Manuel J. Mendes Website

The inexorable increase of energy demand and the efficiency bottleneck of monocrystalline silicon solar cell technology is promoting the research and development of alternative photovoltaic materials. Copper-arsenic-sulfide (CAS) compounds are still rather unexplored in the literature, yet they have been regarded as promising candidates for use as p-type absorber in solar cells, owing to their broad raw material availability, suitable bandgap and high absorption coefficient. Here, a comprehensive study is presented on the structural and optoelectronic properties of CAS thin-films deposited via radio-frequency magnetron co-sputtering, using a commercial Cu target together with a Cu-As-S target with material obtained from local resources, specifically from mines in the Portuguese region of the Iberian Pyrite Belt. Raman and X-ray diffraction analysis confirm that the use of two targets results in films with pronounced stoichiometry gradients, suggesting a transition from amorphous CAS compounds to crystalline djurleite (Cu31S16), with the increasing proximity to the Cu target. Resistivity values from 4.7 mΩ·cm to 17.4 Ω·cm are obtained, being the lowest resistive films, those with pronounced sub-bandgap free-carrier absorption. The bandgap values range from 2.20 to 2.65 eV, indicating promising application as wide-bandgap semiconductors in third-generation (e.g., multi-junction) photovoltaic devices.

Microstructured transparent conductive oxides (TCOs) have shown great potential as photonic electrodes in photovoltaic (PV) applications, providing both optical and electrical improvements in the solar cells’ performance due to: (1) strong light trapping effects that enhance broadband light absorption in PV material and (2) the reduced sheet resistance of the front illuminated contact. This work developed a method for the fabrication and optimization of wavelength-sized indium zinc oxide (IZO) microstructures, which were soft-patterned on flexible indium tin oxide (ITO)-coated poly(ethylene terephthalate) (PET) substrates via a simple, low-cost, versatile, and highly scalable colloidal lithography process. Using this method, the ITO-coated PET substrates patterned with IZO micro-meshes provided improved transparent electrodes endowed with strong light interaction effects—namely, a pronounced light scattering performance (diffuse transmittance up to  50%). In addition, the photonic-structured IZO mesh allowed a higher volume of TCO material in the electrode while maintaining the desired transparency, which led to a sheet resistance reduction (by  30%), thereby providing further electrical benefits due to the improvement of the contact conductance. The results reported herein pave the way for a new class of photonic transparent electrodes endowed with mechanical flexibility that offer strong potential not only as advanced front contacts for thin-film bendable solar cells but also for a much broader range of optoelectronic applications.

The optical properties of localized surface plasmon resonances (LSPR) sustained by self-assembled silver nanoparticles are of great interest for enhancing light trapping in thin film photovoltaics. First, we report on a systematic investigation of the structural and the optical properties of silver nanostructures fabricated by a solid-state dewetting process on various substrates. Our study allows to identify fabrication conditions in which circular, uniformly spaced nanoparticles are obtainable. The optimized NPs are then integrated into plasmonic back reflector (PBR) structures. Second, we demonstrate a novel procedure, involving a combination of opto-electronic spectroscopic techniques, allowing for the quantification of useful and parasitic absorption in thin photovoltaic absorber deposited on top of the PBR. We achieve a significant broadband useful absorption enhancement of 90{%} for 0.9 µm thick $μ$c-Si:H film and demonstrate that optical losses due to plasmonic scattering are insignificant below 730 nm. Finally, we present a successful implementation of a plasmonic light trapping scheme in a thin film a-Si:H solar cell. The quantum efficiency spectra of the devices show a pronounced broadband enhancement resulting in remarkably high short circuit current densities (Jsc).

Combined perovskite/crystalline-silicon four-terminal tandem solar cells promise {\textgreater}30{%} efficiencies. Here we propose all-thin-film double-junction architectures where high-bandgap perovskite top cells are coupled to ultrathin c-Si bottom cells enhanced with light trapping. A complete optoelectronic model of the devices was developed and applied to determine the optimal intermediate layers, which are paramount to maximize the cells' photocurrent. It was ascertained that by replacing the transparent conductive oxides by grid-based metallic contacts in the intermediate positions, the parasitic absorption is lowered by 30{%}. Overall, a 29.2{%} efficiency is determined for ∼2 um thick tandems composed of the optimized interlayers and improved with Lambertian light trapping.

