The two new pincer azomethine-thiophene ligands (N,NE',N,NE')-N,N'-(thiophene-2,5-diylbis(methan-1-yl-1-ylidene))bis(naphathalen-2-ylmethanamine) (L1) and (E)-(4,6-dihydropyren-1-yl)-N-((5-((E)-(pyren-1-ylmethylimino)ethyl)thiophen-2-yl)methylene)methanamine (L2), their absorption, fluorescence and MALDI-TOF-MS spectroscopic studies are described. The two systems synthesised combine the emissive probes pyrene and naphthyl with the good chelating properties of a tridentate SN2 donor-set from a thiophene Schiff-base ligand. Both ligands gave analytically pure solid complexes with Ni(II) and Pd(II) salts. The bichromophoric pyrene derivative L2 presents two emission bands in solution, one corresponding to the monomer species and a red-shifted band attributable to the intramolecular excimer. Ni(II) and Pd(II) complexation affects the conformation in solution, increasing the monomer emission at the expense of the excimer band; this effect could be explored in metal ion sensing. System L1 behaves as a non emissive probe. In situ complexation reactions followed by MALDI-TOF-MS spectrometry without matrix support have also been performed; these experiments show that L1 could be a potential chemosensor for Ni(II) and Pd(11). (c) 2007 Elsevier B.V. All rights reserved.

Reviews on software engineering literature have shown an insufficient experimental validation of claims, when compared to the standard practice in other well-established sciences. Poor validation of software engineering claims increases the risks of introducing changes in the software process of an organization, as the potential benefits assessment is based on hype, rather than on facts. The community lacks highly disseminated experimental best practices. We contribute with a model of the experimental software engineering process that is aligned with recent proposals for best practices in experimental data dissemination. The model can be used in the definition of software engineering experiments and in comparisons among experimental results.

n/a

n/a

In 1999, the DEECA/INETI and the UBiA/FCT/UNL started a researching project on the partition of heavy metals during the combustion of stabilised sewage sludge (Biogran®), in a fluidised-bed reactor, and on the quality of the bottom ashes and fly ashes produced. This project was entitled Bimetal and was funded by the Portuguese Foundation for Science and Technology. In this paper only the results on the combustion of Biogran® are reported. The combustion process was performed in two different trials, in which different amounts of sewage sludge and time of combustion were applied. Several ash samples were collected from the bed (bottom ashes) and from two cyclones (first cyclone and second cyclone ashes). Sewage sludge, bed material (sand) and ash samples were submitted to the leaching process defined in the European leaching standard EN 12457-2. The eluates were characterized for a set of inorganic chemical species. The ecotoxicological levels of the eluates were determined for two biological indicators (Vibrio fischeri and Daphnia magna). The results were compared with the limit values of the CEMWE French Regulation. The samples were also ranked according to an index based on the chemical characterization of the eluates. It was observed an increase of the concentration of metals along the combustion system. The ashes trapped in the second cyclone, for both combustion trials, showed the highest concentration of metals in the eluates. Chemically, the ashes of the second cyclone were the most different ones. In the ecotoxicological point of view, the ecotoxicity levels of the eluates of the ashes, for both combustion cycles, did not follow the same pattern as observed for the chemical characterization. The ashes of the first cyclone showed the highest ecotoxicity levels for V. fischeri and D. magna. This difference on chemical and ecotoxicological results proves the need for performing both chemical and ecotoxicological characterizations of the sub-products of such type of thermal processes.