Carlos Chastre

An analysis on the effect of the incorporation of coarse recycled concrete aggregates on the bond strength between concrete and embedded steel reinforcement is presented. The model’s uncertainty of the Level I provision of the anchorage length of fib Bulletin 72 on ribbed steel/recycled aggregate concrete bond is quantified. Afterwards, reliability analyses on the bond strength are made and a partial safety factor for the anchorage length of recycled concrete elements is proposed. The model’s uncertainty is evaluated through data from pullout tests, the only type of bond test that has been so far performed extensively on recycled aggregate concrete specimens. The limitations of this test in reproducing the bond of actual structural elements is discussed, and the model’s uncertainty is converted to that of lap splice tests. The bond strength of recycled aggregate concrete design was found to be less reliable than that of natural aggregate concrete, especially in the absence of confining reinforcement. For concrete with full recycled aggregate incorporation, a 25% increase in the anchorage length is proposed. Additional testing on the bond strength of lapped splices or beam-end specimens is recommended.

This paper analyses the studies made so far on the variability and reliability of recycled aggregate concrete. Since recycled aggregate concrete is seen by different agents of the construction industry as a variable material and no structural code has specifically been calibrated to its use, its role as a structural material is limited. Such calibration is hindered since specific research on the statistical and probabilistic data of recycled aggregate concrete properties is lacking.Investigations on the probabilistic knowledge of recycled aggregates and recycled aggregate concrete properties are discussed, and the studies made so far on the reliability of recycled aggregate concrete elements are summarised. Final remarks regarding the future prospects towards the consensual acceptance of recycled aggregate concrete structures are provided.

An investigation on the scatter of code-type constitutive models that relate compressive strength (fc) with tensile strength (fct) and Young’s modulus (Ec) of standard concrete specimens is presented. The influence of the mix design on the accuracy of the fc vs. fct and fc vs. Ecrelationships is discussed, with emphasis on the lithological type and morphology of the coarse aggregates. The uncertainty of the constitutive models is analysed in probabilistic terms and random variables that model the uncertainty of the fc vs. fct and fc vs. Ec relationships are proposed for reliability analyses of serviceability limit states. The suitability of the models proposed is assessed through preliminary conservative estimates of their design values.

This paper evaluates and compares the statistics of compressive strength data from three Portuguese ready-mixed concrete plants. A hierarchical model showed that different groups of concrete strength records are not statistically equivalent, even if they were produced in the same plant and using the same concrete composition. This finding is related to autocorrelation. For the same specified strength class, compositions produced less often result in higher average compressive strength and variability. The statistics of one of the plants were quite different from those of the others, even though the concrete of this plant also complied with the specifications. It was found that the average compressive strength of a mix may be quite dependent on the plant that produced it, even if the compressive strength complies with quality control specifications. Conformity with the target slump and strength class was checked following the conformity criteria of EN 206-1 for continuous production. Nonconformity with slump is more frequent than failure to comply with the strength class. A bias factor for reliability analyses was proposed.

The bias factor of the Eurocode 2 [CEN (European Committee for Standardization) (2008). Eurocode 2: Design of ConcreteStructures–Part 1-1: General Rules and Rules for Buildings] and ACI 318 [ACI (American Concrete Institute) (2014). Building CodeRequirements for Structural Concrete and Commentary] flexural resistance models of reinforced concrete beams are compared withemphasis on the effect of the incorporation of coarse recycled aggregates sourced from concrete waste. The bias factor of the yielding momentcalculations according to both codes is also investigated, and the bias in the cracking moment when Eurocode 2 material clauses are used. Thedatabase was composed of 174 beams, and the criteria that led to its development are discussed. The effect of recycled aggregate incorporationon the statistical descriptors of the bias factor is evaluated and probabilistic modeling using lognormal distributions is argued for. Preliminarypartial safety factors for the bias factor of recycled aggregate concrete beams are proposed. No significant differences in the bias of theultimate moment were found between the two comparison vectors: Eurocode 2 versus ACI 318 specifications and recycled versus naturalcoarse aggregate. The bias of the cracking moment increased when coarse recycled aggregates were incorporated, most probably due to thehigher heterogeneity of recycled aggregates.

