António Manuel Pinho Ramos

This work presents an experimental study concerning the post-punching behaviour of flat slabs strengthened with a new technique based on post-tensioning with anchorages by bonding using an epoxy adhesive. This strengthening technique proved efficient with respect to ultimate and serviceability states. Five slab specimens were tested in the post-punching range and it was found that the post-punching resistance was on average 78{%} of the punching resistance. This paper reports the development of strand forces and slab displacements from the beginning of the tests, including the bond stresses developed at several stages of the loading process. It was observed that top reinforcement bars were capable of transmitting post-punching loads to the prestressing strands. Taking this into account and based on the load bath envisaged from the column to the slab, expressions for the vertical load capacities corresponding to the parts of the load path are presented and compared with the experimental results, showing their ability to predict both ultimate loads and modes of failure. Compared with other strengthening techniques, the one proposed here not only upgrades ultimate and serviceability behaviour but also adds post-punching resistance, which is a great advantage in the event of progressive collapse, since it may avoid the collapse of an entire structure, thus reducing the risk of material and human losses.

The progressive collapse of structures generally results in the loss of human lives. Experience shows that flat slab structures are very sensitive to progressive collapse, which may cause serious accidents if special detailing is not provided. The post-punching behaviour of a column-supported slab is decisive in the progressive collapse development. This work presents the experimental research carried out to study the post-punching behaviour of prestressed concrete flat slabs. Six reduced-scale prestressed concrete flat slab models were tested. The tests were carried out in two different phases. In the first phase the models were loaded up to failure by punching. Afterwards, the models were loaded again to study the post-punching behaviour changes caused by the presence of unbonded, prestressed tendons and the influences of their distance to the column.

The objective of this study was to analyse the behaviour of prestress strand anchorages by bonding with an epoxy adhesive for structural strengthening use. Pull-out and push-in tests were carried out on 15·2 mm diameter prestress steel strands sealed in 18 mm diameter holes with several embedment lengths, complemented by long-term tests. Experimental results are presented and compared with theoretical results regarding maximum pull-out and transmittable loads and also draw-in results. Theoretical results are obtained by solving the governing equation of the bond phenomenon adopting a non-linear local bond/slip law derived from pull-out tests with short embedment length. The study shows that it is reasonable to assume an average constant bond stress for anchorage design with the studied epoxy adhesive in the range of the studied values of anchor embedment length and diameter. The average values for bond stress to be used for determining the maximum pull-out and transmittable loads were found to be 12·0 and 5·2 MPa, respectively. Experimental draw-in values show a great variability, and so determining transmission length based on draw-in values may lead to a false perception that the transmission length is very variable.

The aim of this work is to study the behaviour of reinforced concrete flat slab structures under combined vertical and horizontal cyclic loading. A total of five specimens were cast and tested: a control specimen was punched without eccentricity, one specimen was tested under constant vertical loading and monotonically increased eccentricity until failure and the remaining three were tested under constant vertical load, at different shear ratios, and cyclic horizontal loading with increasing horizontal drift ratios. All slabs were similar, measuring 4.25×1.85×0.15m3. The reinforced concrete slab specimens were connected to two steel half columns by 0.25×0.25m2 rigid steel plates, prestressed against the slab using steel bolts, to ensure monolithic behaviour. The cyclic tests were performed using an innovative test setup that allows bending moment redistribution, line of inflection mobility, assures equal vertical displacements at the North-South borders and symmetrical shear forces. Results show that cyclic horizontal actions are very harmful to the slab–column connection, resulting in low horizontal drifts and energy dissipation.

n/a

The experimental research carried out to study the punching behavior of high strength concrete (HSC) flat slabs is reported in the present work. Three flat slab specimens were cast using HSC and another one with normal strength concrete (NSC), to be used as a reference slab. The HSC mix presented a compressive strength of about 130MPa, with a basalt coarse aggregate. The tested specimens were square with 1650mm side and 125mm thickness. The longitudinal reinforcement ratio varied between 0.94{%} and 1.48{%}. The experimental results show that the use of HSC led to a significant load capacity increase when compared with the reference model made with NSC. Furthermore, the experimental results also indicated that as the longitudinal reinforcement ratio increased, the punching capacity also increased. The results obtained in this set of experimental tests and others collected from the literature were compared with the code provisions by EC2, MC2010 and ACI 318-11.

