Rodrigo Martins

We present a set of high-efficiency optical sensors for the spectral range from 0.25 to 1.1 μm based on metal oxide-semiconductor heterostructures using different substrates: GaP, GaSe, AlxGa1-xAs, GaAs and Si. A set of several transparent conductive metal oxide films such as indium, tin and zinc oxides fabricated by the spray pyrolysis method and its doping procedure has been investigated. The results show that heavily doped indium and tin oxide films are preferable as the active transparent conductive electrode in heterojunction surface-barrier structures. The fabricated sensors exhibit several features such as process simplicity, high quantum efficiency, uniformity of sensitivity over the active area and a high response speed. Such sensors can be used for precision measurements in different scientific and technical applications.

We have developed new types of functional and smart optical silicon sensors, based on ITO/multichannel insulator/silicon structures, which are able to execute electronic functions such as amplifying the photocurrent (without avalanche multiplication), transforming the input optical signal into a radio frequency output signal and transforming the analogue input optical signal to a digital output form, without external active electronic components. These new functional optical sensors allow a substantial simplification of the registration of optical signals as well as of the electronic scheme to be used. © 1998 Elsevier Science S.A. All rights reserved.

We have developed new types of functional and smart optical silicon sensors, based on ITO/multichannel insulator/silicon structures, which are able to execute electronic functions such as amplifying the photocurrent (without avalanche multiplication), transforming the input optical signal into a radio frequency output signal and transforming the analogue input optical signal to a digital output form, without external active electronic components. These new functional optical sensors allow as substantial simplification of the registration of optical signals as well as of the electronic scheme to be used.

We have developed a linear thin film position-sensitive detector with 128 elements, based on p.i.n. a-Si:H devices. The incorporation of this sensor into an optical inspection camera makes possible the acquisition of three-dimensional information of an object, using laser triangulation methods. The main advantages of this system, when compared with the conventional charge-coupled devices, are the low complexity of hardware and software used, and that the information can be continuously processed (analogic detection). In this paper, we present the most significant characteristics of the singular one-dimensional thin film position-sensitive detectors that form part of the linear array with 128 sensors. © 1998 Elsevier Science S.A.

Pd-metal/insulator/semiconductor based on hydrogenated amorphous silicon were produced by plasma enhanced chemical vapour deposition with two different oxidised surfaces: thermal in ambient air and chemical with hydrogen peroxide. The diode characteristics have been investigated using dark and light current as f(v) measurements in the temperature range from 300 K to 380 K, from which it was possible to infer the electron barrier height. The data obtained show that the incorporation of a thin insulator layer between the semiconductor and the metal improves the performances of the devices by preventing the formation of suicides at the interface. Apart from that we also show that the MIS structures with the thermal oxide presents 'better' performances than the ones with the chemical oxide due to the type of interface states and of the oxide charges associated with the interface between the insulator and the semiconductor. © 1998 Elsevier Science B.V. All rights reserved.

In this paper, we present results of the role of laser beam energy and shot density on the electro-optical and structural properties of undoped and doped recrystallized amorphous silicon thin films, generated by pulsed Nd-YAG laser (λ = 532 nm). The data reveal that the structure and electrical characteristics of the recrystallized thin films are mainly dependent on the energy and shot density of the laser beam, while the morphology of the obtained films are mainly governed by the number of shots used. The data also show that the electrical conductivity of undoped and doped recrystallized films can be varied up to 6 orders of magnitude, by the proper choice of the recrystallization conditions. Doped samples with conductivities in the amorphous states in the range of 10-5 Ω-1 cm-1 present, after recrystallization, conductivities of about 300 Ω-1 cm-1. The SEM micro-chemical analysis also shows that the obtained crystalline grains are constituted by pure silicon. © 1998 Elsevier Science S.A.

The present paper describes the properties of a photochemical sensor based on amorphous silicon MIS (Metal-Insulator-Semiconductor) diodes. The structure of the sensors used in this work are based on glass/Cr/a-SiH(n +)/a-Si:H(i)SiOx/Pd, where the amorphous silicon layers have been deposited by conventional plasma r.f. techniques. The proposed photochemical sensors present a 2-3 orders of magnitude change in the saturation current and a decrease of up to 40% on the open circuit voltage when in the presence of 400 ppm of hydrogen. The overall performance of these sensors, associated with the low cost fabrication technology, suggests that, in the near future, it will be possible to use them in several industrial applications. © 1998 Elsevier Science Ltd. All rights reserved.

