Regina Monteiro

The densification during sintering of borosilicate glass matrix composites with 25 vol. % alumina (Al2O3) particles was investigated. The powder compacts, isostatically pressed at 200 MPa, were sintered at a temperature within the range 800-1000° C and maintained at this temperature during various times. The sintering behaviour of the composites was investigated by density measurement and by axial and radial shrinkage measurements. The crystalline phases present in the sintered composites were identified by XRD and the microstructure was analyzed by SEM. For temperatures up to 900°C, the relative density of the composites increased continuously with sintering temperature and sintering time, while for higher temperatures, the density increased rapidly and then slowed down to achieve a nearly constant value after sintering the composites for 30 minutes. The composites exhibited isotropic shrinkage behaviour when sintered at 800°C and 850°C, but at higher temperatures slightly higher axial shrinkage than radial shrinkage was observed. The shrinkage behaviour and microstructural characteristics of the composites indicate that densification during sintering can be attributed to the viscous flow of the borosilicate glass.

Cathode Ray Tube (CRT) waste glasses produced from dismantling TV sets were used to prepare glass foams by a simple and economic processing route, consisting of a direct sintering process of mixtures of CRT waste as glass powder with different foaming agents (coal fly ash and limestone quarrying residues). The influence of firing temperature, amount and type of foaming agent on the apparent density, pore size distribution and compressive strength have been studied. The aim of the work was to investigate the possibility to obtain glass foams using exclusively wastes as starting materials, and therefore replacing the conventional raw materials. © 2015 Taylor & Francis Group, London.

The thermoreactivity of a zinc acetate non-alkoxide solution used for the preparation of ZnO-based thin films was investigated in the temperature range 20-600°C by TG-DTA, XRD and SEM data. We found that the formation in air of ZnO crystallites from the sol-gel precursor occurs above 150°C simultaneously with the decomposition of an intermediary compound, most probably carbonate hydroxide (sciante and/or hydrozincite). At 200°C, the crystalline structure is well defined in terms of ZnO hexagonal lattice parameters, although residual organic compounds and water were not yet fully removed and an amorphous phase coexists. A kinetic investigation on the thermal decomposition of sol-gel precursor from DTA data using Kissinger differential equation is also presented. Apparent activation energy values of about. 100 kJ mol-1 corresponding to the non-isothermal decomposition of solid precursors in the temperature range 170-250°C have been found.

The thermal decomposition and crystallization behaviour of a sol-gel precursor used for the preparation of c-axis oriented Al-doped ZnO thin films were investigated in the temperature range 20-600°C by TG-DTA, IR spectroscopy and XRD analysis. At low temperature, the formation of ZnO crystallites from the sol precursor, prepared by dissolving Zn(CH 3COO)2·2H2O and AlCl 3·6H2O in 2-methoxyethanol and monoethanol amine, takes place via zinc carbonate hydroxide (sclarite/hydrozincite) and occurs simultaneously with the decomposition of this intermediary compound, which occurs above 150°C. At 200°C, the crystalline structure is well defined in terms of ZnO hexagonal lattice parameters, although an important amount of residual organic compounds and water was not yet removed. Increasing the treatment temperature up to 300, 400 and 600°C leads to a gradual removal of the residual organic compounds and therefore to a small change of the ZnO crystalline structure in terms of lattice parameters and grain size.

The surfaces of cordierite and glass particles were modified by coating them with an alumina precursor using a precipitation process in the presence of urea. Scanning electron microscopy (SEM), high-resolution transmission electron microscopy, X-ray diffraction, electrophoresis, and rheological measurements were used to characterize the coated powders. SEM and transmission electron microscopy morphologies of the coated powders revealed that amorphous and homogeneous coatings have been formed around the particles. The morphology of the coated powders showed a coiled wormlike surface. The coating Al2O3 layer dominated the surface properties of the coated glass and cordierite powders. The influence of the coating layer on the processing ability of cordierite-based glass-ceramics substrates by tape casting was studied in aqueous media. It could be concluded that the coating of the powders facilitates the processing and yields green and sintered tapes with denser, more homogeneous microstructures compared with the uncoated powders.

