Rodrigo Martins

The aim of this paper is to present results concerning the morphology, structure, mechanical and electrical characteristics of the new proposed Cu-Sn metallurgical alloy, which may be used in electronic joins. By proper choice of process temperature and pressure, Cu coated surfaces are soldered using Sn as pre-form. The main results achieved indicate that the formation of Cu3Sn phase begins at a temperature of about 473 K and that the Sn thickness (dSn) needed is slightly above 7 μm. Due to join wettability, higher temperatures (between 523 and 573 K) and dSn above 35 μm are required to form joins within the specifications of the electronic industry.

This work deals with the role of hydrogen dilution and filament temperature on the morphology, structure and electrical properties of nanocrystalline boron doped silicon carbide thin films produced by hot-wire technique. The structural and morphological data obtained by XRD, SEM and micro-Raman show that for filament temperatures and hydrogen dilutions above 2100 °C and 90%, respectively, the surface morphology of the films is granular with a needle shape, while for lower filament temperatures and hydrogen dilutions the surface morphology gets honeycomb like. The SIMS analysis reveals that films produced with filament temperatures of about 2200 °C and hydrogen dilution of 99% present a higher hydrogen and carbon incorporation than the films produced at lower temperatures and hydrogen dilutions. These results agree with the electrical and optical characteristics recorded that show that the films produced exhibit optical gaps in the range from 1.8 to 2 eV and transverse conductivities ranging from 10-1 S/cm to 10-3 S/cm, consistent with the degree of films crystallinity and carbon incorporation recorded.

This paper reports results on the role of high hydrogen dilution (above 80%) on the electro-optical and structural properties of boron doped silicon films produced by hot wire chemical vapor deposition (HW-CVD) technique, keeping constant the filament temperature. The structural, compositional, morphological, electrical and optical properties achieved show that the films present excellent homogeneity over the entire 10 x 10 cm deposited area. These results were obtained for films produced at gas pressures below 66.5 Pa, in spite of the high flow rate used. © 2001 Elsevier Science B.V. All rights reserved.

This work reports the use of undoped porous amorphous/nanocrystalline hydrogenated silicon (a/nc-Si:H) thin films produced by hot wire chemical vapour deposition (HW-CVD) as ethanol detector above 50ppm and as a primary fuel cell where a power of 4μW/cm2 was obtained in structures of the type glass/ITO/i-a-nc-Si:H/Al. The porous silicon looks like a sponge constituted by grains and cluster of grains that determines the type of surface morphology and the behaviour of the structure under the presence of vapour moisture. Apart from that, the detector/device performances will also depend on the type of interlayer and interfaces with the metal contacts. The sponge like structure adsorbs the OH groups in uncompensated bonds, which behave as donor-like carriers, leading to an increase in the current flowing through the material, directly dependent on the ethanol vapour pressure. The corresponding role of the components of the microstructure on this detector was investigated by spectroscopic impedance. The response time of the current of the sensor and its recovery time are in the range of 10-50s at room temperature. © 2004 Elsevier B.V. All rights reserved.

Doped a/μc-Si:H films were produced in different starting deposition conditions by the hot wire chemical vapor deposition technique. In this paper, we show that by changing the initial onset deposition conditions of the process and maintaining the overall pressure, hydrogen dilution and filament temperature, it is possible to control the compactness of the films. As the films nucleation is the key parameter to produce compact films, we show that starting the process with hydrogen and progressively introducing the process gas enhances the compactness and improve the electrical properties of the films produced. © 2002 Elsevier Science B.V. All rights reserved.

In this work, we present the properties of n-type silicon films obtained by hot wire plasma assisted technique produced at different rf power and gas flow rate. The films were produced at a filament temperature of 2000°C and the rf power was varied from 0 W to 200 W while gas flow rate was varied from 15 to 100 sccm keeping rf power at 50 W. In this flow rate range, the growth rate of the films varied from 5Å/s to 250Å/s and the corresponding electrical room dark conductivity varied from 10-2 to 10(Ωcm)-1. On the other hand, we observed that the electrical conductivity increased from 2 to 6(Ωcm)-1, and the Hall mobility from 0.1 to 2 cm2/V.s as rf power change from 0 W to 200 W. The infrared, EDS and XPS analyses revealed the existence of oxygen incorporation, which is not related to post-deposition oxidation. The X-ray diffraction and μRaman data show the presence of Si crystals in the films structure and the SEM micrographs reveal a granular surface morphology with grain sizes lower than 60 nm.