The increasing demand in automation processes in finishing techniques also calls for automatic measurement and inspection methods. These methods ought to be installed as close as possible to the production process and they ought to measure the values needed in a safe and fast way, without disturbing the process itself. Simultaneously they should be free of wear and insensitive against mechanical perturbations. This approach can be reached by proper combination of the laser triangulation technique with an array of linear position sensitive detectors, able to supply information about the surface finishing of an object. This is the aim of this paper that envisages to present experimental results of the performances exhibited by such an array constituting 128 elements. The analogue information supplied by this array is processed by an analogue/digital converter, directly coupled to the array and whose information is computer processed, concerning the recognition of patterns and the processing of information collected over the object to be inspected. © 1999 Elsevier Science S.A. All rights reserved.

Undoped and doped (indium and aluminium) zinc oxide (ZnO) thin films have been prepared by spray pyrolysis, and the effect of the doping and annealing atmosphere on the electrical, optical and structural properties of the produced films has been investigated. The deposited films have a high resistivity. Annealing the films in an argon atmosphere or under vacuum leads to a substantial reduction of the electrical resistivity of the films and to an increase on the degree of cristallinity of the deposited material. The most pronounced changes were observed in the films annealed in Argon. The results also indicate that doping highly influences the electrical and structural properties of the films, which is more pronounced in the films doped with Indium. © 1998 Elsevier Science Ltd. All rights reserved.

This work deals with the role of hydrogen dilution and filament temperature on the morphology, structure and electrical properties of nanocrystalline boron doped silicon carbide thin films produced by hot-wire technique. The structural and morphological data obtained by XRD, SEM and micro-Raman show that for filament temperatures and hydrogen dilutions above 2100 °C and 90%, respectively, the surface morphology of the films is granular with a needle shape, while for lower filament temperatures and hydrogen dilutions the surface morphology gets honeycomb like. The SIMS analysis reveals that films produced with filament temperatures of about 2200 °C and hydrogen dilution of 99% present a higher hydrogen and carbon incorporation than the films produced at lower temperatures and hydrogen dilutions. These results agree with the electrical and optical characteristics recorded that show that the films produced exhibit optical gaps in the range from 1.8 to 2 eV and transverse conductivities ranging from 10-1 S/cm to 10-3 S/cm, consistent with the degree of films crystallinity and carbon incorporation recorded.

In this work we present data concerning the structure, composition and electro-optical performances of nanocrystalline silicon carbide doped films produced at the different filament temperatures and hydrogen dilution ratios. The XRD spectra reveal the presence of the typical Si peaks ascribed to (111) (220) and (311) diffraction planes, where no traces of the carbon peaks were found. The average grain sizes ranges from 10 nm to 30 nm, depending on the temperature of filament and hydrogen dilution used. We observed an enhancement of the peak ascribed to the (220) plane when high H dilution rates are used, meaning that the film starts being textured. The infrared data reveal the typical silicon carbide modes and a hydrogen content that varies from 3% to 1%, with the increase of the filament temperature. Besides that, the IR spectra show the typical SiO2 and SiO modes, associated to the oxide species that are mainly incorporated in the surface of the films and can be removed by proper wet etching. The planar conductivity is enhanced as the temperature of the filament is increased, being the highest conductivity achieved in the range of 0.2 (Ωcm)-1 and almost non activated. © 1998 Elsevier Science Ltd. All rights reserved.

The aim of this paper is to present results on a new soldering process based on the low-temperature solidification of intermetallic phases from the system Cu-Sn-Cu which can be employed to form a heat-resistant die-attach as well as signal and power electric contacts. Because of the total transformation into intermetallic phase, the working temperature of the bond formed is several hundred degrees Celsius higher than the process temperature (around 250°C). This process leads to a homologous temperature T/Tm of about 0.3 compared to 0.7 in the case of soft SnAg solder alloy. Therefore a better reliability of the proposed bonding process is achievable. Results of the match of the predicted volume fraction of the intermetallic forms and the experimentally measured contact volume would be also discussed, for contacts formed in power diodes.