Hall effect measurements are one of the most powerful techniques for obtaining information about the conduction mechanism in polycrystalline semiconductor materials, which is the basis for understanding semiconductor gas sensors. In order to investigate the correlation between the microscopic characteristics and the macroscopic performances exhibited by undoped tin oxide gas sensors deposited by spray pyrolysis, Hall effect measurements were performed at different temperatures, from room temperature up to 500 K, and in the presence of two different atmospheres, air and methane. From these measurements, it was possible to infer the potential barrier and its dependence with the used atmosphere. The obtained results were analysed in terms of the oxygen mechanism at grain boundaries on the basis of the grain boundary-trapping model. In the presence of methane gas, the electrical resistivity decreases due to the lowering of the inter-grain boundary barrier height.

The crystallization of a commercial borosilicate glass powder has been studied in the temperature range 750-900°C. Crystal growth was investigated by high temperature XRD and cristobalite precipitation was identified. Glass devitrification exhibited a characteristic incubation period that decreased with increasing temperature: 25-30 min at 750°C, 9-12 min at 775°C, 5-10 min at 810°C, and 0-5 min at 840°C. Cristobalite is an unfavorable transformation product in terms of thermal expansion behavior. The precipitation of cristobalite in sintered glass compacts was confirmed by dilatometric analysis, where the increase in thermal expansion coefficient due to the presence of cristobalite and its transition from the tetragonal to the cubic phase were verified. Correlation between the XRD results and the dilatometric data from sintered glass compacts showed the partial dissolution of cristobalite when the glass was heated at the highest temperatures.

Cobalt oxide doped silica films were synthesized by a dip-coating technique. Initial compounds were cobalt acetate Co(CH3COO)2-4H 2O and tetraethoxysilane Si(OC2H5)4. The chemical composition was studied by X-ray diffraction and UV-Vis spectroscopy. The morphology analyses were carried out by means of atomic force microscopy. The average diameter of cobalt oxide dispersed particles increases with the molar ratio Co:Si and with the aging time of the initial colloidal solution. © 2009 American Institute of Physics.

Borosilicate glass-alumina composites with (1 - x) Glass + x Al 2O 3 (x = 0, 5, 10, 25 vol.%) were prepared and the effect of Al 2O 3 addition on the structural, electrical and thermal characteristics was investigated. XRD patterns revealed the presence of cristobalite (SiO 2) in sintered borosilicate glass and that the addition of Al 2O 3 hinders cristobalite formation. This behavior is due to the diffusion of some Al 3+ ions from alumina to glass, which leads to changes in glass structure and composition as identified by SEM/EDS. Cristobalite was undetected in composites containing 10% Al 2O 3 that attained the lowest thermal expansion coefficient value (∼4.6 × 10 -6 °C -1). Conductivity (dc and ac) increased with the amount of Al 3+ ions present in the glass structure as modifiers and formers. Dielectric constant values, in the range 5.0-7.2, increased with Al 2O 3 addition and the values of loss tan δ (1.5-2.1 × 10 -2) indicate that these materials are good insulators. © 2012 Elsevier B.V. All rights reserved.

