Rodrigo Martins

Thick films of cordierite-based glass ceramics were prepared by aqueous tape casting from suspensions containing 80-wt% solids. The weight proportions of cordierite/glass ranged from 70/30 to 30/70 in order to investigate the effect of glass content on the rheological behaviour and on the microstructures and properties of the green tapes. Suspensions with 50 to 60-wt% glass content exhibited the lowest viscosity values among all the slurries investigated, while the green tape containing 30-wt% glass presented homogenous microstructures at both top and bottom surfaces, contrarily to the observations for the other compositions. The green densities increased with glass content. The sintered tapes (1150°C, 2h) containing 50 to 60-wt% glass exhibited the lowest values for the dielectric constant (∼5.2) and dielectric loss (∼0.002) at 1MHz.

Today there is a strong interest in the scientific and industrial community concerning the use of biopolymers for electronic applications, mainly driven by low-cost and disposable applications. Adding to this interest, we must recognize the importance of the wireless auto sustained and low energy consumption electronics dream. This dream can be fulfilled by cellulose paper, the lightest and the cheapest known substrate material, as well as the Earth's major biopolymer and of tremendous global economic importance. The recent developments of oxide thin film transistors and in particular the production of paper transistors at room temperature had contributed, as a first step, for the development of disposable, low cost and flexible electronic devices. To fulfil the wireless demand, it is necessary to prove the concept of self powered devices. In the case of paper electronics, this implies demonstrating the idea of self regenerated thin film paper batteries and its integration with other electronic components. Here we demonstrate this possibility by actuating the gate of paper transistors by paper batteries. We found that when a sheet of cellulose paper is covered in both faces with thin layers of opposite electrochemical potential materials, a voltage appears between both electrodes - paper battery, which is also self-regenerated. The value of the potential depends upon the materials used for anode and cathode. An open circuit voltage of 0.5V and a short-circuit current density of 1μA/cm2 were obtained in the simplest structure produced (Cu/paper/Al). For actuating the gate of the paper transistor, seven paper batteries were integrated in the same substrate in series, supplying a voltage of 3.4V. This allows proper ON/OFF control of the paper transistor. Apart from that transparent conductive oxides can be also used as cathode/anode materials allowing so the production of thin film batteries with transparent electrodes compatible with flexible, invisible, self powered and wireless electronics. © 2011 SPIE.

This paper presents the characterization of fundamental analog and digital circuits with a-IGZO TFTs from measurements performed at normal ambient. The fundamental blocks considered in this work include digital logic gates, a low-power single stage high-gain amplifier with capcacitive bootstrapping and a level shifter/buffer. These circuits are important functional blocks in analog/Mixed signal IC design with oxide TFTs. Being fabricated at low temperature (< 200 °C), they can find potential applications in low-cost large-area flexible systems. © 2016 IEEE.

This paper addresses a modeling and simulation methodology for analog circuit design with amorphous-GIZO thin-film transistors (TFTs). To reach an effective circuit design flow, with commercially available tools, a TFT model has been first developed with an artificial neural network (ANN). Multilayer perceptron with backpropagation algorithm has been adopted to model the static behavior of the TFT devices, for different aspect ratios. The model was then implemented in Verilog-A, to allow a quick instantiation in circuit. Simulations using Cadence Spectre are performed to validate the model. On a second phase, simulation results of basic analog circuits, with this ANN model, are verified against the actual functional results, namely an adder, subtractor, and current mirror circuit. Results demonstrate not only the ANN model accuracy and compatibility with dc and transient analysis, but also show the a-GIZO TFT capability to perform analog operations. © 2012 IEEE.

This work reports a technique to obtain electronic grade intrinsic amorphous silicon using the plasma enhanced chemical vapour deposition technique at 13.56 MHz. The batch processing method consists of igniting the plasma process through a neutral gas such as hydrogen or helium and only feeding the carrier gas containing the species to be decomposed into the reactor when the plasma is stabilized. By doing so, no surface damage is induced in the first deposited layers and so a more compacted and stable film is produced, compared to amorphous films grown by conventional methods. The best deposition conditions to produce films with good transport properties for optoelectronic applications are: temperature ≈ 473 K, 60 < pressure 87 Pa, power density of 32 mW/cm2 and flow of silane ≈ 10 sccm. The growth rate and the microstructure factor are 1.5 Å/s and 3.3×10-2, respectively, while the activation energy ≈ 0.8 eV; dark conductivity at room temperature ≈ 4.37×10-10 (ωcm)-1; photosensiti-vity ≈ 5.02×l06; density of states ≈ 6.6×1015 cm-3; bonded hydrogen concentration ≈ 20 at% and optical band gap ≈ 1.75 eV.