Research on the variability of the properties of recycled aggregate concrete is lacking and is necessary for the development of reliability analyses and code calibration procedures. This paper presents an experimental programme on the within-batch variability of the compressive strength, Young’s modulus, and splitting tensile strength of several recycled and natural aggregate concrete mixes. The influence of the recycled concrete aggregates on the mechanical properties and variability of concrete is analysed and discussed and benchmarks with standard predictions for the variability of natural aggregate concrete are made. It was found that full recycled aggregate concrete incorporation did not increase the variability of any of the properties tested, but intermediate ratios of recycled aggregate incorporation did. The properties of high-strength concrete mixes were more variable than that of all other mixes, irrespective of recycled aggregate incorporation. All properties of all compositions were suitably modelled by normal distributions. The coarse recycled aggregates were sourced from concrete waste.

This paper investigates the effect of recycled coarse aggregate incorporation on the relationship between 150 mm cubic and Փ 150 mm cylindrical compressive strength (the reference strength of standards) by comparing data from recycled and natural aggregate concrete compositions in which both cubes and cylinders were tested. A conversion factor from cubic to cylindrical strength is proposed in two versions: A deterministic and a probabilistic one. Such factor has not been studied before and researchers have been converting cubic data as if natural aggregate concrete were tested. The probabilistic factor is intended for reliability analyses on the structural behaviour of recycled aggregate concrete using data from laboratory cube tests. It was found that the incorporation of recycled coarse aggregates sourced from concrete waste significantly decreases the expected value of the factor but the factor’s scatter is relatively unaffected.

Este artigo avalia se, para especificações de betão correntes, a resistência à compressão de betão pronto é significativamente dependente da central que o produziu, bem como se a variabilidade entre amassaduras de uma determinada composição é dependente da classe de resistência especificada. É apresentado um parâmetro probabilístico que converte a resistência à compressão característica especificada para a resistência à compressão expectável em provetes de betão cúbicos em condições padronizadas.É feita uma análise estatística e probabilística dos resultados de ensaios de resistência à compressão aos 28 dias de betão pronto produzido em três centrais de betão portuguesas durante o ano de 2017. Após a avaliação da representatividade da base de dados analisada, é feito um estudo comparativo dos parâmetros estatísticos dos dados de produção das diferentes centrais e é avaliada a influência da classe de resistência à compressão do betão nestes parâmetros. Define-se e analisa-se um parâmetro probabilístico que converte a resistência à compressão especificada para a resistência potencial de betão, para cubos de 150 mm. Este parâmetro contribui para uma futura proposta de um modelo probabilístico, a ser utilizado em análises de fiabilidade, que converte a resistência à compressão especificada para a resistência à compressão de elementos de betão em obra.Quer a análise estatística dos ensaios de resistência à compressão, quer o parâmetro de conversão são comparados com os resultados de investigações internacionais na área, aferindo-se se a qualidade da produção de betão pronto nacional é semelhante à de outras regiões.

A produção de betão com substituição de agregados naturais por agregados reciclados minimiza os impactes da indústria da construção. Contudo, o recurso a este tipo de agregado é limitado devido a dúvidas dos diferentes agentes da indústria da construção e à ausência de regulamentação específica para o projecto de betão com agregados reciclados. A percepção de betões com agregados reciclados como um material heterogéneo com comportamento imprevisível é o principal entrave, quer para a aceitação da indústria, quer para o desenvolvimento de regulamentação. Diferentes aspectos relacionados com o efeitos da variabilidade das propriedades de betão com agregados reciclados na regulamentação de estruturas são abordados conceptualmente: a heterogeneidade dos agregados reciclados, o efeito desta heterogeneidade nas propriedades mecânicas de betão e os efeitos da variabilidade das propriedades de betão na sua fiabilidade estrutural. Os primeiros resultados de uma campanha experimental desenvolvida especificamente para abordar o efeito de agregados grossos reciclados na fiabilidade são apresentados e as suas implicações no projecto de estruturas discutidas. São apresentadas sugestões de desenvolvimentos futuros que visam a calibração de coeficientes parciais de segurança que possibilitem o projecto de estruturas de betão armado dimensionadas segundo o formato do Eurocódigo 2 e mantendo os mesmos níveis de segurança de betão convencional.

