Rodrigo Martins

We report the properties and optoelectronic applications of transparent and conductive indium and tin oxide films prepared by the spray pyrolysis method and doped with Sn or F, respectively. The film properties have been measured using X-ray diffraction, optical and electrical absorption. As examples of applications we produced a set of selective optical detectors for different spectral regions, covering the wavelength range from 0.25 to 1.1 μm, based on metal oxide-semiconductor heterostructures and using different substrates such as: GaP, GaSe, AlxGa1-xAs, GaAs and Si. The fabricated devices exhibit several features such as: production simplicity, high quantum efficiency, uniform sensitivity over the entire active area and a high response speed. Finally, we present a high quantum efficiency and solar blind monocrystalline zinc sulphide optical sensor fabricated by spray deposition as an alternative to the ultraviolet-enhanced SiC and GaN photodetectors and the performances of a solar cell. © 1998 Elsevier Science B.V. All rights reserved.

Electrochemically active bacteria (EAB) have the capability to transfer electrons to cell exterior, a feature that is currently explored for important applications in bioremediation and biotechnology fields. However, the number of isolated and characterized EAB species is still very limited regarding their abundance in nature. Colorimetric detection has emerged recently as an attractive mean for fast identification and characterization of analytes based on the use of electrochromic materials. In this work, WO 3 nanoparticles were synthesized by microwave assisted hydrothermal synthesis and used to impregnate non-treated regular office paper substrates. This allowed the production of a paper-based colorimetric sensor able to detect EAB in a simple, rapid, reliable, inexpensive and eco-friendly method. The developed platform was then tested with Geobacter sulfurreducens, as a proof of concept. G. sulfurreducens cells were detected at latent phase with an RGB ratio of 1.10 ± 0.04, and a response time of two hours.

The aim of this work is to interpret the role of the lateral leakage current on the a-Si:H solar cell performances (J-V characteristics, responsivity and the apparent device degradation behaviour), under low illumination conditions.

We report the architecture and the performances of a memory based on a single field-effect transistor built on paper able to write-erase and read. The device is composed of natural multilayer cellulose fibers that simultaneously act as structural support and gate dielectric; active and passive multicomponent amorphous oxides that work as the channel and gate electrode layers, respectively, complemented by the use of patterned metal layers as source/drain electrodes. The devices exhibit a large counterclockwise hysteresis associated with the memory effect, with a turn-on voltage shift between 1 and -14.5 V, on/off ratio and saturation mobilities of about 104 and 40 cm 2 V-1 s-1, respectively, and estimated charge retention times above 14 000 h. © 2008 American Institute of Physics.

The aim of this work is to present an analytical model which can to interpret the role of the collecting resistive layer on the static performances exhibited by 2D amorphous silicon hydrogenated p-i-n thin film position sensitive detectors. In addition, experimental results concerning the device linearity and spatial resolution are presented and checked against the predicted values of the analytical model proposed. © 1999 Elsevier Science S.A. All rights reserved.

This work aims to report results of the spatial and frequency optical detection limits of integrated arrays of 32 one-dimensional amorphous silicon thin film position sensitive detectors with nip or MIS structure, under continuous and pulsed laser operation conditions. The arrays occupy a total active area of 45 mm2 and have a plane image resolution better than 15 μm with a cut-off frequency of about 6.8 kHz. The non-linearity of the array components varies with the frequency, being about 1.6% for 200 Hz and about 4% for the cut-off frequency (6.8 kHz).

The aim of this work is to study the role of hydrogen dilution and filament temperature on the properties of nanocrystalline silicon thin films (undoped and doped) produced by the hot wire technique. These deposition parameters are correlated to the film's structure, composition and electro-optical properties with special emphasis on boron doped nanocrystalline silicon carbide reported here. © 1998 Elsevier Science B.V. All rights reserved.

A linear array thin film position sensitive detector (LTFPSD) based on hydrogenated amorphous silicon (a-Si:H) is proposed for the first time. Taking advantage of the optical properties presented by a-Si:H devices, we have developed a LTFPSD with 128 integrated elements able to be used in 3D inspections/measurements. Each element consists of a one-dimensional LTFPSD, based on a p-i-n diode produced in a conventional PECVD system, where the doped layers are coated with thin resistive layers to establish the required device equipotentials. By proper incorporation of the LTFPSD into an optical inspection camera it will be possible to acquire information about an object/surface, through the optical cross-section method. The main advantages of this system, when compared with the conventional CCDs, are the low complexity of hardware and software used and that the information can be continuously processed (analog detection). © 1995 American Institute of Physics.

