 gas exposure. FTIR spectroscopy measurements reveal a remarkable structural modification of the CHx/PS device during CO2 gas exposure. Further, the enhancement of CHx related absorbance bands by a factor 6.2 for the CHx/PS specimen in comparison with PS confirm the good quality of the deposited CHx thin films. © 2007 Elsevier B.V. All rights reserved.

In the present work we investigate, the role of zinc oxide (ZnO) thin films passivating layer deposited by rf magnetron sputtering at room temperature on low (18%) and high (80%) porosity porous silicon (PS). The micro-Raman spectroscopy, Fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM) analysis have been carried out to understand the effect of ZnO films coating on PS. A systematic investigation from Raman spectroscopy suggests the formation of a good quality ZnO wurtzite structure on PS. The photoluminescence (PL) measurements on PS and ZnO coated PS shows a red, blue and UV emission bands at around ∼1.8, ∼2.78 and ∼3.2 eV. An enhancement of all PL emission bands have been achieved after ZnO films deposition on high porosity PS. © 2007 Elsevier B.V. All rights reserved.

This work refers to the fabrication of hybrid solar cells based on porous silicon (PS) filled with copper phthalocyanine (CuPc) to form GZO/CuPc-PS/Si/Al structure. We used n-type Si since photoinduced charge transfer from CuPc to Si is observed only for n-type Si. The characteristic 100% peak at 6.8°2θ from XRD confirms that the CuPc coating on PS exists in α-CuPc polymorph. The systematic increase in FWHM of XRD peak at 69.1°2θ and red-shift of LO phonon Raman spectra indicate a progressive reduction of Si nanocrystallites size with increasing etching time and the estimated size agrees well with atomic force microscopic images. The FTIR results confirm the formation of α-CuPc polymorph and it is also corroborated well with XRD and Raman results. © 2008.