This work refers to the main electro-optical characteristics exhibited by large area indium tin oxide films (300 × 400 mm) produced by r.f. magnetron sputtering under different oxygen concentrations and deposition pressures. Besides that, the ageing effect on the electro-optical characteristics of the films produced was also analyzed. The results achieved show that the film transparency and conductivity were highly improved (more than four orders of magnitude) by first annealing them in air at 470°C, followed by a reannealed stage under vacuum, in a hydrogen atmosphere, at 350°C. The ageing tests show that film degradation occurs when the films are produced at oxygen concentrations above 10% and/or at deposition pressures above 1.2 × 10-2 mbar. © 1999 Elsevier Science S.A. All rights reserved.

This work reports on the performances of undoped and doped amorphous/nanocrystalline silicon films grown by hot wire plasma assisted technique. The structure (including the presence of several nanoparticles with sizes ranging from 5 nm to 50 nm), composition (oxygen and hydrogen content) and transport properties of the films are highly dependent on the temperature of the filament and on the hydrogen dilution. The undoped films grown under low r.f. power (≈4mWcm-2) and filament temperatures around 1850 K present dark conductivities below 10-10 Scm-1, optical gaps of about 1.6 eV and photosensitivities above 105, (under AM 1.5 light intensities), with almost no traces of oxygen content. For the n- and the p-doped silicon films also fabricated under the same conditions the conductivities obtained are of about 10-2Scm-1 and 10-5Scm-1, respectively. © 1998 Elsevier Science Ltd. All rights reserved.

This work reports on the performances of undoped and n doped amorphous/nano-crystalline silicon films grown by hot wire plasma assisted technique. The film's structure (including the presence of several nanoparticles with sizes ranging from 5 nm to 50 nm), the composition (oxygen and hydrogen content) and the transport properties are highly dependent on the filament temperature and on the hydrogen dilution. The undoped films grown under low r.f. power (≈4 mWcm-2) and with filament temperatures around 1850 °K have dark conductivities below 10-10 Scm-1, optical gaps of about 1.5 eV and photo-sensitivities above 105, (under AM1.5), with almost no traces of oxygen content. N-doped silicon films were also fabricated under the same conditions which attained conductivities of about 10-2 Scm-1.

The effect of doping and annealing atmosphere on the performances of zinc oxide thin films prepared by spray pyrolysis have been studied. The results show that the way doping influences the electrical and structural properties depends also on the characteristics of the doping element. Annealing the as-deposited films in an inert atmosphere leads to a substantial reduction in the resistivity of the films deposited and to an increase on the degree of film's crystallinity. © 1999 Elsevier Science S.A. All rights reserved.

The aim of this work is to present an analytical model able to interpret the role of the thin collecting resistive layer on the static performances exhibited by 2D amorphous silicon hydrogenated pin thin film position sensitive detectors. In addition, experimental results concerning the device linearity and spatial resolution are presented and checked against the predicted values of the analytical model proposed.

Nanocrystalline p-doped silicon films were deposited at low substrate temperatures (around 200°C) in a hot wire reactor. In this paper we present the results on the role of the hydrogen dilution and filament temperature on the film's structure, composition, morphology and transport properties. The film's structure changes from honeycomb-like to a granular needle shape as the filament temperature changes from about 2000°C and hydrogen dilution 87%, to values above 2100°C and hydrogen dilution 90%, respectively. The nanocrystalline silicon-based films produced have optical gaps varying from 1.6 to 1.95 eV, with conductivities up to 0.2 S cm-1 and grain sizes (obtained by X-ray diffraction) in the range of 10-30 nm. © 1999 Elsevier Science B.V. All rights reserved.

The aim of this work is to present an analytical model which can to interpret the role of the collecting resistive layer on the static performances exhibited by 2D amorphous silicon hydrogenated p-i-n thin film position sensitive detectors. In addition, experimental results concerning the device linearity and spatial resolution are presented and checked against the predicted values of the analytical model proposed. © 1999 Elsevier Science S.A. All rights reserved.

This paper is concerned with the modelling and simulation of amorphous and microcrystalline silicon optoelectronic devices. The physical model and its mathematical formulation are extensively described. Its numerical reduction is also discussed together with the presentation of a computer program dedicated to the simulation of the electrical behaviour of such devices. This computer program, called ASCA (Amorphous Silicon Solar Cells Analysis), is capable of simulating, on one- and two-dimensional domains, the internal electrical behaviour of multi-layer structures, homojunctions and heterojunctions under simple or complex spectra illumination and externally applied biases. The applications of the simulator presented in this work are the analysis of μc/a-Si:H p-i-n photovoltaic cell in thermal equilibrium and illuminated by monochromatic light and the AMI.5 solar spectrum, with and without polarisation. We also study the appearance within the device of lateral components of the electric field and current density vectors when the illumination is not uniform. © 1999 IMACS/Elsevier Science B.V. All rights reserved.