The behaviour of a microcrystalline p-i-n junction locally illuminated with monochromatic radiation (incident power of 50 mW/cm2) is analysed by means of numerical experiences. The model used for the two-dimensional analysis of the transport properties of a μc-Si:H p-i-n photo-detector is based on the simultaneous solution of the continuity equations for holes and electrons together with the Poisson's equation. The solution is found on a rectangular domain, taking into account the dimension perpendicular to the junction plane and one on the parallel plane. The lateral effects occurring within the structure, due to the non-uniformity of the illumination, are outlined. The results we present show that the potential profile has a linear variation from the illuminated to the dark neutral region. The lateral components of the electric field and of the current density vectors reveal to be mainly localised inside the doped layers.

We have projected and fabricated a microfluidic platform for DNA sensing that makes use of an optical colorimetric detection method based on gold nanoparticles. The platform was fabricated using replica moulding technology in PDMS patterned by high-aspect-ratio SU-8 moulds. Biochips of various geometries were tested and evaluated in order to find out the most efficient architecture, and the rational for design, microfabrication and detection performance is presented. The best biochip configuration has been successfully applied to the DNA detection of Mycobacterium tuberculosis using only 3. l on DNA solution (i.e. 90. ng of target DNA), therefore a 20-fold reduction of reagents volume is obtained when compared with the actual state of the art. © 2013 Elsevier B.V.

The intense light scattered from metal nanoparticles sustaining surface plasmons makes them attractive for light trapping in photovoltaic applications. However, a strong resonant response from nanoparticle ensembles can only be obtained if the particles have monodisperse physical properties. Presently, the chemical synthesis of colloidal nanoparticles is the method that produces the highest monodispersion in geometry and material quality, with the added benefits of being low-temperature, low-cost, easily scalable and of allowing control of the surface coverage of the deposited particles. In this paper, novel plasmonic back-reflector structures were developed using spherical gold colloids with appropriate dimensions for pronounced far-field scattering. The plasmonic back reflectors are incorporated in the rear contact of thin film n-i-p nanocrystalline silicon solar cells to boost their photocurrent generation via optical path length enhancement inside the silicon layer. The quantum efficiency spectra of the devices revealed a remarkable broadband enhancement, resulting from both light scattering from the metal nanoparticles and improved light incoupling caused by the hemispherical corrugations at the cells' front surface formed from the deposition of material over the spherically shaped colloids. © 2015 IOP Publishing Ltd.

Indium doped, and undoped, zinc oxide films were deposited using aerosol assisted chemical vapour deposition (AACVD) at atmospheric pressure on glass substrates. Electrical measurements (I-V) showed a reduction in resistivity following the addition of indium, and XRD analysis revealed an associated switch to c-axis preferred crystal orientation. The ability of the films to oxidise organic material on their surface was analysed using stearic acid as the model contaminant under ultra-violet (UV, 365 nm) irradiation. The In-doped films displayed a greater rate of organic decomposition, which we attribute to the formation of a platelet surface structure having a larger surface area than the undoped films, on which the UV generated electrons and holes may react to form active photocatalytic species. In addition we suggest that the switch to c-axis crystal orientation may reduce the electron-hole pair recombination rate at the grain boundaries, due to an improvement in crystallinity and related reduction in carrier scattering losses, leading to an increase in photocatalytic organic decomposition rate. © 2011 Elsevier B.V. All rights reserved.

The increasing demand in automation processes in finishing techniques also calls for automatic measurement and inspection methods. These methods ought to be installed as close as possible to the production process and they ought to measure the values needed in a safe and fast way, without disturbing the process itself. Simultaneously they should be free of wear and insensitive against mechanical perturbations. This approach can be reached by proper combination of the laser triangulation technique with an array of linear position sensitive detectors, able to supply information about the surface finishing of an object. This is the aim of this paper that envisages to present experimental results of the performances exhibited by such an array constituting 128 elements. The analogue information supplied by this array is processed by an analogue/digital converter, directly coupled to the array and whose information is computer processed, concerning the recognition of patterns and the processing of information collected over the object to be inspected. © 1999 Elsevier Science S.A. All rights reserved.