CO2 capture and utilization (CCU) technologies are being immensely researched as means to close the anthropogenic carbon cycle. One approach known as artificial photosynthesis uses solar energy from photovoltaics (PV), carbon dioxide and water to generate hydrocarbon fuels, being methane (CH4) a preferential target due to the already in place infrastructures for its storage, distribution and consumption. Here, a model is developed to simulate a direct (1-step) solar methane production approach, which is studied in two scenarios: first, we compare it against a more conventional 2-step methane production route, and second, we apply it to address the energetic needs of concept buildings with usual space and domestic hot water heating requirements. The analysed 2-step process consists in the PV-powered synthesis of an intermediate fuel – syngas – followed by its conversion to CH4 via a Fischer–Tropsch (methanation) process. It was found that the 1-step route could be adequate to a domestic, small scale use, potentially providing energy for a single-family house, whilst the 2-step can be used in both small and large scale applications, from domestic to industrial uses. In terms of overall solar-to-CH4 energy efficiency, the 2-step method reaches 13.26{%} against the 9.18{%} reached by the 1-step method. Next, the application of the direct solar methane technology is analysed for domestic buildings, in different European locations, equipped with a combination of solar thermal collectors (STCs) and PV panels, in which the heating needs that cannot be fulfilled by the STCs are satisfied by the combustion of methane synthesized by the PV-powered electrolyzers. Various combinations of situations for a whole year were studied and it was found that this auxiliary system can produce, per m2 of PV area, in the worst case scenario 23.6 g/day (0.328 kWh/day) of methane in Stockholm, and in the best case scenario 47.4 g/day (0.658 kWh/day) in Lisbon.

A fast method is presented to fabricate plasmonic light trapping structures in just ten minutes ({\textgreater}5 × faster than the present state of art), with excellent light scattering properties. The structures are composed of silver nanoparticles (Ag NPs) deposited by thermal evaporation and self-assembled using a rapid thermal annealing (RTA) system. The effect of the RTA heating rate on the NPs production reveals to be crucial to the decrease of the annealing process. The Ag NPs are integrated in thin film silicon solar cells to form a plasmonic back reflector (PBR) that causes a diffused light reflectivity in the near-infrared (600–1100 nm wavelength region). In this configuration the thicknesses of the AZO spacer/passivating layers between NPs and rear mirror, and between NPs and silicon layer, play critical roles in the near-field coupling of the reflected light towards the solar cell absorber, which is investigated in this work. The best spacer thicknesses were found to be 100 and 60 nm, respectively, for Ag NPs with preferential sizes of about 200 nm. The microcrystalline silicon ($μ$c-Si:H) solar cells deposited on such improved PBR demonstrate an overall 11{%} improvement on device efficiency, corresponding to a photocurrent of 24.4 mA/cm2 and an efficiency of 6.78{%}, against 21.79 mA/cm2 and 6.12{%}, respectively, obtained on flat structures without NPs.

The copper zinc tin sulfide (CZTS) compound is a promising candidate as an alternative absorber material for thin-film solar cells. In this study, we investigate the direct formation of Cu1.92ZnSnx(Sb1-x)S4 compounds [CZT(A)S], with x=1, 0.85, 0.70, and 0.50, via a mechanochemical synthesis (MCS) approach, starting from powders of the corresponding metals, zinc sulfide, and sulfur. The thermal stability of the CZT(A)S compounds was evaluated in detail by in situ synchrotron high-energy x-ray diffraction measurements up to 700 °C. The CZT(A)S compounds prepared via MCS revealed a sphalerite-type crystal structure with strong structural stability over the studied temperature range. The contribution of the MCS to the formation of such a structure at room temperature is analyzed in detail. Additionally, this study provides insights into the MCS of CZTS-based compounds: the possibility of a large-scale substitution of Sn by Sb and the production of single phase CZT(A)S with a Cu-poor/Zn-poor composition. A slight increase in the band gap from 1.45 to 1.49-1.51 eV was observed with the incorporation of Sb, indicating that these novel compounds can be further explored for thin-film solar cells.

© 2017 by the authors. In the present study, zinc oxide (ZnO) nanorods (NRs) with a hexagonal structure have been synthesized via a hydrothermal method assisted by microwave radiation, using specialized cardboard materials as substrates. Cardboard-type substrates are cost-efficient and robust paper-based platforms that can be integrated into several opto-electronic applications for medical diagnostics, analysis and/or quality control devices. This class of substrates also enables highly-sensitive Raman molecular detection, amiable to several different operational environments and target surfaces. The structural characterization of the ZnO NR arrays has been carried out by X-ray diffraction (XRD), scanning electron microscopy (SEM) and optical measurements. The effects of the synthesis time (5-30 min) and temperature (70-130 °C) of the ZnO NR arrays decorated with silver nanoparticles (AgNPs) have been investigated in view of their application for surface-enhanced Raman scattering (SERS) molecular detection. The size and density of the ZnO NRs, as well as those of the AgNPs, are shown to play a central role in the final SERS response. A Raman enhancement factor of 7 × 105was obtained using rhodamine 6 G (RG6) as the test analyte; a ZnO NR array was produced for only 5 min at 70 °C. This condition presents higher ZnO NR and AgNP densities, thereby increasing the total number of plasmonic "hot-spots", their volume coverage and the number of analyte molecules that are subject to enhanced sensing.