In previous papers the mean excess chemical potential, μ1(E), in ternary systems of the type I sulphate + II sulphate + H2O, at 25°C was determined. Results obtained for systems with CuSO4(I), and ZnSO4(I) respectively, pointed out an obvious disparity between their behaviours. They show the existence of some important association phenomena partially accounting for the substantial deviations from ideal behaviour. The ternary sulphate systems (CuSO4 + Me(I,II)SO4 + H2O; ZnSO4 + Me(I,II)SO4 + H2O) studied were characterized against the binaries of the same ionic strength, experimental data being obtained using both e.m.f. and spectrophotometric methods. Deviations from the ideal behaviour were discussed in terms of thermodynamic excess functions and association constants. A comparative study between the results obtained with the two above mentioned methods is presented. In previous papers the mean excess chemical potential, μ1 E, in ternary systems of the type I sulphate+II sulphate+H2O, at 25 °C was determined. Results obtained for systems with CuSO4(I), and ZnSO4(I) respectively, pointed out an obvious disparity between their behaviours. They show the existence of some important association phenomena partially accounting for the substantial deviations from ideal behaviour. The ternary sulphate systems (CuSO4+MeI, IISO4+H2O; ZnSO4+MeI, IISO4+H2O) studied were characterized against the binaries of the same ionic strength, experimental data being obtained using both e.m.f. and spectrophotometric methods. Deviations from the ideal behaviour were discussed in terms of thermodynamic excess functions and association constants. A comparative study between the results obtained with the two above mentioned methods is presented.

Microcrystalline silicon is a two-phase material. Its composition can be interpreted as a series of grains of crystalline silicon imbedded in an amorphous silicon tissue, with a high concentration of dangling bonds in the transition regions. In this paper, results for the transport properties of a μc-Si:H p-i-n junction obtained by means of two-dimensional numerical simulation are reported. The role played by the boundary regions between the crystalline grains and the amorphous matrix is taken into account and these regions are treated similar to a heterojunction interface. The device is analyzed under AM1.5 illumination and the paper outlines the influence of the local electric field at the grain boundary transition regions on the internal electric configuration of the device and on the transport mechanism within the μc-Si:H intrinsic layer.

Microcrystalline silicon is a two-phase material. Its composition can be interpreted as grains of crystalline silicon imbedded in an amorphous silicon tissue, with a high concentration of danglind bonds in the transition regions. In this paper, results obtained by means of numerical simulations about the transport properties of a μc-Si:H p-i-n junction are reported. The role played by the boundary regions between the crystalline grains and the amorphous matrix is taken in account, and these regions are treated similarly to a heterojunction interface. The influence of the local electric field at the grains boundary transition regions on the internal electric configuration of the device is outlined under illumination and applied external bias. © 1999 Elsevier Science S.A. All rights reserved.

In order to understand the kinetics of formation of interface/surface states and its correlation on the final device performance, a preliminary study was performed on MIS structures, before and after surface oxidation/passivation, using different oxidation techniques and oxides: thermal (in air), chemical (in H2O2) and oxygen plasma. The devices used in this work are based on a glass/Cr/a-Si:H(n+)/a-Si:H(i)/SiOx/Pd structures, where the amorphous silicon intrinsic layer (i a-Si:H) with a photosensitivity of 107 was deposited by a modified plasma enhanced chemical vapour deposition (PECVD) triode system. The electrical properties of a-Si:H MIS structures were investigated by measuring their diode current-voltage characteristics in the dark and under illumination as well as the spectral response, as a function of the various oxidation techniques. Infrared spectroscopy and spectroscopic ellipsometry were used as a complementary tool to characterise the oxidised surface.

Large area thin film position sensitive detectors based on amorphous silicon technology have been prepared on polyimide substrates using the conventional plasma-enhanced chemical vapour deposition. The sensors have been characterized by spectral response, light intensity dependence and linearity measurements in a bent state in order to evaluate the properties in real working conditions. The obtained one-dimensional (1D) position sensors with 10 mm width and 20 mm length present a non-linearity of ±1% which are comparable to the ones produced on glass substrates.