This study deals with SiO2-P2O5 powders obtained by sol-gel process, starting from tetraethoxysilane (TEOS) as precursor for SiO2 and either triethylphosphate (TEP) or phosphoric acid (H3PO4) as precursors for P2O5. In the case of samples prepared with H3PO4, TG-DTA data showed an accentuated weight loss associated to an endothermic effect up to about 140 °C, specific for the evaporation of water and ethylic alcohol from structural pores, and also due to alkyl-amines evaporation. Sol-gel samples prepared with TEP exhibited different thermal effects, depending on the type of atmosphere used in the experiments, i.e. argon or air. XRD analysis revealed that annealed sol-gel samples prepared with H3PO4 showed specific peaks for silicophosphate compounds such as Si3(PO4)4, Si2P2O9, and SiP2O7. XRD results for annealed sol-gel samples prepared with TEP indicated mainly the presence of a vitreous (amorphous) phase, which could be correlated with SEM images. The presence of SiO2 in the sample might be expected. Thus, we have searched for any SiO2 polymorph possible to crystallize. Only potential peaks of cristobalite were identified but some of them are overlapping with peaks of other crystalline phosphates. SEM analysis indicated a decrease of the amount of crystalline phases with the increase in the annealing temperature. © 2009 Elsevier B.V. All rights reserved.

Various metal oxide-silica nanocomposite films have been recently proposed as gas-sensitive materials. This paper presents results on cobalt oxide-SiO2 mesoporous nanocomposite thin films templated by a cationic surfactant. The films were deposited on glass substrate by dip-coating process, using [Co(CH3COO)2]·4H2O and tetraethoxysilane (TEOS) as starting materials. The effect of withdrawal speed, number of layers and thermal treatment on the crystalline structure, morphology, Co-doping states, optical, electrical and gas sensing properties of the thin films has been investigated using X-ray diffraction, atomic force microscopy, X-ray photoelectron spectroscopy, optical transmittance and room temperature photoreduction-oxidation data. © 2007 Elsevier B.V. All rights reserved.

Barium zinc borosilicate glasses with a molar composition xBaO-(60-x)ZnO-30B 2O 3-10SiO 2, where x ranged from 0 to 60 mol%, were prepared using melt-quenching method. The effect of BaO substitution for ZnO on the sintering, crystallization, and dielectric characteristics has been investigated. The behavior of the studied barium zinc borosilicate glasses was mainly determined by the relative amount of the structural modifier oxides (BaO and ZnO) and the ionic size, and field strength of the modifying cations (Ba 2+, Zn 2+). Increased amounts of BaO decreased both glass transition temperature and crystallization temperature, while increasing the relative dielectric constant. Sintering occurred before crystallization for glasses where substitution of BaO for ZnO was up to 30 mol%, but for higher substitution levels, crystallization occurred during the sintering process hindering densification. © 2012 The American Ceramic Society.

The effect of rigid inclusions on the densification during isothermal sintering of glass matrix composites was investigated. Mixtures containing borosilicate glass powder and 0, 5, 10 and 25 vol. % alumina (Al 2O3) particles were prepared and powder compacts isostatically pressed at 200 MPa have been used. The sintering behaviour of the samples heated at 800°C during various times was investigated through density measurement, axial and radial shrinkage measurements. The microstructure was analysed by SEM and the crystalline phases present in the sintered composites were identified by XRD. The relative density of the isothermally treated borosilicate glass-Al2O3 composites decreased significantly with the increase in Al2O3 content because the presence of rigid inclusions retarded the densification of the compacts. The borosilicate glass exhibited anisotropic shrinkage behaviour, showing a radial shrinkage higher than the axial shrinkage and isotropic shrinkage was favoured by Al2O3 additions. Sintered glass showed a dense microstructure with some spherical closed pores. The microstructure of composites with 5 vol. % Al2O3 revealed that most of the pores were filled by capillary flow of the glass. The microstructure of composites with higher Al2O3 additions showed dense areas together with interconnected pores, which appeared at the sites of large glass particles in the green compacts.

Coal fly ashes produced by an extinguished power plant in the north of Portugal have been melted with addition of CaCO3 and Na2CO3 to obtain glasses. One of the formulated compositions was selected for further studies and it was possible to manufacture glass-ceramics by crystallizing the parent glass through adequate time-temperature schedules. The macroscopic appearance, microstructure, mechanical, thermal and chemical properties indicated that these materials are quite attractive for cladding applications, exhibiting in some cases better performances than the conventional ceramic tiles.