We report, for the first time, results on transparent ZnO:Al thin films deposited on polyester (Mylar type D, 100 μm thickness) substrates at room temperature by magnetron sputtering. The structural, optical and electrical properties of the deposited films have been studied. The samples are polycrystalline with a hexagonal wurtzite structure and a strong crystallographic c-axis orientation (0 0 2) perpendicular to the substrate surface. The ZnO:Al thin films with 83% transmittance in the visible region and a resistivity as low as 3.6 × 10-2 Ωcm have been obtained, as deposited. The obtained results are comparable to those obtained on glass substrates, opening a new field of low cost, light weight, small volume, flexible and unbreakable large area optoelectronic devices. © 2002 Elsevier Science Ltd. All rights reserved.

Amorphous silicon carbide films were obtained by plasma enhanced chemical vapor deposition (PECVD) technique using a gas mixture of silane, methane, and hydrogen with a high excitation frequency and a high hydrogen dilution ratio. The high temperature annealing behavior of the amorphous silicon carbide films was studied by annealing at 1373 K for 1 h in nitrogen atmosphere. A very thin Au film was deposited on part of the films to investigate the metal induced crystallization effect. Well aligned nanotubes were found on the silicon carbide films covered by a thin gold layer after the high temperature annealing by atomic force microscopy. Further study is necessary to identify the nature of the nanotubes and elucidate their growth mechanism. © 2006 Elsevier B.V. All rights reserved.

In this work Spectroscopic Ellipsometry (SE) was used to study metal induced crystallization (MIC) on amorphous silicon films in order to analyze the influence of different annealing conditions on their structural properties. The variation of the metal thickness has shown to be determinant on the time needed to full crystallize silicon films. Films of 100 nm thickness crystallize after 2h at 500°C using 1 nm of Ni deposited on it. When reducing the average metal thickness down to 0.05 nm the same silicon film will need almost 10 hours to be totally crystallized. Using a new approach on the modelling procedure of the SE data we show to be possible to determine the Ni remaining inside the crystallized films. The method consists in using Ni as reference on the Bruggeman Effective Medium Approximation (BEMA) layer that will simulated the optical response of the crystallized silicon. Silicon samples and metal layers with different thicknesses were analyzed and this new method has shown to be sensible to changes on the initial metal/silicon ratio. The nickel distribution inside the silicon layers was independently measured by Rutherford Backscattering Spectroscopy (RBS) to check the data obtained from the proposed approach. © 2006 Materials Research Society.

Nanotechnology is having a positive impact on nearly every industry, and in particular in healthcare, where it is extending the limits of molecular diagnostics to the nanoscale-nanodiagnostics. Here we describe an innovative optoelectronic platform for the colorimetric detection of nucleic acids based on oligonucleotide-derivatized gold nanoparticles. The device integrates an amorphous/nanocrystalline biosensor and a light emission source with a gold nanoprobe for specific DNA detection. This low cost, fast and simple optoelectronic platform permits detection of few picomole of nucleic acid without target or signal amplification making it suitable for application in population diagnostics and in point-of-care hand-held devices. © 2007 Elsevier B.V. All rights reserved.

Polymorphous silicon (pm-Si:H) films have been prepared by a new regime of plasma enhanced chemical vapour deposition in the region adjacent of phase transition from amorphous to microcrystalline state. Comparing to the conventional amorphous silicon (a-Si:H), the pm-Si:H has higher photoconductivity (σph), better stability, and a broader light spectral response range in the longer wavelength range. It can be found from Raman spectra that there is a notable improvement in the medium range order. There are a blue shift for the stretching mode of IR. spectra and a red shift for the wagging mode. The shifts are attributed to the variation of the microstructure. By using pm-Si:H film as intrinsic layer, a p-i-n junction solar cell was prepared with the initial efficiency of 8.51% and a stabilized efficiency of 8.01% (AM1.5, 100mw/cm2) at room temperature (T R).