In this paper, we present results of the role of laser beam energy and shot density on the electro-optical and structural properties of undoped and doped recrystallized amorphous silicon thin films, generated by pulsed Nd-YAG laser (λ = 532 nm). The data reveal that the structure and electrical characteristics of the recrystallized thin films are mainly dependent on the energy and shot density of the laser beam, while the morphology of the obtained films are mainly governed by the number of shots used. The data also show that the electrical conductivity of undoped and doped recrystallized films can be varied up to 6 orders of magnitude, by the proper choice of the recrystallization conditions. Doped samples with conductivities in the amorphous states in the range of 10-5 Ω-1 cm-1 present, after recrystallization, conductivities of about 300 Ω-1 cm-1. The SEM micro-chemical analysis also shows that the obtained crystalline grains are constituted by pure silicon. © 1998 Elsevier Science S.A.

This work analyse mainly the dissociation mechanism of the gas during the hot wire (HW) and hot wire plasma-assisted (HWPA) processes used to produce hydrogenated carbon films and silicon-carbide, using ethylene and silane as gas sources. The results show that ethylene is better decomposed by plasma-enhanced chemical vapour deposition (PECVD) than HW process. The data also show that the HWPA leads to a better carbon © incorporation than HW processes, when silicon carbide alloys are produced and, that the presence of atomic hydrogen (H) is beneficial for all processes. That is, the presence of the plasma and H lead to the formation of higher C radicals such as methylsilane (CH3SiH3), ethylsilane (C2H5SiH3) and silorane (C2H4SiH2), whose contributions are enhanced as the fraction of ethylene (Feth) in the gas mixture increases. © 2001 Published by Elsevier Science B.V.

A commercial sheet of paper based on natural cellulose fibers acting as permeable membrane with thin film metal cathode (Cu) and anode (Al) layers in each face was used to produce paper batteries that could be interconnected in series and rechargeable using water as electrolyte. Their electrical characteristics and the set of electrochemical reactions that support the experimental behavior observed are described in this paper. A series of integrated batteries able to supply a voltage of about 3 V and a current ranging from 0.7 μA to 25 μA in cells with sizes of 1.2 cm × 3.0 cm for a relative humidity in the range of 50-65% were produced in a single sheet of paper, and successfully applied to control the ON/OFF gate state of paper transistors. © 2010 Elsevier Ltd. All rights reserved.

In this work we studied the influence of hydrogen dilution, rf power, and the filament and substrate temperatures on the electro-optical properties and composition of a-Si:H films produced by hot wire plasma assisted technique. The a-Si:H films were produced on Mylar substrates with growth rate of up to 37 Å/s, ημτ product of 1.6 × 10-7 cm2/V, photoconductivity to dark conductivity ratio of 1 × 104 (at AM1.5 radiation), and a dark conductivity of about 10-10 (Ω cm)-1 for substrate temperature of 130 °C, hydrogen dilution of 99%, filament temperature of 1700 °C, and rf power of 100 W. © 2002 Elsevier Science B.V. All rights reserved.

The role of the deposition pressure (p) and the type of filaments (tungsten, W or tantalum, Ta) used to produce large area (10cm×10cm) n-type Si:H films by hot wire chemical vapour (HW-CVD) deposition technique was investigated. The data show that the electro-optical properties of the films produced are dependent on the gas pressure used. In the pressure range of 1×10-3 Torr to 1.0 Torr, the room dark conductivity (σd) varies from 1×10-8 to 2 S/cm for films produced at the same hydrogen dilution and filament temperature (Tfil). On the other hand, the hydrogen concentration (CH) decreases from 10% to 2%, while the growth rate (R) shows an exponential increase, from 1 to 9 Å/s. The SIMS analysis, within the detection limits, does not reveal the existence of any significant W or Ta contamination in the films produced.

This work reports on the performances of undoped and n doped amorphous/nano-crystalline silicon films grown by hot wire plasma assisted technique. The film's structure (including the presence of several nanoparticles with sizes ranging from 5 nm to 50 nm), the composition (oxygen and hydrogen content) and the transport properties are highly dependent on the filament temperature and on the hydrogen dilution. The undoped films grown under low r.f. power (≈4 mWcm-2) and with filament temperatures around 1850 °K have dark conductivities below 10-10 Scm-1, optical gaps of about 1.5 eV and photo-sensitivities above 105, (under AM1.5), with almost no traces of oxygen content. N-doped silicon films were also fabricated under the same conditions which attained conductivities of about 10-2 Scm-1.

