Manuel J. Mendes Website

{\textless}p{\textgreater}Opto-electronics on/with paper is fostering a novel generation of flexible and recyclable devices for sunlight harvesting and intelligent optical sensing.{\textless}/p{\textgreater}

In this work, we highlight the influence of three different sol stabilizers, namely diethanolamine (DEA), Ammonium Hydroxide (NH4OH), and Nitric Acid (HNO3), on the optical and structural properties of spin-coated zinc oxide (ZnO) thin films. The XRD patterns related to all films exhibit a hexagonal crystal structure with a preferential orientation along the (0 0 2) direction. However an additional {\textless}100{\textgreater} peak arises when the films are prepared with DEA and NH4OH showing a better crystallinity than that displayed by HNO3-prepared films. The elaborated films show a high transparency reaching 80{%} for DEA-prepared films. The analysis of the transmittance and the reflectance measurements confirms a direct band-to-band transition. Depending on the sol stabilizer, the optical band gap energy is varying from 3.16 to 3.22 eV. The relatively wide band-gap of DEA-prepared ZnO films is correlated to their high crystallinity. Room temperature photoluminescence spectra indicate strong UV emission at around 377 nm originated from nearby band-edge transitions. Yet, the use of DEA as a stabilizer leads to a net intensity increase of the blue peak emission.

CO2 capture and utilization (CCU) technologies are being immensely researched as means to close the anthropogenic carbon cycle. One approach known as artificial photosynthesis uses solar energy from photovoltaics (PV), carbon dioxide and water to generate hydrocarbon fuels, being methane (CH4) a preferential target due to the already in place infrastructures for its storage, distribution and consumption. Here, a model is developed to simulate a direct (1-step) solar methane production approach, which is studied in two scenarios: first, we compare it against a more conventional 2-step methane production route, and second, we apply it to address the energetic needs of concept buildings with usual space and domestic hot water heating requirements. The analysed 2-step process consists in the PV-powered synthesis of an intermediate fuel – syngas – followed by its conversion to CH4 via a Fischer–Tropsch (methanation) process. It was found that the 1-step route could be adequate to a domestic, small scale use, potentially providing energy for a single-family house, whilst the 2-step can be used in both small and large scale applications, from domestic to industrial uses. In terms of overall solar-to-CH4 energy efficiency, the 2-step method reaches 13.26{%} against the 9.18{%} reached by the 1-step method. Next, the application of the direct solar methane technology is analysed for domestic buildings, in different European locations, equipped with a combination of solar thermal collectors (STCs) and PV panels, in which the heating needs that cannot be fulfilled by the STCs are satisfied by the combustion of methane synthesized by the PV-powered electrolyzers. Various combinations of situations for a whole year were studied and it was found that this auxiliary system can produce, per m2 of PV area, in the worst case scenario 23.6 g/day (0.328 kWh/day) of methane in Stockholm, and in the best case scenario 47.4 g/day (0.658 kWh/day) in Lisbon.

© 2017 The growing interest in exploring thin film technologies to produce low cost devices such as n-i-p silicon solar cells, with outstanding performances and capability to address the highly relevant energy market, turns the optimization of their fabrication process a key area of development. The usual one-dimensional analysis of the involved parameters makes it difficult and time consuming to find the optimal set of conditions. To overcome these difficulties, the combination of experimental design and statistical analysis provides the tools to explore in a multidimensional fashion the interactions between fabrication parameters and expected experimental outputs. Design of Experiment and Multivariate Analysis are demonstrated here for the optimization of: (1) the low temperature deposition (150 °C) of high quality intrinsic amorphous silicon (i-a-Si:H); and (2) the matching of the n-, i-, and p-silicon layers thickness to maximize the efficiency of thin film solar cells. The multiple regression method applied, validated through analysis of variance and evaluated against exact numerical simulations, is shown to predict the overall intrinsic layer properties and the devices performance. The results confirm that experimental design and statistical data analysis are effective approaches to improve, within a minimum time frame and high certainty, the properties of silicon thin films, and subsequently the layer structure of solar cells.

Nowadays there is a strong demand for intelligent packaging to provide comfort, welfare and security to owners, vendors and consumers by allowing them to know the contents and interact with the goods. This is of particular relevance for low cost, fully disposable and recyclable products, such as identification tags and medical diagnostic tests, and devices for analysis and/or quality control in food and pharmaceutical industries. However, the increase of complexity and processing capacity requires continuous power and can be addressed by the combined use of a small disposable battery, charged by a disposable solar cell, which is able to work under indoor lighting. Herein, we show a proof-of-concept of the pioneering production of thin-film amorphous silicon (a-Si:H) solar cells with an efficiency of 4{%} by plasma enhanced chemical vapour deposition (PECVD) on liquid packaging cardboard (LPC), which is commonly used in the food and beverage industries. Such accomplishment put us one step closer to this revolution by providing a flexible, renewable and extremely cheap autonomous energy packaging system. Moreover, such Si thin films take advantage of their good performance at low-light levels, which also makes them highly desirable for cheap mobile indoor applications.