A series of hydrogenated amorphous silicon carbide (a-Si 1- xC x:H) films were prepared by plasma-enhanced chemical vapour deposition (PECVD) using a gas mixture of silane, methane, and hydrogen as the reactive source. The previous results show that a high excitation frequency, together with a high hydrogen dilution ratio of the reactive gases, allow an easier incorporation of the carbon atoms into the silicon-rich a-Si 1-xC x:H film, widen the valence controllability. The data show that films with optical gaps ranging from about 1.9 to 3.6 eV could be produced. In this work the influence of the hydrogen dilution ratio of the reactive gases on the a-Si 1-xC x:H film properties was investigated. The microstuctural and photoelectronic properties of the silicon carbide films were characterized by Rutherford backscattering spectrometry (RBS), elastic recoil detection analysis (ERDA), and FT-IR spectrometry. The results show that a higher hydrogen dilution ratio enhances the incorporation of silicon atoms in the amorphous carbon matrix for carbon-rich a-Si 1-xC x:H films. One pin structure was prepared by using the a-Si 1-xC x:H film as the intrinsic layer. The light spectral response shows that this structure fits the requirement for the top junction of colour sensor. © 2004 Elsevier B.V. All rights reserved.

A series of hydrogenated amorphous silicon carbide films were prepared by plasma enhanced chemical vapor deposition (PECVD) using a gas mixture of silane, methane, and hydrogen as the reactive source and an excitation frequency of 27.12 MHz. Compared to the typical radio frequency deposition technique, the very high plasma excitation frequency increases the density of the electrons and decreases the electron temperature, which helps the dissociation of the SiH4 and CH4, and reduces the energetic ion impact on the growth surface of the thin film. Thus, dense-films with lower bulk density of states and higher growth rate are expected, as confirmed by spectroscopic ellipsometry data. Apart from that, a substantial reduction of bulk defects is achieved, allowing an improvement of the valence controllability (widening of the optical gap from about 1.9 to 3.6 eV). In this work results concerning the microstuctural and photoelectronic properties of the silicon carbide films will be discussed in detail, correlating them with the deposition process conditions used as well as with the gas phase composition of the mixtures used. © 2004 Elsevier B.V. All rights reserved.

The aim of this paper is to compare the density of bulk states (DOS) of polymorphous silicon (pm-Si:H) films produced by plasma enhanced chemical vapor deposition at 13.56 and 27.12 MHz using the constant photocurrent method and the space charge limited current (SCLC) technique. The data achieved revealed that the set of films produced present similar DOS. Apart from that, data concerning the correlation of the deposition conditions that lead to the production of pm-Si:H as well as their characteristics, such as the hydrogen content and how hydrogen is bonded, will be discussed, giving special emphasis to the set of mechanical stresses developed. By doing so we could get a better understanding of the nature of hydrogen bonding in pm-Si:H films as well as to determine the role of the excitation frequency on the film's performances, where films with amounts of hydrogen around 20 at.% can have DOS as low as 8 × 10 14 cm-3 with Urbach energies in the range of 41-50 meV. © 2004 Elsevier B.V. All rights reserved.

Gallium-doped zinc oxide films were prepared by rf magnetron sputtering at room temperature as a function of the substrate-target distance. The best results were obtained for a distance of 10 cm, where a resistivity as low as 2.7×10-4 Ωcm, a Hall mobility of 18 cm2/Vs and a carrier concentration of 1.3×1021 cm-3 were achieved. The films are polycrystalline presenting a strong crystallographic c-axis orientation (002) perpendicular to the substrate. The films present an overall transmittance in the visible part of the spectra of about 85 %, in average. The low resistivity, accomplished with a high growth rate deposited at RT, enables the deposition of these films onto polymeric substrates for flexible applications.

Aluminium doped zinc oxide thin films (ZnO:Al) have been deposited on polyester (Mylar type D, 100 μm thickness) substrates at room temperature by r.f. magnetron sputtering. The structural, morphological, optical and electrical properties of the deposited films have been studied. The samples are polycrystalline with a hexagonal wurtzite structure and a strong crystallographic c-axis orientation (002) perpendicular to the substrate surface. The ZnO:Al thin films with 85% transmittance in the visible and infra-red region and a resistivity as low as 3.6×10-2 Ωcm have been obtained, as deposited. The obtained results are comparable to those ones obtained on glass substrates, opening a new field of low cost, light weight, small volume, flexible and unbreakable large area optoelectronic devices.

