Carlos Alberto Nunes de Carvalho

This paper presents a micro power light energy harvesting system for indoor environments. Light energy is collected by amorphous silicon photovoltaic (a-Si:H PV) cells, processed by a switched capacitor (SC) voltage doubler circuit with maximum power point tracking (MPPT), and finally stored in a large capacitor. The MPPT fractional open circuit voltage (V-OC) technique is implemented by an asynchronous state machine (ASM) that creates and dynamically adjusts the clock frequency of the step-up SC circuit, matching the input impedance of the SC circuit to the maximum power point condition of the PV cells. The ASM has a separate local power supply to make it robust against load variations. In order to reduce the area occupied by the SC circuit, while maintaining an acceptable efficiency value, the SC circuit uses MOSFET capacitors with a charge sharing scheme for the bottom plate parasitic capacitors. The circuit occupies an area of 0.31 mm(2) in a 130 nm CMOS technology. The system was designed in order to work under realistic indoor light intensities. Experimental results show that the proposed system, using PV cells with an area of 14 cm(2), is capable of starting-up from a 0 V condition, with an irradiance of only 0.32 W/m(2). After starting-up, the system requires an irradiance of only 0.18 W/m(2) (18 mu W/cm(2)) to remain operating. The ASM circuit can operate correctly using a local power supply voltage of 453 mV, dissipating only 0.085 mu W. These values are, to the best of the authors' knowledge, the lowest reported in the literature. The maximum efficiency of the SC converter is 70.3 % for an input power of 48 mu W, which is comparable with reported values from circuits operating at similar power levels.

CuxS thin films, 80 nm thick, are deposited by vacuum thermal evaporation of sulfur-rich powder mixture, Cu2S:S (50:50 wt.%) with no intentional heating of the substrate. The process of deposition occurs at very low deposition rates (0.1-0.3 nm/s) to avoid the formation of Cu or S-rich films. The evolution of CuxS films surface properties (morphology/roughness) under post deposition mild annealing in air at 270 degrees C and their integration in a thin film transistor (TFT) are the main objectives of this study. Accordingly, Scanning Electron Microscopy studies show CuxS films with different surface morphologies, depending on the post deposition annealing conditions. For the shortest annealing time, the CuxS films look to be constructed of grains with large dimension at the surface (approximately 100 nm) and consequently, irregular shape. For the longest annealing time, films with a fine-grained surface are found, with some randomly distributed large particles bound to this fine-grained surface. Atomic Force Microscopy results indicate an increase of the root-mean-square roughness of CuxS surface with annealing time, from 13.6 up to 37.4 nm, for 255 and 345 s, respectively. The preliminary integration of CuxS films in a TFT bottom-gate type structure allowed the study of the feasibility and compatibility of this material with the remaining stages of a TFT fabrication as well as the determination of the p-type characteristic of the CuxS material. (c) 2013 Elsevier B.V. All rights reserved.

TiO2 films with enhanced photosensitivity were deposited on alkali free glass substrates without intentional substrate heating by pulsed DC magnetron reactive sputtering with an average thickness of about 2 mu m. Three dyes, commercial N719 and two new organic dyes were impregnated in order to control the optical spectral selectivity of such films. The type of dye used proved to dramatically influence the device's response to radiation pulses. The practical breakthrough is the use of different dyes according to the region of the electromagnetic spectrum one wants to detect. Devices with photocurrent 6 orders of magnitude higher than the dark current (from similar to 2 x 10(-12) to 2 x 10(-6) A for a 100 V bias) were fabricated with a spectral response within the visible range of the electromagnetic spectrum. In addition, this approach is likely to allow for the fabrication of hybrid photodetectors on cheap heat sensible flexible polymeric substrates. (C) 2011 Elsevier B.V. All rights reserved.

Samples of doped and undoped a-Si: H were deposited at temperatures ranging from 100 degrees C to 350 degrees C and then submitted to different dehydrogenation temperatures (from 350 degrees C to 550 degrees C) and times (from 1 h to 4 h). a-Si: H films were characterised after deposition through the measurements of specific material parameters such as: the optical gap, the conductivity at 25 degrees C, the thermal activation energy of conductivity and its hydrogen content. Hydrogen content was measured after each thermal treatment. Substrate dopant contamination from phosphorus-doped a-Si thin films was evaluated by SIMS after complete dehydrogenation and a junction depth of 0.1 mu m was obtained. Dehydrogenation results show a strong dependence of the hydrogen content of the as-deposited film on the deposition temperature. Nevertheless, the dehydrogenation temperature seems to determine the final H content in a way almost independent from the initial content in the sample. H richer films dehydrogenate faster than films with lower hydrogen concentration. (C) 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

