Rodrigo Martins

Hall effect measurements are one of the most powerful techniques for obtaining information about the conduction mechanism in polycrystalline semiconductor materials, which is the basis for understanding semiconductor gas sensors. In order to investigate the correlation between the microscopic characteristics and the macroscopic performances exhibited by undoped tin oxide gas sensors deposited by spray pyrolysis, Hall effect measurements were performed at different temperatures, from room temperature up to 500 K, and in the presence of two different atmospheres, air and methane. From these measurements, it was possible to infer the potential barrier and its dependence with the used atmosphere. The obtained results were analysed in terms of the oxygen mechanism at grain boundaries on the basis of the grain boundary-trapping model. In the presence of methane gas, the electrical resistivity decreases due to the lowering of the inter-grain boundary barrier height.

The purpose of this work is to present in-depth electrical characterization on transparent TFTs, using zinc oxide produced at room temperature as the semiconductor material. Some of the studied aspects were the relation between the output conductance in the post-pinch-off regime and width-to-length ratios, the gate leakage current, the semiconductor/insulator interface traps density and its relation with threshold voltage. The main point of the analysis was focused on channel mobility. Values extracted using different methodologies, like effective, saturation and average mobility, are presented and discussed regarding their significance and validity. The evolution of the different types of mobility with the applied gate voltage was investigated and the obtained results are somehow in disagreement with the typical behavior found on classical silicon based MOSFETs, which is mainly attributed to the completely different structures of the semiconductor materials used in the two situations: while in MOSFETS we have monocrystalline silicon, our transparent TFTs use poly/nanocrystalline zinc oxide with grain sizes of about 10 nm.

Electrical dark conductivity (σd) and surface composition of undoped and doped a-Si:H thin films have been investigated, using coplanar I−V as a function of temperature and Auger electron spectroscopy (AES). The films were prepared by rf glow discharge deposition on standard soda-lime glass and on alkali-free glass substrates. Comparing these two sets of substrates for undoped films, we find that σd of the films deposited on soda-lime glass substrates at room temperature is higher by more than two orders of magnitude, their activation energy is lower by about a factor of 3, and their photosensitivity (σph/σd) is lower by two orders of magnitude than that of the films deposited on alkali-free glass substrates. We suggest that Na ions, leached from the glass into the a-Si:H overlayer play a significant role in determining the film conductivity by creating electrically active donorlike states. This conclusion is supported by similar measurements on p- and n-type a-Si:H films on the same substrates and by AES results. Films of a-Si:H, grown on thin a-Si:C:H interlayers on soda-lime glass, showed very low Na concentrations and low dark conductivities as found by AES and electrical measurements, respectively. The role of the a-Si:C:H interlayers as diffusion barriers is discussed. © 1989, American Vacuum Society. All rights reserved.

The reduction of aCu2O layer on copper by exposure toTMAduring the atomic layer deposition of Al2O3 has recently been reported. (Gharachorlou et al 2015 ACS Appl. Mater. Interfaces 7 16428-16439). The study presented here analyzes a similar process, leading to the reduction of a homogeneous Cu2O thin film, which allows for additional observations. Angle-resolved in situ X-ray photoelectron spectroscopy confirms the localization of metallic copper at the interface. The evaluation of binding energy shifts reveals the formation of aCu2O/Cu Schottky barrier, which gives rise to Fermi level pinning in Cu2O. An initial enhancement of the ALD growth per cycle (GPC) is only observed for bulk Cu2O samples and is thus related to lattice oxygen, originating from regions lying deeper than just the first few layers of the surface. The oxygen out-take from the substrate is limited to the first few cycles, which is found to be due to a saturated copper reduction, rather than the oxygen diffusion barrier of Al2O3. © 2016 IOP Publishing Ltd.

