Hugo C. Biscaia

Externally bonded fiber-reinforced polymer (FRP) composites have been widely used for the strengthening and repairing of reinforced concrete (RC) beams. Existing studies have denstrated that the full-range behavior and the associated debonding mechanism of the FRP-to-concrete interface between two adjacent cracks in the FRP-plated RC beam are different from those of the pull-off bonded joint. Moreover, the bond behavior between the FRP and the concrete may be affected by interfacial thermal stresses induced by the service temperature variations (i.e., the thermal loadings). Based on a fully reversible bilinear bond-slip model, this paper presents an analytical study to investigate the full-range deformation behavior of the FRP-to-concrete interface between two adjacent cracks under combined mechanical and thermal loadings. The analytical results have indicated that the thermal loadings may significantly influence the full-range deformation behavior and the axial stress distribution of the FRP plate, although the material properties of concrete, adhesive, and FRP are assumed to be not affected by the service temperature variations. A temperature increase leads to an increase in the ultimate load of the bond interface and vice versa. A finite element (FE) model with different considerations of the bondline damage is developed to verify the proposed analytical solution. The reliability of the proposed analytical solution is then validated by the comparisons between the analytical results and the corresponding predictions provided by the FE model. © 2022 Elsevier Ltd

Debonding failures of FRP have been frequently observed in laboratory tests of reinforced concrete (RC) beams flexurally-strengthened with near-surface mounted (NSM) fibre-reinforced polymer (FRP). A number of numerical and theoretical studies have been carried out to predict debonding failures in NSM FRP-strengthened beams, and several strength models have also been proposed. The existing studies, however, were all based on the scenario of a simply supported beam tested under one or two-point loading, while the influence of load distribution has not yet been investigated. This paper presents the first ever study into the effect of load distribution on the behaviour of NSM FRP-strengthened RC beams. A series of large-scale RC beams flexurally-strengthened with NSM FRP strips were first tested under different load uniformities; then a finite element (FE) model, which can give close predictions to the behaviour of such strengthened beams, was developed; finally, the proposed FE model was utilized to investigate the influence of bond length of NSM FRP on the load uniformity effect. It was found that the load uniformity has a significant effect on the beam behaviour, and the degree of this effect varies with the bond length of NSM FRP. © 2021 Elsevier Ltd

Mechanical anchorage devices have the potential to efficiently improve the bond behavior of Carbon Fiber-Reinforced Polymers (CFRP) Externally Bonded (EB) onto steel with an adhesive. Existing relevant studies, however, have been very limited. Against this background, experimental and numerical studies on the double overlapped CFRP-to-steel bonded joints with an end mechanical anchorage were carried out in the present study. Two types of CFRP laminates (i.e., SIKA CFRP and the other type made in Harbin Institute of Technology – HIT) were used in the bond tests, with or without end mechanical anchorage devices. The test results showed that the end mechanical anchorage had marginal effect on the bond-slip relationship between EB CFRP and steel as well as debonding load, but could increase the ultimate load. It was also found that CFRP laminate from HIT had a better bond performance than that from SIKA, in terms of both debonding load and ultimate load. Using ABAQUS, Finite Element (FE) model was established on such bonded joints and the accuracy was verified with test results. The verified FE model was adopted in a parametric study to further clarify the effect of key parameters on the bond behavior of such bonded joints. © 2021 Elsevier Ltd

Nowadays, the use of the Digital Image Correlation (DIC) technique has spread and it is being used in several engineering areas to measure displacements. The available data obtained from the DIC measurement to evaluate the bond performance between a Carbon fibre Reinforced Polymer (CFRP) externally bonded to a timber substrate is scarce. From the existing data obtained with other materials, this contactless technique revealed to be quite useful but its accuracy with other well-established techniques, such as the use of electric strain gauges is not well understood yet. Therefore, the current work aims to study the accuracy of 2D DIC measurements with the measurements obtained from the use of strain gauges within a low-cost perspective. To that end, several CFRP-to-timber bonded joints were tested under the single-lap shear test and different bonding techniques were considered as well. Some flaws intrinsically derived from the DIC measurements that complicate the bond assessment, such as the fluctuations in the generated displacements field, are identified, and to bypass this problem a new methodology is proposed. This new methodology is based on two different closed-form solutions that, after defining the local and global bond behaviours of different CFRP-to-timber bonded joints, allowed to eliminate the fluctuations found from the DIC measurements, facilitating the estimation and the comprehension of the full debonding process of the CFRP-to-timber joints, which was achieved with a good proximity to the homologous debonding process derived from the strain gauge measurements. © 2020

In this paper, the influence of salt fog and ambient condition exposure on CFRP-to-steel bonded joints (CSJs) with a near end mechanical anchorage was studied. The tests of the CSJs were carried out with a monotonic loading history respectively with and without a near end mechanical anchorage both unaged and after being exposed to the ageing conditions. The results revealed failures in the adhesive for some CSJs with a near end mechanical anchorage, among which also exhibited the best bond performance both in aged and unaged specimens. Due to the high state of degradation after ageing exposure, local damage of the CFRP located at the gap position of the CSJs was induced by a torsion action during the fixation of the specimen in the tensile machine even prior to the testing, which caused, although locally, severe delamination of the CFRP of the aged CSJs. From the torsion test results, a decrease in the torsional capacity of the CFRP after aging revealed the degradation of the carbon fiber-to-matrix interface. Additional results reflected that a drop in the initial stiffness of the load vs. slip relationship can be observed, caused by a pre-crack with a length of 30 mm in the CSJs. © 2021 Elsevier Ltd

The use of optic measurements such as digital image correlation to take strain measurements of fibre-reinforced polymers bonded to a substrate has been on the increase recently. This technique has proven to be useful to fully characterize the bond behaviour between two materials. Although modern digital cameras can take high-definition photos, this task is far from simple due to the tiny displacements that need to be measured. Consequently, digital image correlation measurements lead to relative errors that, at an initial stage of the debonding process, are higher than those calculated close to the debonding of the fibre-reinforced polymer from the substrate. This study aims to evaluate and analyse the use of the digital image correlation technique on the bond between carbon fibre-reinforced polymer laminates and timber when subjected to a pull-out load consistent with fracture Mode II. To allow the quantification of the relative errors obtained from the digital image correlation measurements during the full debonding process, several strain gauges were used to measure the strains in the carbon fibre-reinforced polymer composite. The accuracy of the digital image correlation measurements is analysed by comparing it with those obtained from the strain gauges, which is a very well-established measuring technique. Another contribution of this study is to check the versatility of the digital image correlation measurements on a broader range of situations. To that end, several timber prisms were bonded with seven different bonding techniques with and without the installation of a mechanical anchorage at the carbon fibre-reinforced polymer unpulled end. The results showed that the digital image correlation technique was able to track the slips calculated from the strain gauge measurements until the debonding load, but after that, some difficulties to measure the displacements of the anchored carbon fibre-reinforced polymer-to-timber joints were detected. The digital image correlation technique also over predicted bond stresses when compared with those taken from the strain gauges, which led to bond–slip relationships with higher bond stresses. © The Author(s) 2021.