Silicon oxycarbide microcrystallinc layers, n- and p-doped, highly conductive and highly transparent have been produced using a Two Consecutive Decomposition and Deposition Chamber (TCDDC) system. The films exhibit suitable properties for optoelectronic applications where wide band gap materials with required conductivity and stability are needed. In this paper we present the role of partial oxygen pressure (po2) in controlling the composition, structure and transport properties (conductivity. δd and optical gap, Eop) of silicon oxycarbide microcrystalline layers. © 1994 Materials Research Society.

This paper reports the performance of small area solar cells, 128 linear integrated position sensitive detector arrays and thin film transistors based on nanostructured silicon thin films produced by plasma-enhanced chemical vapour deposition technique, close to the onset of dusty plasma conditions, within the transition region from amorphous to microcrystalline. The small area solar cells, produced in a modified single chamber reactor, exhibited very good electrical characteristics with a conversion efficiency exceeding 9%. The 128 integrated position sensitive detector arrays, based on a similar pin structure, allow real-time 3D object imaging with a resolution higher than 90 l p/mm. The thin film transistors produced exhibited field effect mobility of 2.47 cm 2/V/s, threshold voltage of 2 V, on/off ratio larger than 10 7 and sub-threshold slopes of 0.32 V/decade, which are amongst the best results reported for this type of device. © 2009 Taylor & Francis.

The effects of Sn thickness electrodeposited over Cu on the structural and morphological performance of the joints formed were investigated. The electrical stability of the joints formed was analyzed under extreme aggressive conditions. Results indicated that the proposed soldering technology greatly satisfied the demands concerning soldering specifications.

This new production technique is based on the growth of a-Si films on a reactor where gas decomposition promoted by a capacitively coupled r. f. power system takes place in a chamber separated from that where amorphous films are deposited under the action of an electromagnetic static field. Using this method, we shall reduce films contamination caused by the residual gas desorbed from reactor walls. At the same time, there is a reduction plasma ion and electron damages on the deposited films. The main species impinging upon our substrates will be mainly composed of long life radicals with high mobilities and high diffusion rates, which will give origin to a random silicon network free of long poly-silane chains.

The process conditions of growing thin silicon films by plasma enhanced chemical vapour deposition (PECVD) were presented. The plasma impedance was found to monitor the powders in the PECVD systems and good quality silicon films were grown close to the plasma regime where the powders were formed. The silicon films exhibited properties which were interpreted based on a two-phase model where silicon nanostructures were embedded in a disordered network.

The aim of this paper was to present results of the role of the d.c. grid bias on the silane plasma impedance and its I-V characteristics to grow undoped amorphous silicon (a-Si:H) films by plasma enhanced chemical vapour deposition (PECVD) in conditions where some nanoparticles can be formed in the growth region of the deposition process, under proper ion bombardment. The results achieved show that the performances of the films produced are dependent on the self bias voltage that can present photosensitivities of approximately 107 (two orders of magnitude larger than the one exhibited by films grown under conventional conditions) with density of states determined by the constant photocurrent method below 4×1015 cm-3. Apart from that, the films grown are less affected by light soaking than the conventional films.

Amorphous Silicon solar cells have been produced by a two consecutive decomposition and deposition chamber system, using polished S. S. substrates. Through a systematic investigation of the electrical and optical properties of doped and undoped amorphous silicon layers (1) we observe that the deposition conditions (gas partial pressure, density of r. f. power, substrate temperature, electromagnetic static fields applied to the substrate, and gas flow rate) influence films properties. In the course of this investigation we have been studying the role of the sheet resistance, R//s, of the I. T. O. layer on the short circuit current, I//s//c, and on the open circuit voltage, V//o//c, of p. i. n. structures of 16cm**2 in area. The obtained results indicate that V//o//c is almost independent on R//s, while I//s//c variation approaches a square root dependence on R//s.

This paper deals with the growth process of nanostructured silicon films produced by chemical vapour deposition technique, at or close to the γ-regime where powders are formed. There, besides the set of chemical reactions undertaken by the species decomposed on the growth surface, the importance of the physics of the plasma in managing the powders and on the final film performances will be shown. To identify the plasma region where Si nanoaggregates are formed, we propose the use of a new parameter that translates the energy coupling of the rf power to the species of the gas flow, per pressure range of the process. By doing so we could establish an excellent correlation between this ratio and the plasma parameters such as peak to peak rf voltage and plasma impedance, or with the films defect density and their transport properties. Apart from that, we also show that high compact Si nanoclusters could be grown under moderate ion bombardment. Finally, to allow the growth at high rates of controlled silicon nanostructures, a three cycling process based on hot wire chemical vapour deposition and plasma assisting the hot wire technique will be discussed. © 2002 Elsevier Science Ltd. All rights reserved.