The present work reports charging effects and surface potential variations in pure copper, cuprous oxide and cupric oxide nanowires observed by electrostatic force microscopy (EFM) and Kelvin probe force microscopy (KPFM). The copper nanowires were produced by wet synthesis, oxidation into cuprous oxide nanowires was achieved through microwave irradiation and cupric oxide nanowires were obtained via furnace annealing in atmospheric conditions. Structural characterization of the nanowires was carried out by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and energy dispersive X-ray spectroscopy. During the EFM experiments the electrostatic field of the positive probe charged negatively the Cu-based nanowires, which in turn polarized the SiO2 dielectric substrate. Both the probe/nanowire capacitance as well as the substrate polarization increased with the applied bias. Cu2O and CuO nanowires behaved distinctively during the EFM measurements in accordance with their band gap energies. The work functions (WF) of the Cu-based nanowires, obtained by KPFM measurements, yielded WFCuO > WFCu > WFCu2O. © 2015 Elsevier B.V.

N, (N+Ga) and (N+Al) doped ZnO films were deposited on c-plane sapphire substrates by RF magnetron sputtering at room temperature. The samples were characterized by their structural, surface morphological, compositional and optical properties. The x-ray diffraction studies confirmed the co-doping of (N+Ga) and (N+Al) besides showing improvement in the crystallinity when compared with the single Ndoping. The surface of the films becomes rougher after co-doping. The x-ray photoelectron spectroscopy and Rutherford back-scattering analysis indicate that the co-doping changes the chemical states and varies the amount of nitrogen (N) in ZnO. The amount of 'N' has been greatly increased for (N+Ga) co-doping, indicating that it is the best co-doping pair for p-type ZnO. Additionally, co-doping has increased the average visible transmittance (40-650nm) and the optical band gap is shifted towards shorter wavelength. In the case of (N+Al) co-doping, the band gap becomes wider than that of undoped ZnO. © IOP Publishing Ltd.

The color sensing ability of a data acquisition prototype system integrating a 32 linear array of 1D amorphous silicon position sensitive detectors (PSD) was analyzed. Besides being used to reproduce a 3D profile of highly reflective surfaces, here we show that it can also differentiate primary red, green, blue (RGB) and derived colors. This was realized by using an incident beam with a RGB color combination and adequate integration times taking into account that a color surface mostly reflects its corresponding color. A mean colorimetric error of 25.7 was obtained. Overall, we show that color detection is possible via the use of this sensor array system, composed by a simpler amorphous silicon pin junction. © 2013 Elsevier B.V. All rights reserved.

Aluminum Zinc Oxide has been extensively investigated as a cheap alternative to transparent conducting tin oxide films for electronic and optoelectronic applications. Thin films of Aluminum Zinc Oxide have been developed successfully through a combination of solution combustion synthesis and solution synthesis. Zn(NO3)3·6H2O as metal source was dissolved in 2-methoxyethanol as solvent through combustion synthesis with Urea as fuel while dopant source of AlCl3·6H2O was mixed separately in solvent to avoid aluminum oxide formation in the films. Precursor solutions were obtained mixing Zn & Al separate solutions in 9:1, 8:2, and 7:3 ratios respectively with oxide, fuel and dopant concentrations of 0.5, 0.25, 0.1, and 0.05 M. The film stacks have been prepared through spin-coating with heating at 400°C for 10 minutes after each deposition to remove residuals and evaporate solvents. Thermal annealing in oven at 600°C for 1 hour followed by rapid thermal annealing at 500°C & 600°C first in vacuum and then in N2-5%H2 environment respectively for 10 minutes each reduced the resistivity of film stacks. Film stack with 10 layers for an average thickness of 0.5μm gave the best Hall Effect resistivity of 3.2 × 10-2 -cm in the case of 0.5M solution with Zn:Al mixing ratio of 9:1 for RTA annealings at 600°C with an average total transparency of 80 % in the wavelength range of 400-1200 nm. The results show a clear trend that increasing the amount of ingredients resistivity could further be decreased. © 2015 IEEE.

Amorphous undoped a-Si:H films have been produced by hot wire plasma assisted chemical vapour deposition (HWPA-CVD), which combines the hot wire chemical vapour deposition (HW-CVD) and plasma enhanced chemical vapour deposition techniques. In this work we analyse the dissociation mechanism of the gas during the film growth in both processes with a quadrupole mass spectrometer. Besides that, the energy delivered to the gas dissociation is determined and correlated with the films properties. Thus, based on the results of the dissociated species for each deposition condition and process, we explain why the growth rate is enhanced when the filament temperature rises in HW-CVD process and why it decreases as r.f. power is enhanced in HWPA-CVD process. © 2002 Elsevier Science B.V. All rights reserved.