This paper deals with punching of reinforced high strength concrete (HSC) flat slabs. Despite the use of HSC increased significantly in the last years, the experimental research on punching behavior of HSC slabs is still limited. Furthermore, most of this past research adopted concrete compressive strength lower than 90 MPa. In a previous work by this research group three specimens with concrete compressive strength around 120 MPa and one with normal strength concrete (NSC) were tested. The present work represents the continuation of the previous activity and it is focused on the rational use of HSC. Four specimens with HSC and one of NSC were tested under monotonic vertical loading. The HSC was placed only in the slab-column connection region and it was limited to a thin layer in the compressive zone, in order to have a more economical and sustainable solution. This rational use of the HSC showed excellent results in terms of punching strength. Limiting the HSC to a thin layer in the compressive zone resulted in an almost equal punching strength to that obtained with the slab entirely casted in HSC.

n/a

n/a

n/a

n/a

High-strength concrete (HSC) slab-column connections with relatively low concrete strengths compared to today’s capabilities have been tested under seismic-type loading in the past. Herein, the hybrid use of HSC with compressive strength approximately 120 MPa and normal-strength concrete (NSC) is investigated through three reversed horizontal cyclic-loading tests with different geometries of the HSC region and a reference NSC specimen. The results show that HSC applied in the vicinity of the column can significantly enhance the seismic performance of slab-column connections. The best result in terms of drift capacity and economic use of HSC was achieved in the case of full-depth HSC extended from the column’s face up to 2.5 times the effective depth. Drift ratios up to 3.0% were achieved. A comparison with previous tests showed that the hybrid use of HSC and NSC can achieve similar results to the provision of punching shear reinforcement.

n/a

n/a

The results of a series of experiments on four reinforced concrete flat slab specimens with shear studs and a control specimen without any shear reinforcement are presented. The specimens were tested under constant gravity loads and reversed horizontal cyclic displacements. The main test variables were the applied gravity load and the number of perimeters of studs. One of the specimens was tested in two phases to study the postearthquake behavior. Results showed a considerable improvement of the deformation capacity of specimens with studs compared to the reference specimen. In agreement with previous research, increasing the applied gravity shear ratio resulted in a lower experimental drift capacity. It is shown that a better explanation of the observed ultimate drifts can be made by considering also the flexural capacity and the extent of shear reinforcement. The specimen tested in two phases exhibited considerable residual capacity, even after severe horizontal loading.

The results of a series of experiments on four reinforced concrete flat slab specimens with shear studs and a control specimen without any shear reinforcement are presented. The specimens were tested under constant gravity loads and reversed horizontal cyclic displacements. The main test variables were the applied gravity load and the number of perimeters of studs. One of the specimens was tested in two phases to study the postearthquake behavior. Results showed a considerable improvement of the deformation capacity of specimens with studs compared to the reference specimen. In agreement with previous research, increasing the applied gravity shear ratio resulted in a lower experimental drift capacity. It is shown that a better explanation of the observed ultimate drifts can be made by considering also the flexural capacity and the extent of shear reinforcement. The specimen tested in two phases exhibited considerable residual capacity, even after severe horizontal loading.

Advances in concrete technology during the last decades have resulted in the development of materials with enhanced mechanical properties, such as High Strength Concrete (HSC), Fibre Reinforced Concrete (FRC) and Ultra-High Performance Fibre Reinforced Concrete (UHPFRC). The application of these materials in flat slabs, which are a popular structural solution in Reinforced Concrete (RC) buildings worldwide, has the potential of significantly reducing raw material consumption by enabling the design of slenderer and therefore lighter structures. However, flat slabs are susceptible to punching shear failure, which is a complex phenomenon that remains challenging, even though significant efforts have been made to experimentally study it. For advanced concrete materials (HSC, FRC and UHPFRC), the challenge is further accentuated by the continuous and rapid development of these materials. With the purpose of identifying and highlighting gaps in the published literature, a review of tests with HSC, FRC and UHPFRC slab-column connections in non-seismic and seismic loading applications is presented in this paper. It is shown that future research directions in this field include, among others, testing thicker slabs, HSC slabs with higher concrete compressive strength, HSC combined with FRC and several more cases related to seismic loading conditions.

The use of randomly distributed steel fibres in the concrete mix improves its mechanical properties. In the particular case of a flat slab-column connection, this solution can provide slabs with an increased load capacity and deformation capacity, allowing a potential reduction of reinforcement. This work presents the experimental study of the behaviour of SFRC flat slabs up to failure under a concentrated loading, accompanied by the study of the mechanical properties of the SFRC, which consisted in three-point loading notched beams, compression and splitting tests. In this study, the hooked end steel fibre dosages varied between 0{%} and 1.25{%} by volume. Test results showed that the inclusion of steel fibres influences both slab stiffness and its load capacity. Increments of load capacity up to 64{%} were obtained in slabs with SFRC compared with the reference slab without fibres. The experimental results were compared with the predictions provided by several existing models. © 2014 Elsevier Ltd. All rights reserved.