The aim of this work is to provide the basis for the interpretation, under steady state and in the low-voltage regime of the dark current-density-voltage (J-V) characteristics of transverse asymmetric amorphous silicon (a-Si:H) p-i-n and n-i-p diodes. The transverse asymmetric a-Si:H diodes present ratios between the metal contact and the underneath doped layer areas larger than five, leading to the inclusion, in the diode equation, of a lateral leakage current, responsible for the high saturation current density and the forward shape of the J-V curves recorded. The leakage current depends on the lateral spatial potential developed with which varies following a power-law dependence. The experimental J-V curves in diodes with the doped layer around the metal contact unetched and etched prove the role and origin of this lateral leakage current and, thus, the proposed model. © 1995 American Institute of Physics.

This paper discusses the effect of order and disorder on the electrical and optical performance of ionic oxide semiconductors based on zinc oxide. These materials are used as active thin films in electronic devices such as pn heterojunction solar cells and thin-film transistors. Considering the expected conduction mechanism in ordered and disordered semiconductors the role of the spherical symmetry of the s electron conduction bands will be analyzed and compared to covalent semiconductors. The obtained results show p-type c-Si/a-IZO/poly-ZGO solar cells exhibiting efficiencies above 14% in device areas of about 2.34 cm2. Amorphous oxide TFTs based on the Ga-Zn-Sn-0 system demonstrate superior performance than the polycrystalline TFTs based on ZnO, translated by ION/IOFF ratio exceeding 107, turn-on voltage below 1-2 V and saturation mobility above 25 cm2/Vs. Apart from that, preliminary data on p-type oxide TFT based on the Zn-Cu-O system will also be presented. © 2009 SPIE.

The electrosynthesis of polypyrrole (PPy) has been achieved on aluminium in aqueous medium of malic acid by means of cyclic voltammetry, potentiostatic and galvanostatic techniques. Scanning electron microscopy (SEM) and X-ray microanalysis by dispersion energy spectroscopy (EDS) applying on surfaces show that the PPy coating is developed from the metal surface through the cracks of the initial Al2O3 layer. Moreover, the results reveal that the homogeneity of the film achieved increases with the time of electropolymerization. A mechanism involving the participation of the supporting electrolyte and the pyrrole (Py) in distinct active sites was proposed based on the linear sweep voltammetry. It is observed for all the applied electrochemical techniques that the pyrrole concentration has to be higher than 0.1 M to allow the polypyrrole electrodeposition in acid medium. Scanning electron microscopy, secondary electrons (SE) and backscattering electrons (BE), shows that the PPy coating obtained in galvanostatic and potentiostatic modes starts with small islands at weak applied potentials or current densities. The corrosion results in 3% NaCl medium show that the PPy coating decreases the corrosion behaviour of the aluminium. The bilayer Al2O3/PPy shows a capacitor with future applications. © 2006 Elsevier B.V. All rights reserved.

We have deposited by Plasma Enhanced Chemical Vapour Deposition phosphorus doped amorphous and microcrystalline silicon films, as a function of the RF power (10-300 W), using a PH3/(SiH4 + H2 + He)mixture. It was found that films microcrystallization occurs for powers above 130 W, where a clear phase transition occurs. The microcrystalline films produced present high dark conductivities and optical band gaps, where the crystalline volume fraction is above 25%, as revealed by micro Raman spectroscopy. The Hall mobility have been also determined for amorphous and microcrystalline films, as a function of temperature, in the range 280-340 K. The data show that for the microcrystalline films the conduction is mainly in the extended states of the microcrystals, confirming also the double sign anomaly. That is, for n-type films, the sign is positive for the amorphous case while it is negative for the microcrystalline case. © 1998 Elsevier Science S.A.

