Manuel J. Mendes Website

The inexorable increase of energy demand and the efficiency bottleneck of monocrystalline silicon solar cell technology is promoting the research and development of alternative photovoltaic materials. Copper-arsenic-sulfide (CAS) compounds are still rather unexplored in the literature, yet they have been regarded as promising candidates for use as p-type absorber in solar cells, owing to their broad raw material availability, suitable bandgap and high absorption coefficient. Here, a comprehensive study is presented on the structural and optoelectronic properties of CAS thin-films deposited via radio-frequency magnetron co-sputtering, using a commercial Cu target together with a Cu-As-S target with material obtained from local resources, specifically from mines in the Portuguese region of the Iberian Pyrite Belt. Raman and X-ray diffraction analysis confirm that the use of two targets results in films with pronounced stoichiometry gradients, suggesting a transition from amorphous CAS compounds to crystalline djurleite (Cu31S16), with the increasing proximity to the Cu target. Resistivity values from 4.7 mΩ·cm to 17.4 Ω·cm are obtained, being the lowest resistive films, those with pronounced sub-bandgap free-carrier absorption. The bandgap values range from 2.20 to 2.65 eV, indicating promising application as wide-bandgap semiconductors in third-generation (e.g., multi-junction) photovoltaic devices.

A fast method is presented to fabricate plasmonic light trapping structures in just ten minutes ({\textgreater}5 × faster than the present state of art), with excellent light scattering properties. The structures are composed of silver nanoparticles (Ag NPs) deposited by thermal evaporation and self-assembled using a rapid thermal annealing (RTA) system. The effect of the RTA heating rate on the NPs production reveals to be crucial to the decrease of the annealing process. The Ag NPs are integrated in thin film silicon solar cells to form a plasmonic back reflector (PBR) that causes a diffused light reflectivity in the near-infrared (600–1100 nm wavelength region). In this configuration the thicknesses of the AZO spacer/passivating layers between NPs and rear mirror, and between NPs and silicon layer, play critical roles in the near-field coupling of the reflected light towards the solar cell absorber, which is investigated in this work. The best spacer thicknesses were found to be 100 and 60 nm, respectively, for Ag NPs with preferential sizes of about 200 nm. The microcrystalline silicon ($μ$c-Si:H) solar cells deposited on such improved PBR demonstrate an overall 11{%} improvement on device efficiency, corresponding to a photocurrent of 24.4 mA/cm2 and an efficiency of 6.78{%}, against 21.79 mA/cm2 and 6.12{%}, respectively, obtained on flat structures without NPs.

{\textless}p{\textgreater}Opto-electronics on/with paper is fostering a novel generation of flexible and recyclable devices for sunlight harvesting and intelligent optical sensing.{\textless}/p{\textgreater}

The copper zinc tin sulfide (CZTS) compound is a promising candidate as an alternative absorber material for thin-film solar cells. In this study, we investigate the direct formation of Cu1.92ZnSnx(Sb1-x)S4 compounds [CZT(A)S], with x=1, 0.85, 0.70, and 0.50, via a mechanochemical synthesis (MCS) approach, starting from powders of the corresponding metals, zinc sulfide, and sulfur. The thermal stability of the CZT(A)S compounds was evaluated in detail by in situ synchrotron high-energy x-ray diffraction measurements up to 700 °C. The CZT(A)S compounds prepared via MCS revealed a sphalerite-type crystal structure with strong structural stability over the studied temperature range. The contribution of the MCS to the formation of such a structure at room temperature is analyzed in detail. Additionally, this study provides insights into the MCS of CZTS-based compounds: the possibility of a large-scale substitution of Sn by Sb and the production of single phase CZT(A)S with a Cu-poor/Zn-poor composition. A slight increase in the band gap from 1.45 to 1.49-1.51 eV was observed with the incorporation of Sb, indicating that these novel compounds can be further explored for thin-film solar cells.

© 2017 by the authors. In the present study, zinc oxide (ZnO) nanorods (NRs) with a hexagonal structure have been synthesized via a hydrothermal method assisted by microwave radiation, using specialized cardboard materials as substrates. Cardboard-type substrates are cost-efficient and robust paper-based platforms that can be integrated into several opto-electronic applications for medical diagnostics, analysis and/or quality control devices. This class of substrates also enables highly-sensitive Raman molecular detection, amiable to several different operational environments and target surfaces. The structural characterization of the ZnO NR arrays has been carried out by X-ray diffraction (XRD), scanning electron microscopy (SEM) and optical measurements. The effects of the synthesis time (5-30 min) and temperature (70-130 °C) of the ZnO NR arrays decorated with silver nanoparticles (AgNPs) have been investigated in view of their application for surface-enhanced Raman scattering (SERS) molecular detection. The size and density of the ZnO NRs, as well as those of the AgNPs, are shown to play a central role in the final SERS response. A Raman enhancement factor of 7 × 105was obtained using rhodamine 6 G (RG6) as the test analyte; a ZnO NR array was produced for only 5 min at 70 °C. This condition presents higher ZnO NR and AgNP densities, thereby increasing the total number of plasmonic "hot-spots", their volume coverage and the number of analyte molecules that are subject to enhanced sensing.

© 2014 IOP Publishing Ltd. This work reports on highly efficient surface enhanced Raman spectroscopy (SERS) constructed on low-cost, fully recyclable and highly reproducible cardboard plates, which are commonly used as disposable packaging material. The active optical component is based on plasmonic silver nanoparticle structures separated from the metal surface of the cardboard by a nanoscale dielectric gap. The SERS response of the silver (Ag) nanoparticles of various shapes and sizes were systematically investigated, and a Raman enhancement factor higher than 106for rhodamine 6G detection was achieved. The spectral matching of the plasmonic resonance for maximum Raman enhancement with the optimal local electric field enhancement produced by 60 nm-sized Ag NPs predicted by the electromagnetic simulations reinforces the outstanding results achieved. Furthermore, the nanoplasmonic SERS substrate exhibited high reproducibility and stability. The SERS signals showed that the intensity variation was less than 5{%}, and the SERS performance could be maintained for up to at least 6 months.