This paper investigates whether the model uncertainty of reinforced recycled aggregate concrete (RAC) beams subjected to bending differs from that of reinforced natural aggregate concrete (NAC) beams. An introductory remark concerning the importance of the codification of RAC structural design is made and notions concerning model uncertainties and their role on structural codification are given. Afterwards, the criteria used in the construction of a database of RAC and NAC beams are referred before presenting the key findings of an analysis on the model uncertainty of the cracking, yielding and ultimate moments of beams subjected to four-point bending tests. The analytical moments were calculated following Eurocode 2 provisions. Probabilistic models for model uncertainties are proposed. Negligible differences in the model uncertainty of NAC and RAC beams are reported.

TThis chapter concerns the need to evaluate the reliability of structural elements produced with recycled aggregates concrete (RAC) in order to address some designers’ scepticism towards the use of this eco-friendly material. The current knowledge on RAC’s behaviour demonstrates its viability for structural purposes. However, of the investigations performed so far very few are related to a fundamental aspect towards RAC world-wide application as a structural material: structural codes have a probabilistic basis.After briefly presenting the state-of-the-art knowledge on the material properties and structural behaviour of RAC, the limitations of the current knowledge are debated. Afterwards, an introduction to structural codification is presented, as well as the fundamentals of reliability analysis. Examples of code verifications are contextualized with their underlying assumptions and the information necessary for code calibration is discussed. The role of reliability in the calibration of structural codes is shown, common techniques for reliability calculations are briefly explained, and relevant references in the area are cited for the readers’ perusal.Having established how structural codes are calibrated, the state-of-the-art on the probabilistic and statistical knowledge of RAC properties is reviewed. The implications of the very reduced number of studies on this area are discussed and the need to conduct further studies is emphasized.Afterwards, investigations that used reliability analysis to calibrate partial safety factors applicable to RAC are reviewed. The methodology of each investigation is presented, the experimental tests that led to the definition of the probabilistic information of the RAC’s parameters are described and the need to have a wide range of data coming from different RAC compositions and aggregate sources is debated.This chapter finishes by contextualizing the current knowledge on RAC properties with the necessary information for code calibration procedures. The relevance of a code proposal towards RAC affirmation as a structural material is highlighted, as well as the requirements of such code. Suggestions for future studies are made.

This document has a broad scope and is not focussed on design issues. Precast construction under seismic conditions is treated as a whole. The main principles of seismic design of different structural systems, their behavior and their construction techniques are presented through rules, construction steps and sequences, procedures, and details that should lead to precast structures built in seismic areas complying with the fundamental performance requirements of collapse prevention and life safety in major earthquakes and limited damage in more frequent earthquakes.The content of this document is largely limited to conventional precast construction and, although some information is provided on the well-known “PRESSS technology” (jointed ductile dry connections), this latter solution is not treated in detail in this document.The general overview, contained in this document, of alternative structural systems and connection solutions available to achieve desired performance levels, intends to provide engineers, architects, clients, and end-users (in general) with a better appreciation of the wide range of applications that modern precast concrete technology can have in various types of construction from industrial to commercial as well as residential. Lastly, the emphasis on practical aspects, from conceptual design to connection detailing, aims to help engineers to move away from the habit of blindly following prescriptive codes in their design, but instead go back to basic principles, in order to achieve a more robust understanding, and thus control, of the seismic behaviour of the structural system as a whole, as well as of its components and individual connections.

A reabilitação de um edifício tem muitas vezes de ser analisada e efetuada tendo em conta os edifícios vizinhos e a envolvente. No caso particular da reabilitação de um edifício, à partida devem considerar-se, de forma integrada, todos os requisitos que não são cumpridos face aos padrões atuais. Com base nessa análise, e tendo em conta muitas vezes condicionantes vários, que vão desde estéticos, técnicos, culturais a económicos, e que dependem em larga medida das tipologias construtivas, a intervenção tem de ser cuidadosamente concebida, preparada e executada. Apresentam-se sinteticamente as tipologias construtivas mais correntes, o contexto legislativo português da construção e específico da reabilitação. Efetua-se uma análise à legislação vigente, detalhando com maior detalhe o Regime Especial da Reabilitação Urbana, que possibilita dispensas de cumprimentos regulamentares mas apenas relativos a aspetos construtivos. Por esse motivo apresenta-se também uma síntese de aspetos relativos à segurança estrutural na reabilitação de edifícios com tipologias correntes. Pretende-se, através desta síntese, contribuir para uma visão mais integrada da reabilitação.