The present work investigates alumino-phosphate glasses from Li 2O-BaO-Al2O3-La2O3-P 2O5 system containing Sm3+ and Eu3+ ions, prepared by two different ways: a wet raw materials mixing route followed by evaporation and melt-quenching, and by remelting of shards. The linear thermal expansion coefficient measured by dilatometry is identical for both rare-earth-doped phosphate glasses. Comparatively to undoped phosphate glass the linear thermal expansion coefficient increases with 2 × 10-7 K-1 when dopants are added. The characteristic temperatures very slowly decrease but can be considered constant with atomic weight, atomic number and f electrons number of the doping ions in the case of Tg (vitreous transition temperature) and Tsr (high annealing temperature) but slowly increase in the case of Tir (low annealing temperature-strain point) and very slowly increase, being practically constant in the case of TD (dilatometric softening temperature). Comparatively to undoped phosphate glass the characteristic temperatures of Sm and Eu-doped glasses present lower values. The higher values of electrical conductance for both doped glasses, comparatively to usual soda-lime-silicate glass, indicate a slightly reduced stability against water. The viscosity measurements, showed a quasi-linear variation with temperature the mean square deviation (R 2) being ranged between 0.872% and 0.996%. The viscosity of doped glasses comparatively to the undoped one is lower at the same temperature. Thermogravimetric analysis did not show notable mass change for any of doped samples. DSC curves for both rare-earth-doped phosphate glasses, as bulk and powdered samples, showed Tg values in the range 435-450 C. Bulk samples exhibited a very weak exothermic peak at about 685 C, while powdered samples showed two weak exothermic peaks at about 555 C and 685 C due to devitrification of the glasses. Using designed melting and annealing programs, the doped glasses were improved regarding bubbles and cords content and strain elimination. © 2013 Elsevier B.V. All rights reserved.

The crystallization kinetics and phase transformation of a transparent Tb3+-doped lithium-aluminum phosphate glass, prepared by melt quenching, were investigated. The energy associated to the glass transition and the crystallization parameters (activation energy for crystallization and Avrami exponent) were evaluated by different methods using the experimental data obtained by differential thermal analysis performed at different heating rates. Using an isoconversional method to determine the change of the activation energy for crystallization with the fraction of crystallization, it was verified that with the increase in the fraction of crystallization from 0.1 to 0.9, the value of the activation energy decreased slightly from  370 to  310 kJ mol -1 and that the Avrami exponent varied from 0.8 to 1, suggesting a surface crystal growth mechanism. Observation of the microstructural evolution of heat-treated glass samples confirmed a surface crystallization process revealing spherulitic crystals constituted mainly by aluminum metaphosphate. © 2014 Springer Science+Business Media New York.

Cobalt oxide thin films were prepared by using the dipping sol-gel process. The films were deposited onto glass slides, starting from methanolic solution of cobalt acetate Co(CH3COO)2 · 4H2O. The effects of film thickness and sol concentration on structural and optical properties were studied. Structural analyses of Co3O4 films were performed by X-ray diffraction. The film thickness was varied by using different withdrawal speeds and the number of dipping-heating cycles. It was found that the grain size increases with the number of dipping N. The results point out to some compacting effect that increases with the number of dippings: the films exhibit direct and indirect optical transition, absorption coefficients are of the order of 104 cm-1, and upon annealing the absorption coefficient increases. © 2006 Elsevier B.V. All rights reserved.