Where a-Si:H pin devices are concerned, one of the main obstacles regarding improved performance is device stability, usually attributed to adverse behaviour at various interfaces within the device. Several attempts have been made to overcome this problem, such as the use of blocking layers at the interfaces. Although these have led to some improvements in device performance, most of the problems associated with device stability remain. This is mainly due to the defects at the interfaces, since the blocking layers (silicon alloys with carbon, nitrogen or oxygen) usually have a high density of bulk states, in comparison to intrinsic a-Si:H films. In this paper, we present a method that seems to be capable of improving device stability. It consists of performing a controlled removal of oxide interlayers at the interfaces, by an appropriate etching process. This enables the production of highly smoothed interfaces, and reduces possible cross-contamination of the i-layer from the adjacent doped layers. This amounts to a new design of typical pin devices, in which thin absorber layers are placed at the p/i and i/n interfaces. Their purpose is to trap most of the impurity atoms diffused from the doped layers, after which they are removed by appropriate etching. The fabrication of the absorbers (sacrificial layers), the nature of the etching and the tailoring of the defect profile at the interfaces will be discussed, including the performance exhibited by the resulting devices. © 2002 Elsevier Science B.V. All rights reserved.

Today there is a strong interest in the scientific and industrial community concerning the use of biopolymers for electronic applications, driven mainly by low-cost and disposable applications. Adding to this interest, we must recognise the importance of the dream of wireless auto-sustained and low-energy-consumption electronics. This dream can be fulfilled by cellulose paper, the lightest and the cheapest known substrate material, as well as the Earth's major biopolymer and of tremendous global economic importance. Most of the paper used up to now is optimised in terms of the required mechanical and physical properties to be used as the support of inks of different origins. In the future, specific electronic heterogeneous paper sheets should be fabricated aiming to get paper fibers with required bulk and surface functionalities, proper water/vapour barrier, size and diameter/thickness of the fibrils and full paper thickness. This will be the function of components/devices to be incorporated/integrated such as thin-film transistors, complementary metal oxide semiconductor devices, passive electronic components (resistances, inductors and capacitors), memory transistors, electrochromics and thin-film paper batteries. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The objective of this work is to provide a basis for the interpretation of the a-Si:H photodiode behaviour under low illumination level conditions, where a lateral leakage current plays an important role on the devices' performances when the doped collecting layer can not be considered a true equipotential. To determine this effect, a-Si:H p.i.n devices with small metal dot contacts, matrix distributed, were produced and analysed before and after etching the surrounding doped region of the metal collecting contact. The experimental data fit a model that includes the contribution of a lateral leakage current influencing the J-V characteristics, responsivity and the apparent light degradation behaviour of the device.

A study of intrinsic zinc oxide thin film as ozone sensor based on the ultraviolet (UV) photoreduction and subsequent ozone re oxidation of zinc oxide as a fully reversible process was presented. It was found that the film described were produced by spray pyrolysis, dc and rf magnetron sputtering. The dc resistivity of the films changed more than eight orders of magnitude when exposed to an UV dose of 4 mW/cm2. Analysis shows that the porous and textured zinc oxide films produced by spray pyrolysis at low substrate exhibit an excellent ac impedance response.

The role of order and disorder on the electronic performances of n -type ionic oxides such as zinc oxide, gallium zinc oxide, and indium zinc oxide used as active (channel) or passive (drain/source) layers in thin film transistors (TFTs) processed at room temperature are discussed, taking as reference the known behavior observed in conventional covalent semiconductors such as silicon. The work performed shows that while in the oxide semiconductors the Fermi level can be pinned up within the conduction band, independent of the state of order, the same does not happen with silicon. Besides, in the oxide semiconductors the carrier mobility is not bandtail limited and so disorder does not affect so strongly the mobility as it happens in covalent semiconductors. The electrical properties of the oxide films (resistivity, carrier concentration, and mobility) are highly dependent on the oxygen vacancies (source of free carriers), which can be controlled by changing the oxygen partial pressure during the deposition process and/or by adding other metal ions to the matrix. In this case, we make the oxide matrix less sensitive to the presence of oxygen, widening the range of oxygen partial pressures that can be used and thus improving the process control of the film resistivity. The results obtained in fully transparent TFT using polycrystalline ZnO or amorphous indium zinc oxide (IZO) as channel layers and highly conductive poly/nanocrystalline ZGO films or amorphous IZO as drain/source layers show that both devices work in the enhancement mode, but the TFT with the highest electronic saturation mobility and on/off ratio 49.9 cm2 V s and 4.3× 108, respectively, are the ones in which the active and passive layers are amorphous. The ZnO TFT whose channel is based on polycrystalline ZnO, the mobility and on/off ratio are, respectively, 26 cm2 V s and 3× 106. This behavior is attributed to the fact that the electronic transport is governed by the s -like metal cation conduction bands, not significantly affected by any type of angular disorder promoted by the 2p O states related to the valence band, or small amounts of incorporated metal impurities that lead to a better control of vacancies and of the TFT off current. © 2007 American Institute of Physics.