This work reports on the fabrication process and performances presented by metal insulator semiconductor (MIS) linear position sensitive detectors (PSD) with an active length of 6 cm. The use of long sensitive areas allows the PSD to achieve higher resolution without the need of a highly accurate light spot integration mechanism. The PSD is built in a multilayered structure consisting of Cr/a-Si:H (n+ doped)/a-Si:H (intrinsic)/SiOx (passivation layer)/Au, where the active a-Si:H layers were deposited by a modified triode plasma enhanced chemical vapour deposition (MTPECVD), which allows the deposition of highly electronic grade material with a low (≈ × 1015 cm-3) defect density inferred by CPM. The sensor linearity and sensitivity shows dependence on the sensor width to length ratio and on the value of load resistance. Sensitivities of more than 30 mV/cm were achieved with linearity near 99%. Besides that, this type of MIS structure allows an improved spectral response near the UV region and has the maximum response at 540 nm. © 2004 Published by Elsevier B.V.

In this paper, we present the preliminary results concerning the deposition of highly transparent and conductive gallium-doped zinc oxide (GZO) deposited on transparent flexible substrate based on cellulose derivatives. Prior to the deposition of the GZO film, the surface of the polymer have been coated with a thin silicon dioxide (SiO2) layer deposited by thermal evaporation assisted by an electron gun. By doing this surface treatment, we succeeded in depositing highly conductive and transparent GZO with an electrical resistivity of 2.0 × 10-3 Ω cm and an average optical transmittance in the visible part of the spectrum (400-700 nm) of 70% by r.f. magnetron sputtering at room temperature. Besides the optoelectronic properties, the films are mechanically stable with a polycrystalline structure with a strong preferred (002) orientation, parallel to the substrate. © 2003 Elsevier B.V. All rights reserved.

The surfaces of cordierite and glass particles were modified by coating them with an alumina precursor using a precipitation process in the presence of urea. Scanning electron microscopy (SEM), high-resolution transmission electron microscopy, X-ray diffraction, electrophoresis, and rheological measurements were used to characterize the coated powders. SEM and transmission electron microscopy morphologies of the coated powders revealed that amorphous and homogeneous coatings have been formed around the particles. The morphology of the coated powders showed a coiled wormlike surface. The coating Al2O3 layer dominated the surface properties of the coated glass and cordierite powders. The influence of the coating layer on the processing ability of cordierite-based glass-ceramics substrates by tape casting was studied in aqueous media. It could be concluded that the coating of the powders facilitates the processing and yields green and sintered tapes with denser, more homogeneous microstructures compared with the uncoated powders.

This paper deals with a new model and structure able to tailor defects in pin devices. The model assumes the usual density of states profile, including donor and acceptor like states inside the mobility gap and has the capability to simulate the transient and steady state device behavior. The new structure is based in two interfacial defectous layers, located at the junctions, acting as "gettering" centers to tailor the defects. The role of the interlayer and its thickness on device performances will be also discussed. © 1993.

This paper focuses on the engineering procedures governing the synthesis of tungsten oxide nanocrystals and the formulation of printable dispersions for electrochromic applications. By that means, we aim to stress the relevancy of a proper design strategy that results in improved physicochemical properties of nanoparticle loaded inks. In the present study inkjet printable nanostructured tungsten oxide particles were successfully synthesized via hydrothermal processes using pure or acidified aqueous sol-gel precursors. Based on the proposed scheme, the structure and morphology of the nanoparticles were tailored to ensure the desired printability and electrochromic performance. The developed nanomaterials with specified structures effectively improved the electrochemical response of printed films, resulting in 2.5 times higher optical modulation and 2 times faster coloration time when compared with pure amorphous films. © The Royal Society of Chemistry 2015.