The employment of printing techniques as cost-effective methods to fabricate low cost, flexible, disposable and sustainable solar cells is intimately dependent on the substrate properties and the adequate electronic devices to be powered by them. Among such devices, there is currently a growing interest in the development of user-oriented and multipurpose systems for intelligent packaging or on-site medical diagnostics, which would greatly benefit from printable solar cells as their energy source for autonomous operation. This chapter first describes and analyzes different types of cellulose-based substrates for flexible and cost effective optoelectronic and bio devices to be powered by printed solar cells. Cellulose is one of the most promising platforms for green recyclable electronics and it is fully compatible with large-scale printing techniques, although some critical requirements must be addressed. Paper substrates exist in many forms. From common office paper, to packaging cardboard used in the food industry, or nanoscale engineered cellulose (e.g. bacterial cellulose). However, it is the structure and content of paper that determines its end use. Secondly, proof-of-concept of optoelectronic and bio devices pro-duced by inkjet printing are described and show the usefulness of solar cells as a power source or as a chemical reaction initiator for sensors.

One of the most promising approaches to produce industrial-compatible Transparent Conducting Materials (TCMs) with excellent characteristics is the fabrication of TCO/metal/TCO multilayers. In this article, we report on the electro-optical properties of a novel high-performing TCO/metal/TCO structure in which the intra-layer is a micro-structured metallic grid instead of a continuous thin film. The grid is obtained by evaporation of Ag through a mask of polystyrene colloidal micro-spheres deposited by the Langmuir-Blodgett method and partially dry-etched in plasma. IZO/Ag grid/IZO structures with different thicknesses and mesh dimensions have been fabricated, exhibiting excellent electrical characteristics (sheet resistance below 10 $Ømega$/□) and particularly high optical transmittance in the near-infrared spectral region as compared to planar (unstructured) TCM multilayers. Numerical simulations were also used to highlight the role of the Ag mesh parameters on the electrical properties.

Metal nanoparticles and diffractive nanostructures are widely studied for enhancing light trapping efficiency in thin-film solar cells. Both have achieved high performance enhancements, but there are very few direct comparisons between the two. Also, it is difficult to accurately determine the parasitic absorption of metal nanoparticles. Here, we assess the light trapping efficiencies of both approaches in an identical absorber configuration. We use a 240 nm thick amorphous silicon slab as the absorber layer and either a quasi-random supercell diffractive nanostructure or a layer of self-assembled metal nanoparticles for light trapping. Both the plasmonic and diffractive structures strongly enhance the absorption in the red/near-infrared regime. At longer wavelengths, however, parasitic absorption becomes evident in the metal nanoparticles, which reduces the overall performance of the plasmonic approach. We have formulated a simple analytical model to assess the parasitic absorption and effective reflectivity of a plasmonic reflector and to demonstrate good agreement with the experimental data.

© 2017 by the authors. In the present study, zinc oxide (ZnO) nanorods (NRs) with a hexagonal structure have been synthesized via a hydrothermal method assisted by microwave radiation, using specialized cardboard materials as substrates. Cardboard-type substrates are cost-efficient and robust paper-based platforms that can be integrated into several opto-electronic applications for medical diagnostics, analysis and/or quality control devices. This class of substrates also enables highly-sensitive Raman molecular detection, amiable to several different operational environments and target surfaces. The structural characterization of the ZnO NR arrays has been carried out by X-ray diffraction (XRD), scanning electron microscopy (SEM) and optical measurements. The effects of the synthesis time (5-30 min) and temperature (70-130 °C) of the ZnO NR arrays decorated with silver nanoparticles (AgNPs) have been investigated in view of their application for surface-enhanced Raman scattering (SERS) molecular detection. The size and density of the ZnO NRs, as well as those of the AgNPs, are shown to play a central role in the final SERS response. A Raman enhancement factor of 7 × 105was obtained using rhodamine 6 G (RG6) as the test analyte; a ZnO NR array was produced for only 5 min at 70 °C. This condition presents higher ZnO NR and AgNP densities, thereby increasing the total number of plasmonic "hot-spots", their volume coverage and the number of analyte molecules that are subject to enhanced sensing.