In this work, we show the possibility to use undoped porous silicon (PS) thin films produced by hot wire chemical vapour deposition technique (HW-CVD) as ethanol detector. Silicon thins films produced by HW-CVD technique, under certain deposition conditions, have a porous structure [Vacuum 52 (1999) 147]. Therefore, in the presence of an alcohol, the OH group is adsorbed by the uncompensated bonds behaving as donor-like carriers leading to an increase in the current flowing through the material. This current enhancement is bias dependent in glass/ITO/i-a-Si:H/Al sensor and increases as the ethanol vapour pressure increases from 10-1mbar to atmospheric pressure. The response time of the current of the sensor and its recovery time are in the range of 10-50s at room temperature. Ethanol quantities above 50ppm can be detected. © Published by Elsevier B.V.

Electrospun fibers of poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-bithiophene] (F8T2) with exceptional electro-optical performance are obtained. The I/T characteristics measured in fibers with 7-15 μm diameter and 1 mm length show a semiconductor behavior; their thermal activation energy is 0.5 eV and the dark conductivity at RT is 5 × 10-9 (Ω cm)-1. Besides exhibiting a photosensitivity of about 60 under white light illumination with a light power intensity of 25 mW · cm-2, the fibers also attain RT photoluminescence in the cyan, yellow, and red wavelength range under ultraviolet, blue, and green light excitation, respectively. Optical microscope images of F8T2 reveal homogeneous electrospun fibers, which are in good agreement with the uniformly radial fluorescence observed. The production of electrospun fibers from poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-bithiophene] (F8T2) obtained without a carrier polymer is reported. The obtained fibers are shown to have properties suitable for organic fiber photovoltaic and sensors applications. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydrogenated silicon carbon nitride (SiCN:H) thin film alloys were produced by hot wire (HWCVD), plasma assisted hot wire (PA-HWCVD) and plasma enhanced chemical vapor (PECVD) deposition techniques using a Ni buffer layer as catalyst for inducing crystallization. The silicon carbon nitride films were grown using C2H4, SiH4 and NH3 gas mixtures and a deposition temperature of 300 °C. Prior to the deposition of the SiCN:H film a hydrogen etching of 10 min was performed in order to etch the catalyst material and to facilitate the crystallization. We report the influence of each deposition process on compositional, structural and morphological properties of the films. Scanning Electron Microscope-SEM and Atomic Force Measurement-AFM images show their morphology; the chemical composition was obtained by Rutherford Backscattering Spectrometry-RBS, Elastic Recoil Detection-ERD and the structure by Infrared-IR analysis. The thickness of the catalyst material determines the growth process and whether or not islands form. The production of micro-structured SiCN:H films is also dependent on the gas pressure, gas mixture and deposition process used. © 2006 Elsevier B.V. All rights reserved.

This paper reports on a method and a test setup developed to measure the transient dark current and the spectral response characteristics of a-Si:H MIS photosensors. Using this method the segmented-gate/SiNx/a Si:H/n +/ITO structures have been characterized under different biasing conditions. The dependences of the dark and light signals on the refresh pulse amplitude, offset voltage and pulse width were measured and analyzed. It is found that the amplitude of the time-dependent component of the leakage current associated with charge trapping at the insulator-semiconductor interface can be significantly reduced by adjusting the offset voltage. The observed bias dependence of the spectral response characteristics is explained by analyzing the charge carrier transport in the absorption layer at different wavelengths of the incident light. © 2008 WILEY-VCH Verlag GmbH & Co. KGaA.

The working principle of silicon p-i-n structures with low conductivity (σd) doped layers as single element image sensors is based on the modulation, by the local illumination conditions of the photocurrent generated by a light beam scanning the active area of the device. A higher sensitivity is achieved using a wide band gap a-Si:C alloy in the doped layers, improving the light penetration into the intrinsic semiconductor and reducing the lateral currents in the structure, which are responsible by an image smearing effect observed in sensors with high σd doped layers. This work focuses on the transient response of such sensor and on the role of the carbon (C) content of the doped layers. A set of devices with different percentage of C incorporation in the doped layers is analyzed by measuring the scanner-induced photocurrent under different bias conditions, (ranging from -1.5V to 1V) in order to evaluate the response time.

This work presents preliminary results in the study of a novel structure for a laser scanned photodiode (LSP) type of image sensor. In order to increase the signal output, a stacked p-i-n-p-i-n structure with an intermediate light-blocking layer is used. The image and the scanning beam are incident through opposite sides of the sensor and their absorption is kept in separate junctions by an intermediate light-blocking layer. As in the usual LSP structure the scanning beam-induced photocurrent is dependent on the local illumination conditions of the image. The main difference between the two structures arises from the fact that in this new structure the image and the scanner have different optical paths leading to an increase in the photocurrent when the scanning beam is incident on a region illuminated on the image side of the sensor, while a decreasing in the photocurrent was observed in the single junction LSP. The results show that the structure can be successfully used as an image sensor even though some optimization is needed to enhance the performance of the device. © 2004 Elsevier B.V. All rights reserved.