In previous papers the mean excess chemical potential, μ1(E), in ternary systems of the type I sulphate + II sulphate + H2O, at 25°C was determined. Results obtained for systems with CuSO4(I), and ZnSO4(I) respectively, pointed out an obvious disparity between their behaviours. They show the existence of some important association phenomena partially accounting for the substantial deviations from ideal behaviour. The ternary sulphate systems (CuSO4 + Me(I,II)SO4 + H2O; ZnSO4 + Me(I,II)SO4 + H2O) studied were characterized against the binaries of the same ionic strength, experimental data being obtained using both e.m.f. and spectrophotometric methods. Deviations from the ideal behaviour were discussed in terms of thermodynamic excess functions and association constants. A comparative study between the results obtained with the two above mentioned methods is presented. In previous papers the mean excess chemical potential, μ1 E, in ternary systems of the type I sulphate+II sulphate+H2O, at 25 °C was determined. Results obtained for systems with CuSO4(I), and ZnSO4(I) respectively, pointed out an obvious disparity between their behaviours. They show the existence of some important association phenomena partially accounting for the substantial deviations from ideal behaviour. The ternary sulphate systems (CuSO4+MeI, IISO4+H2O; ZnSO4+MeI, IISO4+H2O) studied were characterized against the binaries of the same ionic strength, experimental data being obtained using both e.m.f. and spectrophotometric methods. Deviations from the ideal behaviour were discussed in terms of thermodynamic excess functions and association constants. A comparative study between the results obtained with the two above mentioned methods is presented.

This work reports the structural, optical, electrical and thermoelectric properties of vanadium pentoxide (V2O5) thin films deposited at room temperature by thermal evaporation on Corning glass substrates. A post-deposition thermal treatment up to 973 K under atmospheric conditions induces the crystallization of the as-deposited amorphous films with an orthorhombic V2O5 phase with grain sizes around 26 nm. As the annealing temperature rises up to 773 K the electrical conductivity increases. The films exhibit thermoelectric properties with a maximum Seebeck coefficient of -218 μV/K and electrical conductivity of 5.5 (Ω m) -1. All the films show NIR-Vis optical transmittance above 60% and optical band gap of 2.8 eV. © 2013 Elsevier B.V. All rights reserved.

The present work proposes the development of a bio-battery composed by an ultrathin monolithic structure of an electrospun cellulose acetate membrane, over which was deposited metallic thin film electrodes by thermal evaporation on both surfaces. The electrochemical characterization of the bio-batteries was performed under simulated body fluids like sweat and blood plasma [salt solution - 0.9% (w/w) NaCl]. Reversible electrochemical reactions were detected through the cellulose acetate structure. Thus, a stable electrochemical behavior was achieved for a bio-battery with silver and aluminum thin films as electrodes. This device exhibits the ability to supply a power density higher than 3μWcm-2.Finally, a bio-battery prototype was tested on a sweated skin, demonstrating the potential of applicability of this bio-device as a micropower source. © 2010 Elsevier B.V.

The application of hydrogenated amorphous silicon (a-Si:H) to optoelectronic devices are now well established as a viable low cost technology and is presently receiving much interest. Taking advantage of the properties of a-Si:H based devices, single and dual axis large area (up to 80×80 mm 2) thin film position sensitive detectors (TFPSD) based on a-Si:H p-i-n diodes have been developed, produced by plasma enhanced chemical vapor deposition. In this study, the main optoelectronic properties presented by the TFPSD as well as their behavior under operation conditions, concerning its linearity and signal to noise ratio, are reported. © 1994 American Institute of Physics.

The performances of silicon carbide position sensitive detectors in relation to position color selection applications were presented. The devices were deposited on glass substrates coated with a transparent conductive oxide layer based on indium tin oxide film (ITO). On top of the ITP layer a pin structure produced by plasma enhanced chemical vapor deposition technique was deposited. The set of data achieved indicated that the undoped silicon carbide layers presented a low density of states, which explained high dark conductivity values obtained and the type of performances recorded on the PSD devices produced.