The enhancement of the mechanical behaviour of reinforced concrete (RC) columns with regard to axial compression is an up-to-date concern, namely if the strengthening of existing structures is to be considered. In view of this, external confinement with FRP systems has been tested in order to become a feasible technique, since it seems to have important advantages over other systems such as its high strength and stiffness in relation to weight and its improvement of strength and ductility while confining RC columns. Square columns confined with FRP show a more complex interpretation of their behaviour, when compared to circular columns. Accordingly, the present work includes the analysis of two experimental programs regarding axial compression on CFRP confined RC columns: one on circular and square specimens with different corner radii; the other on square specimens with side lengths ranging from medium to large. Based on this, modelling equations are proposed to predict maximum axial load, axial strain and lateral strain, as well as the entire behaviour until failure with curves of axial load-axial strain and axial load-lateral strain. The modelling results show that the analytical curves are in general agreement with the presented experimental curves for a wide range of dimensions.

A indústria do betão pré fabricado é, por tradição, inovadora, precursora de novas tecnologias e de novos materiais.O processo produtivo de estruturas com elementos pré-fabricados difere significativamente do das estruturas betonadas em obra pelo facto de uma parte, ou a totalidade, dos elementos da estrutura serem produzidos em fábrica, em condições de produção melhoradas em relação às condições da obra, e serem posteriormente transportados para a obra, onde são, finalmente ligados entre si. A produção em fábrica é efectuada em ambiente protegido do Sol e da chuva, com operários fixos e com formação profissional para desenvolverem tarefas com procedimentos normalizados. Consequentemente, os elementos executados em fábrica possuem melhor qualidade, sob vários aspectos, do que as estruturas executadas em obra.Este livro divide-se em duas grandes áreas, numa primeira abordam-se algumas aplicações de estruturas pré-moldadas no mundo e numa segunda parte descreve-se o seu comportamento estrutural face a diferentes acções. Nos primeiros capítulos relata-se a experiência da pré-fabricação em três países de diferentes continentes: o Brasil, Portugal e a Austrália e revelam-se novas oportunidades que poderão surgir para a indústria da pré-fabricação. Nos capítulos seguintes dá-se um especial enfoque à investigação do comportamento das ligações (rígidas e semi-rígidas). Aborda-se o projecto de estruturas de betão pré-fabricado às acções acidentais. E por fim, dedicam-se os últimos capítulos ao comportamento das estruturas pré-fabricadas face às acções sísmicas. Nesta área, o bom desempenho das estruturas e grande parte do conhecimento e da tecnologia actual advém da resposta dada pelos engenheiros, investigadores e construtores aos fenómenos naturais que afectam as nossas construções, como comprova o desempenho das ligações dúcteis resistentes a momentos em edifícios pré fabricados de betão no verdadeiro teste sísmico que foram os sismos de Christchurch de 2010 e 2011.

The strengthening of reinforced concrete structures with FRP materials has received a
considerable increment in recent years due to the high strength-weight and stiffness-weight
ratios of FRP compared to other materials.
An experimental programme was conducted in order to analyse the behaviour of different
structural solutions to strengthen reinforced concrete beams with FRP composites (EBR
GFRP, EBR CFRP, NSRM-CFRP) and is described. The RC T beams had a 3m span by 0.3m
height and were tested until rupture in a 4-point bending test system.
The NSMR technique has proved to be the most effective of the three alternatives tested, as it
obtained high strength, combined with high ductility. Nevertheless, all the systems show
great strength increment in relation to the non retrofitted T-beams, proving to be effective
approaches to the flexural strengthening of RC beams.

The aim of the present communication is to present an analysis of the gravity load influence on the hysteretic behaviour of a beam-column connection. For this purpose, in the experimental campaign a new procedure for RC cyclic tests is presented in order to reproduce closer demands on the beam critical zone than the traditional procedures. The Experimental campaign included cyclic tests of the specimens according with the ECCS recommendation and an innovate procedure. The test results are presented, compared and analysed. A numerical simulation of the tests is presented where the model for the hysteretic response of the beam was calibrated with the experimental results. Finally, the behaviour of a portal frame system under cyclic displacements up to a drift of 3.5% was analysed, assuming that the non-linearity is concentrated on the plastic hinges, considering different levels of gravity load. Thus it is intended to assess the influence of the gravity load on the behaviour of a structure subjected to cyclic loads.

n/a