The work deals with optical and structural properties of aluminophosphate glasses from Li2O-BaO-Al2O3-La 2O3-P2O5 system containing Sm 3 + and Eu3 + ions. X-ray fluorescence (XRF) has been used to establish the elemental composition of these materials. The influence of Sm3 + and Eu3 + ions on the optical properties of these glasses has been investigated in relation with their structural characteristics. The optical behavior of these materials has been studied by ultra-violet-visible (UV-Vis) spectroscopy, revealing absorption maxima specific to the doping ions. Structural information via vibration modes was provided by Fourier Transform Infrared (FTIR) absorption spectra evidenced as POP symmetrical and asymmetrical stretching vibration modes, POP bend, PO 2- symmetrical and asymmetrical stretching vibration modes, PO stretching vibration mode and POH water absorbance. Raman spectra acquired by 514.5 nm laser excitation disclosed peaks specific to metaphosphate network. Information about the elemental compositional homogeneity of Sm 3 + and Eu3 +-containing glasses as well as about the defects of the doped-glasses is revealed by scanning electron microscopy/energy dispersive spectrometry (SEM/EDS). Fluorescence spectroscopy measurements put in evidence important fluorescence peaks found at 596 nm and 643 nm for Sm 3 + ions in phosphate matrix and 611 nm and 700 nm in the case of Eu3 +-doped glass. © 2013 Elsevier B.V.

The isoconversional methods (Friedman (FR), Flynn-Wall-Ozawa (FWO) and Kissinger-Akahira-Sunose (KAS)) were applied for evaluating the dependencies of the activation energy (E) on the mass loss (Δm) corresponding to the non-isothermal decomposition of two Zn acetate-based gel precursors for ZnO thin films whose preparation differs by the drying temperature of the liquid sol-precursor (125°C for sample A, and 150°C for sample B). Although both investigated samples exhibit similar decomposition steps, strong differences between E vs. Δm curves as well as among the characteristic parameters of the decomposition steps, directly evaluated from TG, DTG and DTA curves, were put in evidence. © 2007 Springer Science+Business Media LLC.

The paper presents the properties of zinc oxide thin films deposited on glass substrate via dip-coating technique. Zinc acetate dehydrate, ethanol and monoethanol amine were used as starting materials and N2 gas was used as thermal annealing atmosphere for film crystallization. The effect of withdrawal speed on the crystalline structure, morphology, zinc and nitrogen chemical states, optical, electrical and gas-sensing properties of the thin films has been investigated using X-ray diffraction, atomic force microscopy, X-ray photoelectron spectroscopy, optical transmittance and photoreduction-ozone reoxidation data. © 2007 Elsevier B.V. All rights reserved.

A glass was made using bottom ash produced by a Portuguese municipal solid waste (MSW) incinerator. The bottom ash was the single batch material used in the formation of the glass, which was obtained through a conventional melt-quenching method. The glass was then converted to glass-ceramic for further recycling to construction materials. After submitting the glass samples to several heat treatments, between 820 and 1050°C and during different times, it was verified that the optimum heat treatment schedule for the ceramization of the glass was at 1000°C for 10h, as confirmed by microstructural observation and by X-ray diffraction. The major crystalline phases precipitated in the glass-ceramic were wollastonite (CaSiO3) and diopside (Ca(Mg,Al)(Si,Al)2O6). Microstructural analysis of the glass-ceramic revealed that the crystalline phases were present as dendrites and fiber-like structures that were homogeneously distributed in the material. The glassceramic showed good mechanical properties with a hardness of 5.6 MPa and a bending strength of 101 MPa. This material had a density of 2.8 gcm-3 and a thermal expansion coefficient of 9.10-6°C-1. The glass and the glass-ceramic showed an excellent chemical stability against leaching in acidic solution and in alkaline solution. In summary, both the glass and the glass-ceramic have good chemical and mechanical properties and can, therefore, be applied as construction materials.