The present development of non-wafer-based photovoltaics (PV) allows supporting thin film solar cells on a wide variety of low-cost recyclable and flexible substrates such as paper, thereby extending PV to a broad range of consumer-oriented disposable applications where autonomous energy harvesting is a bottleneck issue. However, their fibrous structure makes it challenging to fabricate good-performing inorganic PV devices on such substrates. The advances presented here demonstrate the viability of fabricating thin film silicon PV cells on paper coated with a hydrophilic mesoporous layer. Such layer can not only withstand the cells production temperature (150 C), but also provide adequate paper sealing and surface finishing for the cell's layers deposition. The substances released from the paper substrate are continuously monitored during the cell deposition by mass spectrometry, which allows adapting the procedures to mitigate any contamination from the substrate. In this way, a proof-of-concept solar cell with 3.4% cell efficiency (41% fill factor, 0.82 V open-circuit voltage and 10.2 mA cm-2 short-circuit current density) is attained, opening the door to the use of paper as a reliable substrate to fabricate inorganic PV cells for a plethora of indoor applications with tremendous impact in multi-sectorial fields such as food, pharmacy and security. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The present development of non-wafer-based photovoltaics (PV) allows supporting thin film solar cells on a wide variety of low-cost recyclable and flexible substrates such as paper, thereby extending PV to a broad range of consumer-oriented disposable applications where autonomous energy harvesting is a bottleneck issue. However, their fibrous structure makes it challenging to fabricate good-performing inorganic PV devices on such substrates. The advances presented here demonstrate the viability of fabricating thin film silicon PV cells on paper coated with a hydrophilic mesoporous layer. Such layer can not only withstand the cells production temperature (150 °C), but also provide adequate paper sealing and surface finishing for the cell's layers deposition. The substances released from the paper substrate are continuously monitored during the cell deposition by mass spectrometry, which allows adapting the procedures to mitigate any contamination from the substrate. In this way, a proof-of-concept solar cell with 3.4% cell efficiency (41% fill factor, 0.82 V open-circuit voltage and 10.2 mA cm-2 short-circuit current density) is attained, opening the door to the use of paper as a reliable substrate to fabricate inorganic PV cells for a plethora of indoor applications with tremendous impact in multi-sectorial fields such as food, pharmacy and security. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

We have developed a linear thin film position-sensitive detector with 128 elements, based on p.i.n. a-Si:H devices. The incorporation of this sensor into an optical inspection camera makes possible the acquisition of three-dimensional information of an object, using laser triangulation methods. The main advantages of this system, when compared with the conventional charge-coupled devices, are the low complexity of hardware and software used, and that the information can be continuously processed (analogic detection). In this paper, we present the most significant characteristics of the singular one-dimensional thin film position-sensitive detectors that form part of the linear array with 128 sensors. © 1998 Elsevier Science S.A.

Pd-metal/insulator/semiconductor based on hydrogenated amorphous silicon were produced by plasma enhanced chemical vapour deposition with two different oxidised surfaces: thermal in ambient air and chemical with hydrogen peroxide. The diode characteristics have been investigated using dark and light current as f(v) measurements in the temperature range from 300 K to 380 K, from which it was possible to infer the electron barrier height. The data obtained show that the incorporation of a thin insulator layer between the semiconductor and the metal improves the performances of the devices by preventing the formation of suicides at the interface. Apart from that we also show that the MIS structures with the thermal oxide presents 'better' performances than the ones with the chemical oxide due to the type of interface states and of the oxide charges associated with the interface between the insulator and the semiconductor. © 1998 Elsevier Science B.V. All rights reserved.

The reduction of the In2O3 caused by the deposition of μc-Si:C:H by means of plasma-enhanced CVD, is considerably diminished if a thin (50 Å) silicon monoxide layer is applied as a diffusion barrier. The amount of reduced indium diminishes by a factor three while the amount of silicon oxide is also less, although SiO was added on purpose. First results on an amorphous silicon In2O3/pi junction show that the SiO layer benefits the opto-electrical characteristics. © 1991.

Thin-film transistors (TFTs) were fabricated using a 20-nm-thick indium molybdenum oxide (IMO) semiconductor layer at room temperature. The grazing incidence X-ray diffraction patterns confirmed that the deposited films are amorphous. The average transmittance (400-2500 nm) and the optical band gap are ∼88% and 3.95 eV, respectively. The TFTs fabricated on glass substrates showed a saturation mobility of 4.0 cm2/Vċ s with an I ON/IOFF ratio of 2 × 103 and a threshold voltage of-1.1 V, which are encouraging preliminary results in order to develop IMO as high-performance semiconductor layer. © 2011 IEEE.