The copper zinc tin sulfide (CZTS) compound is a promising candidate as an alternative absorber material for thin-film solar cells. In this study, we investigate the direct formation of Cu1.92ZnSnx(Sb1-x)S4 compounds [CZT(A)S], with x=1, 0.85, 0.70, and 0.50, via a mechanochemical synthesis (MCS) approach, starting from powders of the corresponding metals, zinc sulfide, and sulfur. The thermal stability of the CZT(A)S compounds was evaluated in detail by in situ synchrotron high-energy x-ray diffraction measurements up to 700 °C. The CZT(A)S compounds prepared via MCS revealed a sphalerite-type crystal structure with strong structural stability over the studied temperature range. The contribution of the MCS to the formation of such a structure at room temperature is analyzed in detail. Additionally, this study provides insights into the MCS of CZTS-based compounds: the possibility of a large-scale substitution of Sn by Sb and the production of single phase CZT(A)S with a Cu-poor/Zn-poor composition. A slight increase in the band gap from 1.45 to 1.49-1.51 eV was observed with the incorporation of Sb, indicating that these novel compounds can be further explored for thin-film solar cells.

The optical properties of localized surface plasmon resonances (LSPR) sustained by self-assembled silver nanoparticles are of great interest for enhancing light trapping in thin film photovoltaics. First, we report on a systematic investigation of the structural and the optical properties of silver nanostructures fabricated by a solid-state dewetting process on various substrates. Our study allows to identify fabrication conditions in which circular, uniformly spaced nanoparticles are obtainable. The optimized NPs are then integrated into plasmonic back reflector (PBR) structures. Second, we demonstrate a novel procedure, involving a combination of opto-electronic spectroscopic techniques, allowing for the quantification of useful and parasitic absorption in thin photovoltaic absorber deposited on top of the PBR. We achieve a significant broadband useful absorption enhancement of 90{%} for 0.9 µm thick $μ$c-Si:H film and demonstrate that optical losses due to plasmonic scattering are insignificant below 730 nm. Finally, we present a successful implementation of a plasmonic light trapping scheme in a thin film a-Si:H solar cell. The quantum efficiency spectra of the devices show a pronounced broadband enhancement resulting in remarkably high short circuit current densities (Jsc).

Plasmonic light trapping in thin film silicon solar cells is a promising route to achieve high efficiency with reduced volumes of semiconductor material. In this paper, we study the enhancement in the opto-electronic performance of thin a-Si:H solar cells due to the light scattering effects of plasmonic back reflectors (PBRs), composed of self-assembled silver nanoparticles (NPs), incorporated on the cells{&}{\#}x2019; rear contact. The optical properties of the PBRs are investigated according to the morphology of the NPs, which can be tuned by the fabrication parameters. By analyzing sets of solar cells built on distinct PBRs we show that the photocurrent enhancement achieved in the a-Si:H light trapping window (600 {&}{\#}x2013; 800 nm) stays in linear relation with the PBRs diffuse reflection. The best-performing PBRs allow a pronounced broadband photocurrent enhancement in the cells which is attributed not only to the plasmon-assisted light scattering from the NPs but also to the front surface texture originated from the conformal growth of the cell material over the particles. As a result, remarkably high values of Jsc and Voc are achieved in comparison to those previously reported in the literature for the same type of devices.

The spectra of localized surface plasmon resonances (LSPRs) in self-assembled silver nanoparticles (NPs), prepared by solid-state dewetting of thin films, are discussed in terms of their structural properties. We summarize the dependences of size and shape of NPs on the fabrication conditions with a proposed structural-phase diagram. It was found that the surface coverage distribution and the mean surface coverage (SC) size were the most appropriate statistical parameters to describe the correlation between the morphology and the optical properties of the nanostructures. The results are interpreted with theoretical predictions based on Mie theory. The broadband scattering efficiency of LSPRs in the nanostructures is discussed towards application as plasmon-enhanced back reflectors in thin-film solar cells.

{\textless}h2{\textgreater}Summary{\textless}/h2{\textgreater}{\textless}p{\textgreater}Recent trends in photovoltaics demand ever-thin solar cells to allow deployment in consumer-oriented products requiring low-cost and mechanically flexible devices. For this, nanophotonic elements in the wave-optics regime are highly promising, as they capture and trap light in the cells' absorber, enabling its thickness reduction while improving its efficiency. Here, novel wavelength-sized photonic structures were computationally optimized toward maximum broadband light absorption. Thin-film silicon cells were the test bed to determine the best performing parameters and study their optical effects. Pronounced photocurrent enhancements, up to 37{%}, 27{%}, and 48{%}, respectively, in ultra-thin (100- and 300-nm-thick) amorphous, and thin (1.5-$μ$m) crystalline silicon cells are demonstrated with honeycomb arrays of semi-spheroidal dome or void-like elements patterned on the cells' front. Also importantly, key advantages in the electrical performance are anticipated, since the photonic nano/micro-nanostructures do not increase the cell roughness, therefore not contributing to recombination, which is a crucial drawback in state-of-the-art light-trapping approaches.{\textless}/p{\textgreater}