In this work, the mechanical characterization of ceramic products processed from red clay with different amounts of added coal fly ash was investigated. Coal fly ash produced by power plants is a waste material that constitutes an alternative source of minerals for the production of traditional building ceramics, as it is a complex mixture of several oxides such as SiO2, Al2O3, CaO, Fe2O3, Na2O, TiO2, which are usually present in the composition of such ceramics. A powder technology and firing route was followed for the processing of the clay and coal fly ash based ceramics. Different proportions of waste (10, 25 and 50%, by weight) were added to red clay, and then the mixed powders were pressed to form compacts that were fired at a selected temperature in the range 850-1,150°C. The effects of waste content and of heating conditions on the microstructure and mechanical characteristics of the obtained materials were investigated. The density, porosity, water absorption, flexural strength, hardness and fracture toughness of the produced materials were evaluated. A comparison was made between the properties of the produced ceramics with those of traditional ceramic materials used in construction, e.g. floor or wall tiles, and it was observed that the clay based products with coal fly ash additions may be used in similar applications. © 2007 Springer Science+Business Media B.V.

This paper is mainly focused on the characterisation of a glass material (GM) obtained from the thermal treatment of a bottom ash (BA) produced at the Municipal Solid Waste (MSW) incineration plant of Valorsul. By melting the BA at 1400°C during 2 hours, and without using any chemical additives, a homogeneous black-coloured glass was obtained. The thermal and mechanical properties of this glass were characterised. The thermal expansion coefficient, measured by dilatometry, was 9-10 × 10-6 per °C and the modulus of rupture, determined by four-point bending test, was 75±6 MPa, which are similar values to those exhibited by commercial soda-lime-silica glasses used in structural applications. The chemical and the ecotoxicological leaching behaviour of the GM were also analysed. The GM was submitted to a leaching procedure composed of 15 sequential extraction cycles. A liquid/solid (L/S) ratio of 2 1/kg was applied in each cycle. The leachates were filtered through a membrane of PTFE (porosity: 0.45 μm). The filtered leachates were characterised for different chemical parameters and for an ecotoxicological indicator (bacterium Vibrio fischeri). The GM was also submitted to a microwave acidic digestion for the assessment of the total metal content. The crude BA was also submitted to the same experimental procedures. The GM showed levels of chemical emission and ecotoxicity for V. fischeri much lower than those determined for the crude BA. Similar characterisation studies will be pursued with the glass-ceramics produced by adequate thermal treatment of the glass, in order to investigate the effect of the crystallization on the final properties.

The kinetics of crystallization of transparent and conductive high preferential c-axis oriented Aldoped ZnO thin films on Corning 1737 glass substrate from amorphous sol-gel precursor prepared using zinc acetate and aluminum chloride as cations source, 2-methoxiethanol as solvent and monoethanolamine as sol stabilizer has been investigated. The effect of preheating temperature on the values of the kinetic parameters and crystallization mechanism is discussed. Some data concerning the microstructure, the electrical and optical properties of the thin films are presented.

{Aluminophosphate glasses belonging to the Li2O-BaO-Al 2O3- La2O3-P2O 5 system doped with Tb3+ were prepared and investigated. Methods as Induced Coupled Plasma-Mass Spectrometry (ICP-MS), Induced Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES) and X-ray diffraction (XRD) have been used to establish the elemental composition of these vitreous materials. The influence of the Tb3+ ions on the optical properties of the phosphate glasses has been investigated in relation with the structural characteristics of the vitreous matrix. The optical behavior has been studied by ultra-violet-visible (UV-Vis) spectroscopy, revealing electronic transitions specific for terbium ions. Fluorescence spectroscopy measurements have been performed by excitation in the UV and visible domains (377 nm and 488 nm) which resulted in the most significant fluorescence peaks in the Vis domain (540 and 547 nm). Structural information via vibration modes were provided by Fourier Transform Infrared (FTIR) absorption spectra in the 400-4000 cm-1 range. Absorption peaks specific for the vitreous phosphate matrix were put in evidence as P-O-P symmetrical and asymmetrical stretching vibration modes, P-O-P bend, PO2- symmetrical and asymmetrical stretching vibration modes