Copper oxide (Cu2 O) thin films were used to produce bottom gate p-type transparent thin-film transistors (TFTs). Cu2 O was deposited by reactive rf magnetron sputtering at room temperature and the films exhibit a polycrystalline structure with a strongest orientation along (111) plane. The TFTs exhibit improved electrical performance such as a field-effect mobility of 3.9 cm2 /V s and an on/off ratio of 2× 102. © 2010 American Institute of Physics.

Here we present for the first time a TiO2/Cu2O all-oxide heterojunction solar cell entirely produced by spray pyrolysis onto fluorine doped tin oxide (FTO) covered glass substrates, using silver as a back contact. A combinatorial approach was chosen to investigate the impact of the TiO2 window layer and the Cu2O light absorber thicknesses. We observe an open circuit voltage up to 350 mV and a short circuit current density which is strongly dependent of the Cu2O thickness, reaching a maximum of  0.4 mA/cm2. Optical investigation reveals that a thickness of 300 nm spray pyrolysis deposited Cu2O is sufficient to absorb most photons with an energy above the symmetry allowed optical transition of 2.5 eV, indicating that the low current densities are caused by strong recombination in the absorber that consists of small Cu2O grains. © 2014 Elsevier Ltd. All rights reserved.

This work analyzes the role of processing parameters on the electrical performance of GIZO (Ga2 O3: In2 O3:ZnO) films and thin-film transistors (TFTs). Parameters such as oxygen partial pressure, deposition pressure, target composition, thickness, and annealing temperature are studied. Generally, better devices are obtained when low oxygen partial pressure is used. This is related to the damage induced by oxygen ion bombardment and very high film's resistivity when higher oxygen partial pressures are used. Low deposition pressures and targets with richer indium compositions led to films with high carrier concentration, resulting in transistors with field-effect mobility as high as ∼80 cm2 Vs but poor channel conductivity modulation, becoming ineffective as switching devices. Nevertheless, it is demonstrated that reducing the GIZO thickness from 40 to 10 nm greatly enhances the switching behavior of those devices, due to the lower absolute number of free carriers and hence to their easier depletion. Annealing also proves to be crucial to control device performance, significantly modifying GIZO electrical resistivity and promoting local atomic rearrangement, being the optimal temperature determined by the as-produced films' properties. For the best-performing transistors, even with a low annealing temperature (150°C), remarkable properties such as μFE =73.9 cm2 Vs, onoff ratio≈7× 107, VT ≈0.2 V, and S=0.29 Vdec are achieved. © 2008 The Electrochemical Society.

Solution based deposition has been recently considered as a viable option for low-cost flexible electronics. In this context research efforts have been increasingly centred on the development of suitable solution-processed materials for oxide based transistors. Nevertheless, the majority of synthetic routes reported require the use of toxic organic solvents. In this work we report on a new environmental friendly solution combustion synthesis route, using ethanol as solvent, for the preparation of indium/gallium free amorphous zinc-tin oxide (ZTO) thin film transistors (TFTs) including AlOx gate dielectric. The decomposition of ZTO and AlOx precursor solutions, electrical characterization and stability of solution processed ZTO/AlOx TFTs under gate-bias stress, in both air and vacuum atmosphere, were investigated. The devices demonstrated low hysteresis (ΔV=0.23 V), close to zero turn on voltage, low threshold voltage (VT=0.36 V) and a saturation mobility of 0.8 cm2 V-1 s-1 at low operation voltages. Ethanol based ZTO/AlOx TFTs are a promising alternative for applications in disposable, low cost and environmental friendly electronics. © 2015 IOP Publishing Ltd.

This paper deals with a new process to improve the stability of a-Si:H pin solar cells deposited in a single batch process by proper passivation of the interfaces. The process consists in removing partially a deposited sacrificial oxide layer grown between the p/i or i/n interfaces by SF6 etching. This layer is an absorber of defects and impurities that are introduced in the interfaces, mainly from the chamber walls and the substrate surface. The results achieved in laboratory samples lead to devices in which the fill factor and short circuit current density were improved respectively towards 75% and 16.5 mA cm-2, with a final working efficiency of about 9.5%. © 2001 Elsevier Science Ltd. All rights reserved.