Currently, microactuators are being developed using shape memory alloys (SMAs), which allow simple design geometries and provide large work outputs in restricted space. Several techniques have been used to produce NiTi shape memory alloy thin films, but from the practical point of view, only the sputter deposition method has succeeded so far. Vacuum evaporation of NiTi binary alloy entails the potential problem of the evaporation rates of each component not being the same due to differences in vapour pressure. Aiming to study the possible applications of SMAs to microfabrication, NiTi thin films were produced at CENIMAT by sputter and vacuum evaporation using raw materials from different sources. The films were analysed by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) at room temperature, as well as in situ high temperature, in order to characterise the temperature ranges at which the different structural transformations occur. © 2002 Elsevier Science B.V. All rights reserved.

The laser scanned photodiode (LSP) presents a new concept of image sensor with application in fields where low cost, large area and design simplicity are of major importance. Over the past few years this type of sensor has been under investigation and development, where several structures have been tested and characterized. In this work we present the physical explanation of device operating principle, with recourse to numerical simulation applied to structures with different compositions of the doped layers. An electrical model for this type of device is presented, enabling a fast evaluation of the device characteristics by means of an electrical simulation program. © 2006 Elsevier B.V. All rights reserved.

In recent works large area hydrogenated amorphous silicon p-i-n structures with low conductivity doped layers were proposed as single element image sensors. The working principle of this type of sensor is based on the modulation, by the local illumination conditions, of the photocurrent generated by a light beam scanning the active area of the device. In order to evaluate the sensor capabilities is necessary to perform a response time characterization. This work focuses on the transient response of such sensor and on the influence of the carbon contents of the doped layers. In order to evaluate the response time a set of devices with different percentage of carbon incorporation in the doped layers is analyzed by measuring the scanner-induced photocurrent under different bias conditions. © 2004 Elsevier B.V. All rights reserved.

The devices analyzed in this work present an S-shape J-V characteristic when illuminated. By changing the light flux a non linear dependence of the photocurrent with illumination is observed. Thus a low intensity light beam can be used to probe the local illumination conditions, since a relationship exists between the probe beam photocurrent and the steady state illumination. Numerical simulation studies showed that the origin of this S-shape lies in a reduced electric field across the intrinsic region, which causes an increase in the recombination losses. Based on this, we present a model for the device consisting of a modulated barrier recombination junction in addition to the p-i-n junction. The simulated results are in good agreement with the experimental data. Using the presented model a good estimative of the LSP signal under different illumination conditions can be obtained, thus simplifying the development of applications using the LSP as an image sensor, with advantages over the existing imaging systems in the large area sensor fields with the low cost associated to the amorphous silicon technology. © 2007 Materials Research Society.

Microcrystalline silicon is a two-phase material. Its composition can be interpreted as a series of grains of crystalline silicon imbedded in an amorphous silicon tissue, with a high concentration of dangling bonds in the transition regions. In this paper, results for the transport properties of a μc-Si:H p-i-n junction obtained by means of two-dimensional numerical simulation are reported. The role played by the boundary regions between the crystalline grains and the amorphous matrix is taken into account and these regions are treated similar to a heterojunction interface. The device is analyzed under AM1.5 illumination and the paper outlines the influence of the local electric field at the grain boundary transition regions on the internal electric configuration of the device and on the transport mechanism within the μc-Si:H intrinsic layer.

In this paper a set of one-dimensional simulations of a-Si:H p-i-n junctions under different illumination conditions and with different intrinsic layer are presented. The simulation program ASCA permits the analysis of the internal electrical behaviour of the cell allowing a comparison among the different internal configurations determined by a change in the input set. Results about the internal electric configuration will be presented and discussed outlining their influence on the current tension characteristic curve. Considerations about the drift-diffusion and the generation-recombination balance distributions, outlined by the simulation, can be used to explain the correlation between the basic device output, the i-layer characteristics (thickness and DOS), the incident radiation intensity and photon energy. © 2002 Elsevier Science B.V. All rights reserved.

Microcrystalline p-i-n silicon devices are a prospective contender for application in large-area optoelectronics. In this paper we analyse the behaviour of a μc-Si:H p-i-n photodevice under non-uniform illumination. The effect of a spatially non-uniform illumination is to create lateral electric fields and current flows inside the structure. We present in this paper a numerical application of a complete bidimensional model describing the transport properties within the structure. The continuity equations forholes and electrons together with Poisson's equation are solved simultaneously along the two directions parallel and perpendicular to the junction. The results of simulating p-i-n μc-Si:H junctions under non-uniform illumination show that the generated lateral effects depend not only in intensity but also in direction on the wavelength of the incident radiation. © 1997 Elsevier Science S.A.