The effect of different mild post-annealing treatments in air, at 270 degrees C, for 4-6 min, on the optical, electrical, structural and chemical properties of copper sulphide (CuxS) thin films deposited at room temperature are investigated. CuxS films, 70nm thick, are deposited on glass substrates by vacuum thermal evaporation from a Cu2S:S (50:50 wt.%) sulphur rich powder mixture. The as-deposited highly conductive crystalline CuS (covellite) films show high carrier concentration (similar to 10(22) cm(-3)), low electrical resistivity (similar to 10(-4) Omega cm) and inconclusive p-type conduction. After the mild post-annealing, these films display increasing values of resistivity (similar to 10(-3) to similar to 10(-2) Omega cm) with annealing time and exhibit conclusive p-type conduction. An increase of copper content in CuxS phases towards the semiconductive Cu2S (chalcocite) compound with annealing time is reported, due to re-evaporation of sulphur from the films. However, the latter stoichiometry was not obtained, which indicates the presence of vacancies in the Cu lattice. In the most resistive films a Cu2O phase is also observed, diminishing the amount of available copper to combine with sulphur, and therefore the highest values of optical transmittance are reached (65%). The appearance on the surface of amorphous sulphates with annealing time increase is also detected as a consequence of sulphur oxidation and replacement of sulphur with oxygen. All annealed films are copper deficient in regards to the stoichiometric Cu2S and exhibit stable p-type conductivity. (C) 2011 Elsevier B.V. All rights reserved.

Transparent, undoped semiconductive thin films of zinc oxide were deposited by radio frequency plasma enhanced reactive thermal evaporation of zinc rods in the presence of oxygen at room temperature, without any post-deposition annealing treatments. The study of the variation of rf power, in the range 5-200W, on the main properties of these films was made. A decrease of the electrical conductivity of these films with increasing rf power was observed (10(-3) to 10(-12) (Omega cm)(-1)), respectively, while the average visible transparency was kept practically constant (approximate to 80%). From this initial study, a set of bottom-gate type thin-film transistors were made using the most promising semiconductor materials. Preliminary I(V) measurements showed all transistors working, with best results obtained from zinc oxide material deposited at the lowest rf power (20 W), within the deposition conditions range which leads to semiconductive material. Such devices presented an I-on (20 V)/I-off (-5 V) ratio of 6 x 10(6) and a field-effect mobility of 0.37 cm(2)/(V s). (C) 2010 Elsevier B.V. All rights reserved.

Nowadays, among the available transparent semiconductors for device use, the great majority (if not all) have n-type conductivity. The fabrication of a transparent p-type semiconductor with good optoelectronic properties (comparable to those of n-type: InOx, ITO, ZnOx or FTO) would significantly broaden the application field of thin films. However, until now no material has yet presented all the required properties. Cu2S is a p-type narrow-band-gap material with an average optical transmittance of about 60% in the visible range for 50 nm thick films. However, due to its high conductivity at room temperature, 10 nm in thickness seems to be appropriate for device use. Cu2S thin films with 10 nm in thickness have an optical visible transmittance of about 85% rendering them as very good candidates for transparent p-type semiconductors. In this work CuxS thin films were deposited on alkali-free (AF) glass by thermal evaporation. The objective was not only the determination of its optoelectronic properties but also the feasibility of an active layer in a p-type thin film transistor. In our CuxS thin films, p-type high conductivity with a total visible transmittance of about 50% have been achieved. (C) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Conductive and transparent undoped thin films of indium oxide (InOx), 120 nm average thick, were deposited by radio frequency plasma enhanced reactive thermal evaporation (rf-PERTE) of indium in the presence of oxygen at room temperature. Several substrates were used in order to study their influence on the main properties of these films: alkali free (AF) glass, fused silica, crystalline silicon and polyethylene terephthalate (PET). Surface morphology of the InOx films as a function of the substrates was observed by SEM and showed that the undoped InOx films obtained are nano-structured. For the c-Si substrate, InOx films with increased grain size are obtained, induced by the crystalline substrate. Films deposited on fused silica and AF glass substrates show a nano-grainy surface with similar surface morphologies. The InOx films deposited on AF glass show the highest values of both: electrical conductivity of about 1100 (Omega cm)(-1) and visible transmittance of 85%. The substrate has a greater influence on the surface morphology of the films when a polymer (PET) is used. InOx films deposited on PET show a decrease in the electrical conductivity (90 (Omega cm)(-1)) and a slight decrease in the average visible transmittance (78%).