© 2016 WILEY-VCH Verlag GmbH {&} Co. KGaA, Weinheim The post-deposition modification of ZnO-based transparent conductive oxides (TCOs) can be the key to produce thin films with optoelectronic properties similar to indium tin oxide (ITO), but at a much lower cost. Here, we present electro-optical results achieved for post-deposition annealing of Al–Zn–O (AZO), AZO:H, Ga–Zn–O:H (GZO:H), and Zn–O:H (ZNO:H) thin films deposited by RF sputtering at room temperature. These studies comprise results of thermal annealing at atmospheric pressure, vacuum, forming gas, H2and Ar atmospheres, and H2and Ar plasmas, which lead to significant enhancement of their electro-optical properties, which are correlated to morphological and structural improvements. The post-deposition annealing leads to an enhancement in resistivity above 40{%} for AZO, AZO:H, and GZO:H, reaching $\rho$ ≈ 2.6–3.5 × 10−4$Ømega$cm, while ZnO:H showed a lower improvement of 13{%}. The averaged optical transmittance in the visible region is about 89{%} for the investigated TCOs. Such results match the properties of state-of-art ITO ($\rho$ ≈ 10−4$Ømega$cm and transmittance in VIS range of 90{%}) employing much more earth-abundant materials.

© 2015 IOP Publishing Ltd. The intense light scattered from metal nanoparticles sustaining surface plasmons makes them attractive for light trapping in photovoltaic applications. However, a strong resonant response from nanoparticle ensembles can only be obtained if the particles have monodisperse physical properties. Presently, the chemical synthesis of colloidal nanoparticles is the method that produces the highest monodispersion in geometry and material quality, with the added benefits of being low-temperature, low-cost, easily scalable and of allowing control of the surface coverage of the deposited particles. In this paper, novel plasmonic back-reflector structures were developed using spherical gold colloids with appropriate dimensions for pronounced far-field scattering. The plasmonic back reflectors are incorporated in the rear contact of thin film n-i-p nanocrystalline silicon solar cells to boost their photocurrent generation via optical path length enhancement inside the silicon layer. The quantum efficiency spectra of the devices revealed a remarkable broadband enhancement, resulting from both light scattering from the metal nanoparticles and improved light incoupling caused by the hemispherical corrugations at the cells' front surface formed from the deposition of material over the spherically shaped colloids.

Metal nanoparticles and diffractive nanostructures are widely studied for enhancing light trapping efficiency in thin-film solar cells. Both have achieved high performance enhancements, but there are very few direct comparisons between the two. Also, it is difficult to accurately determine the parasitic absorption of metal nanoparticles. Here, we assess the light trapping efficiencies of both approaches in an identical absorber configuration. We use a 240 nm thick amorphous silicon slab as the absorber layer and either a quasi-random supercell diffractive nanostructure or a layer of self-assembled metal nanoparticles for light trapping. Both the plasmonic and diffractive structures strongly enhance the absorption in the red/near-infrared regime. At longer wavelengths, however, parasitic absorption becomes evident in the metal nanoparticles, which reduces the overall performance of the plasmonic approach. We have formulated a simple analytical model to assess the parasitic absorption and effective reflectivity of a plasmonic reflector and to demonstrate good agreement with the experimental data.

Plasmonic light trapping in thin film silicon solar cells is a promising route to achieve high efficiency with reduced volumes of semiconductor material. In this paper, we study the enhancement in the opto-electronic performance of thin a-Si:H solar cells due to the light scattering effects of plasmonic back reflectors (PBRs), composed of self-assembled silver nanoparticles (NPs), incorporated on the cells{&}{\#}x2019; rear contact. The optical properties of the PBRs are investigated according to the morphology of the NPs, which can be tuned by the fabrication parameters. By analyzing sets of solar cells built on distinct PBRs we show that the photocurrent enhancement achieved in the a-Si:H light trapping window (600 {&}{\#}x2013; 800 nm) stays in linear relation with the PBRs diffuse reflection. The best-performing PBRs allow a pronounced broadband photocurrent enhancement in the cells which is attributed not only to the plasmon-assisted light scattering from the NPs but also to the front surface texture originated from the conformal growth of the cell material over the particles. As a result, remarkably high values of Jsc and Voc are achieved in comparison to those previously reported in the literature for the same type of devices.